Metra AX-BM90122 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra AX-BM90122 (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
AX-BM90122
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 11/13/19 INSTAX-BM90122
Product Info
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrinkTape • Wire cutter
• Zip ties
TABLE OF CONTENTS
Connections ............................................................2
Installation ............................................................. 3
Programming ......................................................... 3
BMW (with M.O.S.T. 25 amplifier) 2004-2013
Provides accessory power (12 volt 10 amp)
Retains R.A.P. (retained accessory power)
Designed for amplified models
Retains audio controls on the steering wheel
Retains phone buttons (radio dependent)
Retains factory features: date, time, temperature display
Micro-B USB updatable
AX-BM90122 interface
AX-BM90122 amplifier interface
ASWC-1 interface
AX-BM90122 harness
ASWC-1 harness
3.5mm adapter
APPLICATIONS
BMW
1-Series 2004-2013 3-Series 2005-2012
2
CONNECTIONS
From the aftermarket radio to the AX-BM90122 harness, connect the:
wire to the ground wire.Black
Yellow wire to the battery wire.
Yellow wire (6’ long w/ fuse-holder) directly to the vehicles battery.
wire to the accessory wire.Red
Orange wire to the illumination wire (if applicable).
wire to the power antenna turn-on wire.Blue
Brown wire to the mute wire.
The following (3) wires are only for multimedia/navigation radios that require these wires.
wire to the VSS/speed sense wire.Blue/Pink
Green/Purple wire to the reverse wire.
Light Green wire to the parking brake wire.
Tape off and disregard the following (8) wires, they will not be used in this application:
Gray, Gray/Black Green Green/Black Purple Purple/Black White White/Black, , , , , ,
and RCA jacks to the full range amplifier output jacks.Red White
ASWC-1 harness:
This harness is only to be used if the vehicle is equipped with steering wheel controls.
Connect the wire to the chassis ground.Black
Connect the wire to accessory power.Red
For the radios listed below: Connect the
3.5mm adapter
to the male 3.5mm SWC jack from the
ASWC-1 harness. Any remaining wires tape off and disregard:
Connect the steering wheel control wire, normally Eclipse: Brown Brown/White, to the wire
of the connector. Then connect the remaining steering wheel control wire, normally Brown/
White Brown, to the wire of the connector.
Connect the steering wheel control Key 1 wire to the Metra OE: (Gray) Brown wire.
Kenwood or select JVC with a steering wheel control wire: Blue/Yellow Connect the wire to
the wire.Brown
Connect the steering wheel control SWC-2 wire from the radio to the XITE: Brown wire.
Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold
separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio.
Note:
The radio must be updated to rev. 2.1.4 or higher software.
Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as Key-A or
SWC-1, to the Brown wire of the connector. Then connect the remaining steering wheel control
wire, referred to as Key-B or SWC-2, to the wire of the connector. If the radio Brown/White
comes with a third wire for ground, disregard this wire.
Note:
After the interface has been programmed to the vehicle, refer to the manual provided with
the radio for assigning the SWC buttons. Contact the radio manufacturer for more information.
Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the For all other radios:
aftermarket radio designated for an external steering wheel control interface. Please refer to the
aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.
3
REV. 11/13/2019 INSTAX-BM90122
With the key in the off position:
Connect the AX-BM90122 harness AX-BM90122 interface to the .
Connect the AX-BM90122 harness AX-BM90122 amplifier interface to the .
Remove the dust cover from fiber optic port in the AX-BM90122 amplifier interface.
Connect the factory fiber optic cable into the AX-BM90122 amplifier interface.
Connect the AX-BM90122 harness to the wiring harness in the vehicle.
Connect the ASWC-1 harness ASWC-1 interface to the , and then to the AX-BM90122 interface.
Press and hold the Volume-Up button on the steering wheel.
Turn the ignition on, the L.E.D. in the ASWC-1 interface will start flashing rapidly, which
means the ASWC-1 is looking for the vehicle and the radio.
Note:
If the L.E.D. did not start flashing rapidly, press the reset button for 3 seconds, while still
holding the Volume-Up button.
After a few seconds the L.E.D. should stop flashing rapidly, and then go out for
approximately 2 seconds.
After approximately 2 seconds there will be a series of 7 flashes, some short, and Green
some long. The long flashes represent the wires that are connected to the ASWC-1. The 3rd,
4th, 5th, and 6th flashes should be longer.
Tip:
Knowing this will help to troubleshoot, if need be.
The L.E.D. will pause for another 2 seconds, and then flash up to 18 times depending on Red
which radio is connected to the ASWC-1. Refer to the L.E.D. feedback section for information.
This is the end of the auto detection stage. Release from holding the Volume-Up button.
If the ASWC-1 detected the vehicle and the radio successfully, the L.E.D. will light up solid.
Test the steering wheel controls for proper operation. Refer to the ASWC-1 instructions online at
axxessinterfaces.com for customizing the buttons, if so desired
.
INSTALLATION
PROGRAMMING
PROGRAMMING
(CONT.)
L.E.D. feedback
The (18) L.E.D. flashes represent which brand radio the ASWC-1 is connected to. Each Red
flash represents a different radio manufacturer. For example, if you are installing a JVC radio,
the ASWC-1 will flash (5) times, and then stop. Following is a legend that dictates which Red
radio manufacturer corresponds to which ash.
L.E.D. feedback legend
1 flash - Eclipse (Type 1) †
2 flashes - Kenwood ‡
3 flashes - Clarion (Type 1) †
4 flashes - Sony / Dual
5 flashes - JVC
6
flashes -
Pioneer / Jensen
7 flashes - Alpine *
8 flashes - Visteon
9 flashes - Valor
10 flashes - Clarion (Type 2) †
11 flashes - Metra OE
12 flashes - Eclipse (Type 2) †
13 flashes - LG
14 flashes - Parrot **
15 flashes - XITE
16 flashes - Philips
17 flashes - TBD
18 flashes - JBL
* Note:
If the ASWC-1 flashes (7) times, and you do not have an Alpine radio connected to Red
it, that means the ASWC-1 does not detect a radio connected it. Verify that the 3.5mm jack is
connected to the correct steering wheel jack/wire in the radio.
** Note:
The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be
updated to rev. 2.1.4 or higher through www.parrot.com.
Note:
If you have a Clarion radio and the steering wheel controls do not work, change the radio type to
the other Clarion radio type; same for Eclipse. Refer to the “Programming Information” document online
.
Note:
If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC radio,
change the radio type to a Kenwood. Refer to the “Programming Information” document online
.


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: AX-BM90122

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra AX-BM90122 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-