Metra 95-8721B Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 95-8721B (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
REV. 5/13/2016 INST95-8721B
Table of Contents
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
Installation instructions for part 95-8721B
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
• Double DIN radio provision
Painted matte black
A) Radio housing trim panel • B) BracketsC) (4) #8 x 3/8 Phillips screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • XSVI-9005-NAV
Antenna Adapter: • 40-EU10
• Panel removal tool • Phillips screwdriver • Socket wrench Torx driver
TOOLS REQUIRED
A B C
Dash Disassembly .............................................. 2-3
Kit Assembly
Double DIN radio provision 3 ...................................
95-8721B
1. Unclip and remove cover around
shift lever and cup holder.
(Figure A)
2. Unclip and remove ashtray
assembly. (Figure B)
3. Remove (2) Torx screws from the
bottom of the climate control unit
then remove the unit. (Figure C)
Dash Disassembly
AUTO A/C
FR
ONT REAR
72
64 80
F
80
72
64
4
5
6
F
AUTO A/C
FR
ON
TREAR
72
64 80
F
80
72
64
3
2
4
5
6
F
AUTO A/C
FRO
NT REAR
72
64
80
F
80
72
64
3
2
4
5
6
F
(Figure A)
(Figure D)
(Figure B)
(Figure C)
4. Inside each vent, using a small
flat screwdriver push the lower
tab inward toward the center of
the vent and then rotate each vent
up to expose (1) Torx head screw.
Loosen the Torx screws (It is not
necessary to remove the screws.) Push
the upper clip inward and rotate the
vent downward to expose (1) spring
clip in the top of the vent assembly.
(Figure D)
Continued on next page
95-8721B
ES P
OFF
AUT
OA
FRONT
72
64
80
F
80
72
64
3
2
4
5
6
F
(Figure E)
(Figure F)
(Figure G)
Kit AssemblyDash Disassembly
Double DIN radio provision
1. Attach the brackets to the radio
housing trim panel trim plate with
the supplied #8 x 3/8” screws.
(Figure A)
2. From the back, slide the Double
DIN radio into the bracket/radio
housing assembly and secure
using the screws supplied with the
radio. (Figure B)
3. Locate the factory wiring harness
and antenna plug in the dash.
Metra recommends using the
proper mating adapters from
Metra and/or AXXESS.
4. Reassemble dash in reverse order
of disassembly.
5. Unclip and remove the vent
assembly. (Figure E)
6. Unclip and remove the push button
panel above the radio (Figure F)
7. Remove (4) Torx screws securing
factory radio then remove the unit.
(Figure G)
8. Remove the two metal clips on the
bottom of the factory radio and
place them on the bottom tabs of
the radio housing trim panel.
Continue to kit assembly
(Figure A)
(Figure B)


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 95-8721B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 95-8721B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-