Metra 99-9008 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 99-9008 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
REV. 1/25/2016 INST99-9008
Installation instructions for part 99-9008
CAUTION!
Metra recommends disconnecting the negative bat
-
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
• ISO DIN radio provision
• DIN radio provision
*
Aftermarket radios are equipped with a trim ring surrounding the face of
the radio. Since some installers prefer the trim ring equipped with the radio
(DIN) and others do not (ISO DIN), this kit was designed to allow the installer
to choose.
• A) ISO DIN housing • B) ISO DIN trim plate • C) ISO DIN brackets • D) DIN trim plate
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-1784
Antenna Adapter: • 40-VW54
• 86-9001 radio removal keys • Torx T-10 driver
TOOLS REQUIRED
Volkswagen Beetle 1998-2010
99-9008
A B C
Dash Disassembly ................................................. 2
Kit Assembly
– ISO DIN radio provision......................................... 3
– DIN radio provision............................................ 4
Table of Contents
D
99-9008
2
1. Insert the long end of the 86-9001
radio removal tool into the slots in
the factory radio (flat sides pointing
out), and then pull the radio out.
Disconnect all connectors and then
remove the radio. (Figure A)
2. For ISO DIN radio installations only,
remove (2) Torx T-10 screws exposed
in the radio cavity. (Figure A)
Continue to kit assembly
Dash Disassembly
(Figure A)
99-9008
ISO DIN radio provision
1. Remove the metal DIN sleeve and
trim ring from the aftermarket radio
.
2. Align the holes in the ISO DIN
brackets with the holes in the radio
and then secure the brackets to
the radio with the
screws included
with the radio. (Figure A)
Note: The screws provided with
certain radios may create a
clearance problem during radio
installation. In these cases it may
be necessary to trim the walls
of the dash bezel to provide the
proper clearance.
3. Locate the factory wiring harness
and antenna connector in the
dash and make all necessary
connections to the radio. Metra
recommends using the proper
mating adapters from Metra and/or
AXXESS. Re-connect the negative
battery terminal and test the radio
for proper operation.
4. Slide the radio into the radio cavity
until it clicks in. (Figure B)
5. Position the ISO DIN housing over
the radio with the side notches in
the upper corners. Secure with the
(2) Torx T-10 screws removed in
dash disassembly. (Figure C)
6. Attach the ISO DIN trim plate onto
the . (Figure D)ISO DIN housing
(Figure B) (Figure D)
(Figure A)
Kit Assembly
(Figure C)
3


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 99-9008

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 99-9008 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-