Metra GMOS-MOST-01 Bedienungsanleitung

Metra Nicht kategorisiert GMOS-MOST-01

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra GMOS-MOST-01 (16 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/16
GMOS-MOST-01
I N S TA L L AT I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 10/7/19 INSTGMOS-MOST-01
Product Info
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink
• Small flat blade screwdriver • Tape
• Wire cutter • Zip ties • T-15 Torx screwdriver
TABLE OF CONTENTS
Connections ........................................................ 2-4
Installation .............................................................5
Programming ..................................................... 5-6
Audio level adjustment ........................................7
GM MOST® Amplifier Interface 2014-Up
APPLICATIONS
Provides accessory power
(12-volt 10-amp)
Maintains the retained
accessory power (R.A.P.) feature
Retains OnStar / OE Bluetooth
Retains warning chimes
Provides NAV outputs (parking
brake, reverse, speed sense)
Requires ASWC-1 (sold separately)
if steering wheel audio controls
are desired to be retained
Retains the factory AUX-IN jack
Retains the factory backup
camera
Used in MOST® amplified
applications
Retains balance
Micro-B USB updatable
CHEVROLET
Colorado 2015-2018
Silverado 1500 2014-2018
Silverado 2500/3500 2015-2018
Suburban 2015-Up
Tahoe 2015-Up
GMC
Canyon 2015-2018
Sierra 1500 2014-2018
Sierra 2500/3500 2015-2018
Yukon / Yukon XL 2015-Up
• GMOS-MOST-01 interface
• GMOS-MOST-01 harness
• 16-pin harness with stripped leads
• Backup camera harness
• 10-pin jumper harness
• 12-pin jumper harness
2
CONNECTIONS
From the 16-pin harness with stripped leads to the aftermarket radio:
Connect the wire to the accessory wire.Red
Connect the Orange/White wire to the illumination wire. If the aftermarket radio does not
have an illumination wire, tape off the Orange/White wire.
Connect the wire to the amp turn on wire. This wire must be connected to hear Blue/White
sound from the factory amplifier.
Connect the wire to the right front positive speaker output.Gray
Connect the Gray/Black wire to the right front negative speaker output.
Connect the wire to the left front positive speaker output.White
Connect the wire to the left front negative speaker output.White/Black
Connect the wire to the left rear positive speaker output.Green
Connect the wire to the left rear negative speaker output.Green/Black
Connect the wire to the right rear positive speaker output.Purple
Connect the wire to the right rear negative speaker output.Purple/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the wire to the parking brake wire.Light Green
Connect the wire to the speed sense wire.Blue/Pink
Connect the wire to the reverse wire.Green/Purple
Tape off and disregard the Brown wire, it will not be used in this application.
From the GMOS-MOST-01 harness to the aftermarket radio:
Connect the wire to the ground wire.Black
Connect the Yellow wire to the battery wire.
If retaining the factory AUX-IN jack is desired, connect the and RCA jacks to the Red White
audio AUX-IN jacks from the aftermarket radio.
Note: a) The jack can only be used if it is a single jack.
b) If the jack has a USB port as well, neither can be retained.
Disregard the wire, it will not be used in this application.Red
Tape off and disregard the 3.5mm jack, it will not be used in this application.
DIN jack:
Disregard the DIN jack, it will not be used in this application.
Note: The relay attached to the GMOS-MOST-01 harness is only for audible turn signal
clicks. No extra steps are required to retain this feature, so leave the relay as-is.
Continued on the next page
3
REV. 10/7/2019 INSTGMOS-MOST-01
CONNECTIONS (CONT )
Continued on the next page
From the 10-pin or 12-pin jumper harness to the vehicle:
If the vehicle
does not
have a CD or DVD-Drive, disregard these steps.
For models
without
rear seat entertainment:
Connect the
female
10-pin jumper harness, to the Black
male
10-pin harness Black
removed from the CD-Drive.
For models
with
rear seat entertainment:
Connect the
female
12-pin jumper harness, to the Black
male
12-pin harness Black
removed from the DVD-Drive.
Note: Even though this step must be done for models with rear seat entertainment,
the rear seat entertainment system will not be retained by this interface.
(Figure A)
Human Machine Interface module
(Arrow points to the location)
(Figure B)
From the backup camera harness:
To the aftermarket radio:
Connect the Yellow RCA jack to the backup camera input.
To the vehicle:
Connect the backup camera harness, to the male Gray connector removed from the
Human Machine Interface module (HMI). (Figure A)
For the Chevy Colorado and GMC Canyon:
The HMI module is located in the radio cavity, down low.
For all other models:
The HMI module is located behind the glove box. There are (2) modules behind the glove
box. The HMI module is behind the metal dashboard support. (Figure B)
Drop the glove box down by first removing the retaining cable on the right side. Then
squeeze the glove box sides and gently pull down.
Remove (6) T-15 Torx screws securing the plastic panel now exposed.


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: GMOS-MOST-01

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra GMOS-MOST-01 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-