Metra Axxess XSVI-1731-NAV Bedienungsanleitung

Metra Nicht kategorisiert Axxess XSVI-1731-NAV

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Metra Axxess XSVI-1731-NAV (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Installation instructions for part XSVI-1731-NAV
REV. 9/29/2016 INSTXSVI-1731-NAV
®
axxessinterfaces.com • metraonline.com © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
Axxess Integrate
®
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
• Provides NAV outputs (parking brake, reverse, and speed sense)
• Pre-wired ASWC-1 harness included (ASWC-1 sold separately)
• Retains the factory backup camera
• Retains balance and fade
• Includes the AX-CAM6V 12-volt to 6-volt converter
• Micro “B” USB updatable
FEATURES
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
TOOLS REQUIRED
XSVI-1731-NAV
Honda Data Interface 2016-up
APPLICATIONS
• XSVI-1731-NAV interface • XSVI-1731-NAV harness • AX-CAM6V 12-volt to 6-volt converter
INTERFACE COMPONENTS
HONDA
Civic LX 2016-up
Connections to be made ................................................... 2
Installing the XSVI-1731-NAV .......................................... 3
Initializing the XSVI-1731-NAV ........................................ 3
TABLE OF CONTENTS
XSVI-1731-NAV
®
2
Connections to be made
From the XSVI-1731-NAV harness to the aftermarket radio:
•
Connect the wire to chassis ground, and also to the Black wire of the AX-CAM6V.Black
• Connect the Yellow wire to the battery wire.
• Connect the Red wire to the accessory wire.
• If the vehicle is equipped with a factory backup camera:
• Connect the Red wire labeled “6-volt camera” to the AX-CAM6V (sold separately).
• Connect the Yellow RCA jack to the backup camera input.
• If the aftermarket radio has an illumination wire, connect the wire to it.Orange
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Green wire to the left rear positive speaker output.
• Connect the Green/Black wire to the left rear negative speaker output.
• Connect the Purple wire to the right rear positive speaker output.
• Connect the Purple/Black wire to the right rear negative speaker output.
The following (3) wires are only for multimedia/navigation radios that require
these wires.
• Connect the Blue/Pink wire to the VSS/speed sense wire.
• Connect the Green/Purple wire to the reverse wire.
Note: Before connecting this wire, also refer to the “AX-CAM6V 12-volt to 6-volt”
converter section.
• Connect the Light Green wire to the parking brake wire.
AX-CAM6V 12-volt to 6-volt converter:
• Connect the Blue/Red Red wire to the wire labeled “Camera Power 6V”.
• Connect the Blue/White Green/Purple wire to the wire.
Note: The wire will connect to both the AX-CAM6V, Green/Purple
and the aftermarket radio.
12-pin pre-wired ASWC-1 harness:
• This harness is to be used along with the optional ASWC-1 (not included) to
retain steering wheel audio controls. If the ASWC-1 is not being used, disregard
this harness. If it will be used, please refer to the ASWC-1 instructions for radio
connections and programming.
Note: Disregard the harness that comes with the ASWC-1.
• Connect the Red wire to the accessory wire.
XSVI-1731-NAV
®
3
Installing the XSVI-1731-NAV
With the key in the off position:
• Connect the XSVI-1731-NAV harness into the interface, and then to the harness in
the vehicle.
Attention! If the interface loses power for any reason, the following steps will need to be
performed again. Also, if installing an ASWC-1 connect it after you initialize and test the
interface/radio, with the key in the off position.
• Turn the key (or push-to-start button) to the ignition position and wait until the radio
comes on.
Note: If the radio does not come on within 60 seconds, turn the key to the off
position, disconnect the interface, check all connections, reconnect the interface,
and then try again.
• Turn the key to the off position, and then to the accessory position. Test all functions
of the installation for proper operation, before reassembling the dash.
Initializing the XSVI-1731-NAV


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: Axxess XSVI-1731-NAV

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra Axxess XSVI-1731-NAV benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-