Metra 99-7617GHG Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Metra 99-7617GHG (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
INSTALLATION INSTRUCTIONS FOR PART 99-7617GHG
APPLICATIONS
METRA. The World’s best kits.™metraonline.com1-800-221-0932 © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
REV. 4/3/2013 INST99-7617GHG
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
Table of Contents
• ISO DIN radio provision with pocket
• Painted Grey High Gloss
• A) Radio Trim Panel • B) Radio Brackets • C) Pocket • D) (4) #8 x 3/8” Phillips Pan Head Screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7552 2010-Up Nissan Wire Harness • 70-7554 2010-Up Nissan Wire Harness
Antenna Adapter: • 40-NI12 2010-Up Nissan Antenna Adapter
• Panel removal tool • Phillips screwdriver • Socket Wrench
TOOLS REQUIRED
(Sedan)
A B C D
Dash Disassembly
– Nissan Altima 2013-up ......................................... 2
Kit Assembly
– ISO DIN radio provision with pocket ....................... 3
99-7617GHG
1. Unclip the right side of the driver’s
knee bolster panel next to the
center console and let hang. Note:
There is no need to completely
remove the panel. (Figure A)
2. Unclip and remove the (2) silver
side trim panels from each side of
the factory radio. (Figure B)
3. Unclip and remove trim panel
below the a/c control panel.
Dash Disassembly
(Figure A)
(Figure D)
(Figure B)
(Figure E)
(Figure C)
(Figure F)
4. Remove (4) Phillips screws
securing the factory radio, a/c
control and a/c vents. (Figure C)
5. Remove the a/c controls.
(Figure D)
6. Remove the a/c vent panel.
(Figure E)
7. Remove the factory radio.
(Figure F)
8. If equipped there may be an a/c
amp present attached under the
radio remove (2) Phillips screws
securing the a/c amp.
Continue to kit assembly
99-7617GHG
Kit Assembly
ISO DIN radio provisions with pocket
1. If equipped attach the a/c amp to
the radio brackets with the factory
hardware. (Figure A)
2. Mount the pocket to the radio
brackets with the (4) #8 X 3/8”
Phillips pan head screws supplied.
(Figure A)
3. Slide the head unit into radio
brackets and secure with screws
supplied with the unit.
(Figure B)
4. Locate the factory wiring harness
and antenna plug in the dash.
Metra recommends using the
proper mating adapters from Metra
and/or AXXESS.
5. Reassemble dash in reverse order
of disassembly.
(Figure A) (Figure B)


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 99-7617GHG

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 99-7617GHG benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-