Metra GMOS-06 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra GMOS-06 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 54 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Installation instructions for part GMOS-06
REV. 10/5/2015 INSTGMOS-06
axxessinterfaces.com • metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Axxess Integrate
CAUTION!
Metra recommends disconnecting the negative bat
-
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and speed sense)
• Retains chimes
• Retains OnStar / OE Bluetooth
• Adjustable volume for chimes and OnStar
• Prewired ASWC-1 harness included (ASWC-1 sold separately)
• High level speaker input
• For use in amplified systems
• Retains balance and fade
• Micro B USB updatable
20;-,(;<9,:
• Cutting tool • Crimping tool • Tape • Connectors
(example: butt-connectors, bell caps, etc.)
;663:9,8<09,+
Cadillac Bose Interface
1997-2005
GMOS-06
• GMOS-06 interface • GMOS-06 harness
• 16-pin harness with stripped leads
05;,9-(*,*64765,5;:
(7730*(;065:
CADILLAC
Deville 1998-2005
Eldorado 1998-2002
Seville 1998-2004
Catera 1997-2001
GMOS-06
2
From the 16-pin harness with stripped leads to the aftermarket radio:
• Connect the (2) wires to the accessory wire.Red
Note: If installing the ASWC-1, there will be an accessory wire in the
12-pin harness to connect as well.
•
Cap off and disregard the wire, it will not be used in this applicationOrange/White
.
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the Green wire to the left rear positive speaker output.
• Connect the Green/Black wire to the left rear negative speaker output.
• Connect the Purple wire to the right rear positive speaker output.
• Connect the Purple/Black wire to the right rear negative speaker output.
• Connect the Blue/White wire to the amp turn-on wire.
This wire must be connected to turn the interface on.Note:
• Connect the Brown wire to the mute wire. If the aftermarket radio does not
have a Mute wire, tape up the wire. If the wire is not connected, Brown Brown
the radio will turn off when OnStar is activated.
Connections to be made
The following wires are for the aftermarket radios that have navigation built in:
• Connect the Light Green wire to the parking brake wire (if applicable).
• Connect the Blue/Pink wire to the speed sense wire (if applicable).
• Connect the Green/Purple wire to the reverse wire (if applicable).
From the GMOS-06 harness to the aftermarket radio:
• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the 12-volt battery wire.
• Connect the Blue wire to the power antenna wire.
• Connect the Orange/White wire to the illumination wire. If the aftermarket
radio has no illumination wire, tape off the wire. Orange/White
• The (3) Black/White wires are to be grounded only if engine noise is present.
• The Black/Yellow wire is for the OnStar volume adjustment. This will be
discussed in the OnStar Level Adjustment section.
12-pin pre-wired ASWC-1 harness:
This harness is to be used along with the optional ASWC-1 (not included) to
retain steering wheel audio controls. If the ASWC-1 is not being used, disregard
this harness. If it will be used, please refer to the ASWC-1 instructions for radio
connections and programming.
Note: Disregard the harness that comes with the ASWC-1.
To the aftermarket radio:
• Connect the Red wire to the accessory wire
GMOS-06
3
• Connect the 16-pin harness with stripped leads into the interface.
• Connect the GMOS-06 harness into the interface, and then into the vehicle.
• With all connections completed, reconnect the negative battery terminal.
• Initialize the interface by turning the ignition on for 30 seconds, then turn the
ignition back off, then back on again.
Note: If using the ASWC-1, connect it after you initialize the GMOS-06, with the
key in the off position.
Installing the GMOS-06 Adjusting the GMOS-06
Testing the GMOS-06
Audio Level Adjustment:
• With the vehicle and radio turned on, turn the volume up 3/4 of the way.
• Locate the end of the GMOS-06 with the 16-pin harness with stripped leads.
• With a small screwdriver, adjust the potentiometer clockwise to raise the audio
level; counterclockwise to lower the audio level.
• Once at a desired level, the audio level adjustment is complete.
Chime Volume Adjustment:
• With the vehicle on, turn it off and leave the key in the ignition. Open the driver’s
door; chimes will be heard.
• Wait 10 seconds, and then with a small screwdriver, turn the potentiometer
clockwise to raise the chime level; counterclockwise to lower the chime level.
Note: The potentiometer is located on the side of the interface where the
16-pin harness with stripped leads is connected to.
• When the chime level is at a desired level, remove the key from the ignition.
This will lock the chime volume at its current level.
OnStar Level Adjustment:
• Press the OnStar button to activate it.
• While OnStar is speaking, press the VOLUME UP or VOLUME DOWN buttons on
the steering wheel to raise or lower the OnStar level.
• If the vehicle does not come equipped with steering wheel controls, find the
Black/Yellow wire on the GMOS-06 harness.
•
While OnStar is speaking, tap the Black/Yellow wire to ground. Once the OnStar level
is set, it will stay at that level until the Black/Yellow wire is tapped to ground again.
• Push the OnStar button; the radio should mute, and you should hear the OnStar
voice. Push the OnStar cancel button; the radio should un-mute and play again.
Note: The radio will turn off instead if the mute wire is not connected.


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: GMOS-06

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra GMOS-06 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-