Metra HDCC-01 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra HDCC-01 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
HDCC-01
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 7/6/18 INSTHDCC-01
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Small flat-blade
screwdriver • Tape • Wire cutter • Zip ties
TABLE OF CONTENTS
Connections to be made .......................................2
Installing the HDCC-01............................................3
Programming the HDCC-01 ....................................3
Setting the factory clock .......................................3
Troubleshooting .....................................................3
Honda Clock Retention 2012-2014
APPLICATIONS
Provides accessory power (12-volt 10-amp)
Can be used in non-amplified, or amplified models
Provides NAV outputs (parking brake, reverse, speed sense)
ASWC-1 harness included (ASWC-1 sold separately)
Retains balance and fade
Retains the ability to set the factory clock
Retains the factory AUX-IN jack
Micro “B” USB updatable
• HDCC-01 interface • HDCC-01 harness
• 8-pin subwoofer harness
• 16-pin harness with stripped leads
HONDA
Civic * (without NAV) 2013 CR-V (without NAV) 2012-2014
* All trims except LX
2
CONNECTIONS TO BE MADE
From the 16-pin harness with stripped leads to the aftermarket radio:
Connect the Red wire to the accessory wire.
Connect the Orange/White wire to the illumination wire. If the aftermarket radio does not
have an illumination wire, tape it off and disregard it.
Tape off and disregard the Gray Gray/Black White White/Black Brown, , , , and wires, they
will not be used in this application.
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the Light Green wire to the parking brake wire (if applicable).
Connect the Blue/Pink wire to the VSS or speed sense wire (if applicable).
Connect the Green/Purple wire to the reverse wire (if applicable).
From the HDCC-01 harness to the aftermarket radio:
Connect the Black wire to the ground wire.
Connect the Yellow wire to the battery wire.
If the vehicle is equipped with a factory amplifier, connect the Blue/White wire to amp
turn-on wire.
If the vehicle is equipped with a factory AUX-IN jack and desired to be retained, connect the
Red & RCA jacks to the AUX-IN jack.White
For the following (8) wires, if the vehicle does not have a factory amplifier, cut off the RCA jacks
to expose the speaker wires.
Connect the White wire to the left front positive speaker output.
Connect the White/Black wire to the left front negative speaker output.
Connect the Gray wire to the right front positive speaker output.
Connect the Gray/Black wire to the right front negative speaker output.
Connect the Green wire to the left rear positive speaker output.
Connect the Green/Black wire to the left rear negative speaker output.
Connect the Purple wire to the right rear positive speaker output.
Connect the Purple/Black wire to the right rear negative speaker output.
From the 8-pin subwoofer harness to the aftermarket radio (amplified models only):
Connect the White RCA to the subwoofer output.
12-pin pre-wired ASWC-1 harness:
This harness is to be used along with the optional ASWC-1 (not included) to retain steering
wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If it will be
used, please refer to the ASWC-1 instructions for radio connections and programming.
Disregard the harness that comes with the ASWC-1.
For the CR-V 2014: If the vehicle is equipped with Bluetooth controls, and desired to be
retained, connect the Gray/Blue wire to the Yellow wire (pin-15) in the 32-pin harness at the
factory Bluetooth module located in the center of the dash, below the radio.
3
REV. 7/6/2018 INSTHDCC-01
With the key in the off position:
Connect the 16-pin harness with stripped leads, and the HDCC-01 harness, into the interface.
If an ASWC-1 (sold separately) will be used, do not connect it until the HDCC-01 is
programmed and fully functional.
Attention! Do not connect the HDCC-01 harness to the wiring harness in the vehicle just yet.
For the steps below, the L.E.D. located inside the interface can only be seen while active. The
interface does not need to be opened to see the L.E.D.
1. Start the vehicle.
2. Connect the HDCC-01 harness to the wiring harness in the vehicle. The L.E.D. will initially be
Green to indicate the interface is powered.
3. After a few seconds the L.E.D. will turn on solid Red while the interface automatically
programs to the vehicle. The radio will shut off at this point. This process should take 5 to 30
seconds.
4. After the interface is programmed, the L.E.D. will turn on solid Green, and the radio will
come back on, indicating programming was successful.
5. Test all functions of the installation for proper operation, before reassembling the dash.
6. If the interface fails to function, refer to “Troubleshooting”.
Resetting the Axxess interface
1. The Blue reset button is located inside the Axxess interface, between the two connectors.
The button is accessible outside the Axxess interface, no need to open the Axxess interface.
2. Press and hold the reset button for two seconds, then let go to reset the Axxess interface.
3. Refer to “Programming the Axxess Interface” from this point.
The buttons on the steering wheel will be used to set the factory clock.
Press and hold the SOURCE button on the steering wheel for 15 seconds to access the clock
setting mode.
Press SEEK-UP or SEEK-DOWN to select hours, minutes, etc. Press VOLUME-UP or
VOLUME-DOWN to set the values.
Either press SOURCE again, or wait 5 seconds with no activity to exit the clock setting mode
.
INSTALLING THE HDCC-01
PROGRAMMING THE HDCC-01 TROUBLESHOOTING
SETTING THE FACTORY CLOCK


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: HDCC-01

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra HDCC-01 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-