Metra AXDIS-PO13 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra AXDIS-PO13 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
AXDIS-PO13
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 10/4/21 INSTAXDIS-PO13
ATTENTION! With the key out of the
ignition, disconnect the negative battery
terminal before installing this product. Ensure
that all installation connections are secure
before cycling the ignition to test this product.
NOTE: Refer to the instructions included with
the aftermarket radio.
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Wire cutter
• Crimp tool and connectors
(ex. butt splice connectors, bellcaps, etc.)
or
• Solder gun, solder, and heat shrink
• Tape
• Zip-ties
TABLE OF CONTENTS
Connections ............................................................2
Installing the AXDIS-PO13 interface ...................... 3
Installing the Fiber Optic Cable.............................3
Programming the AXSWC interface .....................4
Data Interface with SWC
Porsche (with MOST 25 amp) 2010-2016
APPLICATIONS
Provides accessory power
Retains RAP
(retained accessory power)
Designed for MOST fiber
amplified system
Retains reverse camera
Micro-B USB updatable
Provides NAV outputs (parking
brake, reverse, speed sense)
Retains steering wheel controls
Retains balance
Porsche
Panamera 2010-2016 PCM 3.1
Cayenne 2012-2016 PCM 3.1
911 (991) 2012-2016 PCM 3.1
2008-up
Pontiac
Xxxxxxx 2007-2008
Xxxxxxx 2009
AXDIS-PO13 interface • AXDIS-PO13 harness • AXDIS-PO13 MOST-25 amplifier interface • AXSWC harness • AXSWC interface
• Female 3.5mm connector with stripped leads
Visit axxessinterfaces.com for more detailed information about the product and up-to-date
vehicle specific applications
2
CONNECTIONS
From the AXDIS-PO13 harness to the aftermarket radio, connect as indicated:
wire to the ground wire.Black
Yellow wire to the battery wire
wire to the power antenna wire.Blue
wire to the amp turn on wire.Blue/White
wire to the mute wire.Brown
wire to the illumination.Orange
wire to the accessory wire.Red
NOTE: There will an accessory wire from the Steering Wheel Control harness to connect as well.
The following (3) wires are only for multimedia/navigation radios that require these wires.
wire to the VSS/speed sense wire.Blue/Pink
wire to the reverse wire.Green/Purple
wire to the parking brake wire.Light Green
Tape off and disregard the following (8) wires, they will not be used in this application:
Gray, Gray/Black, Green, Green/Black, Purple, Purple/Black, White, White/Black
Connect the and RCA jacks to the front amplifier output jacks of the Red White
aftermarket radio.
From the AXSWC harness to the aftermarket radio:
This harness is only to be used if the vehicle is equipped with steering wheel controls.
Connect the wire to the accessory wire.Red
For the radios listed below: Connect the female 3.5mm connector with stripped leads to the
male 3.5mm SWC jack from the Steering Wheel Control harness. Tape off and disregard
remaining wires.
Connect the SWC wire, Eclipse: Brown Brown/White to the wire of the connector. Then
connect the remaining SWC wire, Brown/White Brown to the wire of the connector.
Connect the SWC Metra OE:
(Key 1)
wire to the wire.Gray Brown
Kenwood or select JVC with a SWC wire: Blue/Yellow Brown Connect the wire to the wire.
NOTE: Kenwood If the radio auto detects as a , manually set the radio type to JVC Kenwood.
See the instructions under changing radio type.
Connect the SWC XITE:
(SWC-2)
wire from the radio to the Brown wire.
Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold
separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio.
NOTE: The radio must be updated to rev. 2.1.4 or higher software.
Universal “2 or 3 wire” radio: Connect the SWC wire,
(Key-A or SWC-1)
to the Brown wire
of the connector. Then connect the remaining SWC wire,
(Key-B or SWC-2)
to the Brown/White
wire of the connector. If the radio comes with a third wire for ground, disregard this wire.
NOTE: After the interface has been programmed to the vehicle, refer to the manual provided with
the radio for assigning the SWC buttons. Contact the radio manufacturer for more information.
For all other radios: Connect the 3.5mm jack into the port on the radio designated for an
external SWC interface. Refer to the manual provided with the radio if in doubt as to
where the 3.5mm jack connects.
Adding aftermarket camera: YellowConnect the female RCA cable from the aftermarket camera
to the male RCA video wire.
Then
plug the Yellow male RCA video wire into the reverse camera
input of the aftermarket radio.
3
REV. 10/4/21 INSTAXDIS-PO13
Installing the AXDIS-PO13 Interface:
With the key in the off position:
Connect the AXDIS-PO13 harness to the AXDIS-PO13 interface.
Connect the AXDIS-PO13 harness to the AXDIS-PO13 MOST amplifier interface.
Connect the AXDIS-PO13 harness to the wiring harness in the vehicle.
Connect the USB retention harness from the vehicle to the aftermarket radio.
Connect the AXSWC harness to the AXSWC interface, and then to the AXDIS-PO13 interface.
Installing the Fiber Optic Cable:
Removal of the original fiber optic connection is required to adapt to the Media Oriented
System Transport (MOST) interface. The black connector housing uses a different keyway than
the MOST interface.
From the original Fiber Optic Connector: Using a pick tool, carefully pull this tab towards
the outside edge for the connector housing. Gently remove the
fiber optic insert from the
connector. (Figure A)
From the MOST Interface: Using the same steps from above, remove the gray insert from the
black fiber optic housing. Replace the gray connector with the fiber optic cables into the MOST
interface’s black connector housing. (Figure B)
Plug the MOST connector into the fiber decoder box.
INSTALLATION
(Figure A) (Figure B)


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: AXDIS-PO13

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra AXDIS-PO13 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-