Metra 95-8909 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 95-8909 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/5/18 INST95-8909
I N S TA L L A T I O N I N S T R U C T I O N S
95-8909
KIT FEATURES
• ISO DDIN radio provision
• Painted black with silver trim
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) (4) Panel clips
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ....................................................... 3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1761 (non-amplied models)
Antenna Adapter: 40-LX11
Steering wheel control interface: Please visit
axxessinterfaces.com for more information
A B C
Subaru Legacy/Outback (all except 2.5i) 2018-up*
*Visit MetraOnline.com for up-to-date vehicle specic applications.
1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unclip and remove the trim below the
climate control panel. (Figure A)
2. Remove (2) Phillips screw securing
the climate control panel, then unclip,
unplug, and remove the panel.
(Figure B)
(Figure B)
(Figure A)
3. Unclip and remove the a/c vent panel.
(Figure C)
Tip! Start from the bottom of the panel
and release the bottom (2) clips rst.
4. Remove (4) Phillips screws securing the
radio, then unclip, unplug and remove
the radio. (Figure D, E)
Continue to Kit Preparation
(Figure C)
(Figure D)
(Figure E)
Upper screws
Lower screws
REV. 4/5/2018 INST95-8909 3
KIT PREPARATION KIT ASSEMBLY
1. Secure the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
2. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra and/
or Axxess. Test the radio for
proper operation.
3. Secure the radio assembly to the dash
using the factory screws.
4. Attach the
(4) panel clips
provided onto
the
radio trim panel
, then snap the
panel over the radio assembly.
5. Reassemble the dash in reverse
order of disassembly to complete the
installation.
(Figure A)
1. Slightly loosen (4) screws securing
the radio. (Figure A)
2. If the vehicle is equipped with Starlink,
remove (4) screws securing the Starlink
module (shaded part in gure A) located
directly below the radio. The module
must be relocated lower in the dash
cavity to retain functionality with the
front speakers. (Figure A)
3. Remove (4) screws securing the lower
module, then remove the module.
(Figure A)
4. Secure the module to the
radio brackets
using the factory screws. (Figure B)
Continue to Kit Assembly
(Figure B)
(Figure A)


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 95-8909

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 95-8909 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂźr -Kategorien-