Metra AX-MC90082 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra AX-MC90082 (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
AX-MC90082
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 4/28/20 INSTAX-MC90082
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell
caps, etc.)
TABLE OF CONTENTS
Connections ............................................................2
Installation .............................................................3
Programming .........................................................3
Mercedes ML (W164) (with M.O.S.T. 25 amplifier)
Data Interface with SWC 2005-2011
Mercedes GL (X164) (with M.O.S.T. 25 amplifier)
Data Interface with SWC 2006-2010
Provides accessory power
Retains R.A.P. (retained accessory power)
Designed for amplified models
Provides NAV outputs (parking brake, reverse, speed sense)
Retains audio controls on the steering wheel
Retains balance
Micro-B USB updatable
AX-MC90082 interface
AX-MC90082 amplifier interface
ASWC-1 interface
AX-MC90082 harness
ASWC-1 harness
Female 3.5mm connector with stripped leads
2
CONNECTIONS
From the aftermarket radio to the AX-MC90082 harness:
Connect the wire to the ground wire.Black
Connect the Yellow wire to the battery wire.
Connect the wire to the accessory wire.Red
If the aftermarket radio has an illumination wire, connect the wire to it.Orange
Connect the wire to the amp turn on wire of the new radio. *Blue
* wire triggers the factory antenna booster as well as the fiber-optic box.Blue
Connect the Brown wire to the mute wire.
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the wire to the VSS/speed sense wire.Blue/Pink
Connect the wire to the reverse wire.Green/Purple
Connect the wire to the parking brake wire.Light Green
Tape off and disregard the following (8) wires, they will not be used in this application:
Gray, Gray/Black Green Green/Black Purple Purple/Black White White/Black, , , , , ,
Connect the and RCA jacks to the front amplifier output jacks of the aftermarket radio.Red White
From the aftermarket radio to the ASWC-1 harness:
This harness is only to be used if the vehicle is equipped with steering wheel controls.
Connect the wire to the accessory wire.Red
For the radios listed below, connect the
female 3.5mm connector with stripped leads
, to
the
male 3.5mm SWC jack from the ASWC-1 harness. Any remaining wires tape off and disregard
:
Connect the steering wheel control wire, normally Eclipse: Brown Brown/, to the
White wire of the connector. Then connect the remaining steering wheel control wire,
normally , to the wire of the connector.Brown/White Brown
Connect the steering wheel control Key 1 wire (Gray) to the Metra OE: Brown wire.
Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow
wire to the wire.Brown
XITE:
Connect the steering wheel control SWC-2 wire from the radio to the wireBrown
.
Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold
separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio
.
Note:
The radio must be updated to rev. 2.1.4 or higher software.
Universal “2 or 3 wire” radio:
Connect the steering wheel control wire, referred to as
Key-A or SWC-1, to the
Brown
wire of the connector. Then connect the remaining
steering wheel control wire, referred to as Key-B or SWC-2, to the
Brown/White
wire of
the connector. If the radio comes with a third wire for ground, disregard this wire.
Note:
After the interface has been programmed to the vehicle, refer to the manual
provided with the radio for assigning the SWC buttons. Contact the radio manufacturer
for more information.
For all other radios: Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the
aftermarket radio designated for an external steering wheel control interface. Please refer to
the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.
3
REV. 4/28/2020 INSTAX-MC90082
With the key in the off position:
Connect the AX-MC90082 harness to the AX-MC90082 interface.
Connect the AX-MC90082 harness to the AX-MC90082 amplifier interface.
Remove the dust cover from fiber optic port in the AX-MC90082 amplifier interface.
Connect the factory fiber optic cable into the AX-MC90082 amplifier interface.
Connect the AX-MC90082 harness to the wiring harness in the vehicle.
Connect the ASWC-1 harness to the ASWC-1 interface, and then to the AX-MC90082 interface.
INSTALLATION
Press and hold the Volume-Up button on the steering wheel.
Turn the ignition on, the L.E.D. in the ASWC-1 interface will start flashing rapidly, which
means the ASWC-1 is looking for the vehicle and the radio.
Note:
If the L.E.D. did not start flashing rapidly, press the reset button for 3 seconds, while
still holding the Volume-Up button.
After a few seconds the L.E.D. should stop flashing rapidly, and then go out for approximately 2 seconds
.
After approximately 2 seconds there will be a series of 7 flashes, some short, and Green
some long. The long flashes represent the wires that are connected to the ASWC-1. The 3rd,
4th, 5th, and 6th flashes should be longer.
Tip:
Knowing this will help to troubleshoot, if need be.
The L.E.D. will pause for another 2 seconds, and then flash up to 18 times depending on Red
which radio is connected to the ASWC-1. Refer to the L.E.D. feedback section for information.
This is the end of the auto detection stage. Release from holding the Volume-Up button.
If the ASWC-1 detected the vehicle and the radio successfully, the L.E.D. will light up solid.
Test the steering wheel controls for proper operation. Refer to the ASWC-1 instructions online
at axxessinterfaces.com for customizing the buttons, if so desired.
PROGRAMMING
PROGRAMMING
(CONT.)
L.E.D. feedback
The (18) L.E.D. flashes represent what brand radio the ASWC-1 believes it is connected Red
to. Each flash represents a different radio manufacturer. For example, if you are installing
a JVC radio, the
ASWC-1
will flash (5) times. Following is a legend that dictates which
manufacturer corresponds to which flash.
L.E.D. feedback legend
* Note:
If the ASWC-1 flashes (7) times, and you do not have an Alpine radio connected Red
to it, that means the ASWC-1 does not detect a radio connected it. Verify that the 3.5mm
jack is connected to the correct steering wheel jack/wire in the radio.
** Note:
Part number AX-SWC-PARROT is required (sold separately). Also, the Parrot radio
must be updated to rev. 2.1.4 or higher through www.parrot.com.
Note:
If you have a Clarion radio and the steering wheel controls do not work, change the radio
type to the other Clarion radio type; same for Eclipse. The following section explains how to do this
.
Note:
If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC
radio, change the radio type to a Kenwood. The following section explains how to do this.
1 flash - Eclipse (Type 1) †
2 flashes - Kenwood ‡
3 flashes - Clarion (Type 1) †
4 flashes - Sony / Dual
5 flashes - JVC
6
flashes -
Pioneer / Jensen
7 flashes - Alpine *
8 flashes - Visteon
9 flashes - Valor
10 flashes - Clarion (Type 2) †
11 flashes - Metra OE
12 flashes - Eclipse (Type 2) †
13 flashes - LG
14 flashes - Parrot **
15 flashes - XITE
16 flashes - Philips
17 flashes - TBD
18 flashes - JBL


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: AX-MC90082

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra AX-MC90082 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-