Metra 99-8910S Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 99-8910S (9 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/9
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 9/28/20 INST95-7638
I N S TA L L AT I O N I N S T R U C T I O N S
95-7638
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
ISO DDIN radio provision
Pioneer modular DDIN radio provision †
Painted with a gloss black face, silver trim, and a textured housing.
KIT COMPONENTS
• A) Radio housing (front) • B) Radio housing (rear) • C) Radio trim panel • D) Radio brackets • E) Pioneer adapter brackets
• F) #4 x 3/8” Phillips screws (4) • G) #6 x 3/8” Phillips screws (4) • H) Panel clips (3) TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 10mm socket wrench
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly
– ISO DDIN radio provision ................................3-4
– Pioneer modular DDIN radio provision.........5-6
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-7552
Antenna Adapter: 40-NI12
A B C
F G
D E
Nissan Sentra 2020-Up
H
Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com
specific applications
† This kit can only be used with an ISO DDIN radio with an “L” shaped chassis design, with the radio
chassis at the bottom of the screen. As of this writing, only the Alpine INE-W967HD (discontinued,
replaced by INE-W977HD), iLX-107, and iLX-207 have this design. Also, The Pioneer modular radios,
DMH-C2550NEX and DMH-C2500NEX, can also be used with the included adapter brackets.
2386.257.1187
|
MetraOnline.com
1. Unclip and remove the trim panel
behind the radio. There are (4) clips
securing this panel to the dash. Use
caution as the front of the trim panel
can easily be damaged. (Figure A)
Dash vents may vary depending Note:
on Nissan model.
2. Remove (4) 10mm screws securing the
radio. Take note that the lower radio
brackets are angled inward, hiding the
bottom (2) screws from being easily
seen. Slide the radio out, then unplug
and remove the radio. (Figure B)
Continue to Kit Assembly
(Figure A) (Figure B)
DASH DISASSEMBLY
REV. 9/28/2020 INST95-7638 3
KIT ASSEMBLY
ISO DDIN radio provision
1. Attach (3) provided onto the panel clips
radio housing (front). (Figure A)
2. Snap the radio housing (front) to the
radio housing (rear), then secure using
(4) #4 x 3/8” Phillips screws provided
(Figure B)
3. radio brackets Secure the to the radio
housing using (4) #6 x 3/8” Phillips
screws provided. (Figure C)
Continued on the next page
(Figure A) (Figure B) (Figure C)


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 99-8910S

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 99-8910S benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-