Metra 99-3017B Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 99-3017B (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2015 METRA ELECTRONICS CORPORATION
REV. 11/17/2015 INST99-3017B
CAUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
Installation instructions for part 99-3017B
A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws
20;*64765,5;:
>0905.(5;,55(*655,*;065: (sold separately)
Wiring Harness: • LC-GMRC-044 or AX-ADBOX2 and AX-ADGM04
Antenna Adapter: 40-EU55
Panel removal tool • Phillips screwdriver
• Socket wrench
;663:9,8<09,+
Chevrolet Trax 2015-up
99-3017B
A DCB
Dash Disassembly ................................................. 2
Kit Assembly
ISO DIN radio provision with pocket ...................... 3
Table of Contents
ISO DIN radio provision with pocket
Painted to match factory finish
20;-,(;<9,:
99-3017B
2
Dash Disassembly
1. Unclip and remove the panel
surrounding the factory radio
including the a/c vents. (Figure A)
2. Remove (4) 9/32” screws securing
the radio chassis. (Figure B)
3. Remove (2) screws securing the
a/c vents to the factory radio trim
panel and keep for kit assembly.
(Figure C)
4. Unclip and remove the (9) metal
panel clips from the factory panel
and keep them for kit assembly.
5. Unclip and remove the (2) small
pockets on either side of the a/c
vents and keep for kit assembly.
(Figure D)
Note: Remember the process
when removing these pockets
as you will need to reinstall
them into the 99-3017B radio
panel the same way.
Continue to kit assembly
(Figure A) (Figure C)
(Figure B) (Figure D)
99-3017B
3
Kit Assembly
(Figure A)
(Figure B)
ISO DIN radio provision with pocket
1. Clip the (2) small pockets into the
99-3017B .radio trim panel
2. Attach the (9) metal panel clips to
the 99-3017B .radio trim panel
3. Attach the a/c vents to the
99-3017B with radio trim panel
the factory hardware.
4. Secure the radio brackets to the
pocket with (4) #8 x 3/8 Phillips
screws supplied. (Figure A)
5.
Remove the metal “DIN sleeve and
trim ring from the aftermarket radio.
6. Secure the radio to the completed
assembly using the screws
supplied with the radio. (Figure B)
7. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Re-connect the negative
battery terminal and test the radio
for proper operation.
8. Mount the new radio assembly into
the dash and reassemble the dash
in reverse order of disassembly
using the 99-3017B radio
trim panel.


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 99-3017B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 99-3017B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-