Metra 95-7377B Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 95-7377B (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
REV. 1/24/2017 INST95-7377B
INSTALLATION INSTRUCTIONS FOR PART 95-7377B
METRA – The World’s best kits.®metraonline.com © COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
CAUTION!
All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
ISO DDIN radio provision
Painted matte black
A) Radio trim panel • B) Radio brackets C) (2) Panel clips
20;-,(;<9,:
20;*64765,5;:
>0905.(5;,55(*655,*;065: (sold separately)
Wiring Harness: • 70-7304 Antenna Adapter: Not required
Panel removal tool • Phillips screwdriver
;663:9,8<09,+
Kia Optima 2016-up
95-7377B
Table of Contents
A B C
Dash Disassembly ................................................. 2
Kit Preparation ....................................................... 3
Kit Assembly .......................................................... 3
95-7377B
2
Dash Disassembly
1. Open the glove box and remove the
trim at the top of the opening, and
then remove the (2) Phillips screws
exposed. (Figure A)
2. Unclip the trim that runs along the
dash from the right side A/C vent
to the steering column, and then
remove the (2) Phillips screws
securing the A/C vent/hazard panel.
(Figure B)
3. Unclip and remove the right side
trim panel from the center console,
and then remove the (1) Phillips
screw securing the A/C vent/hazard
panel. (Figure C)
4. Unclip the A/C vent/hazard panel,
disconnect the hazard switch, and
then remove the panel. (Figure D)
5. Using caution not to break the
panel, carefully unclip and remove
the radio trim panel. (Figure D)
(Figure B)
(Figure D)
(Figure E)
(Figure A) (Figure C)
Note: There are (8) clips that attach
the panel to the vehicle: (2) at
the top-middle, (2) at the bottom
corners, (2) at the top corners, and
(2) in the center (these 2 are only in
non-nav models). (Figure E)
6. Remove the (4) Philips screws
securing the radio and then remove.
Continue to Kit Preparation
95-7377B
3
(Figure A)(Figure A)
Kit AssemblyKit Preparation
ISO DDIN radio provision
1. Attach the radio brackets to the
radio using the screws supplied
with the radio. (Figure A)
2. Locate the factory wiring harness
and connector in the dash and
complete all necessary connections
to the radio. Metra recommends
using the proper mating adapter
from Metra and/or Axxess. Test the
radio for proper operation.
3. Secure the completed assembly into
the dash using the factory screws.
4. Snap the radio trim panel over the
completed assembly, and then
reassemble the dash in reverse
order of disassembly.
1. Attach the (2) to thepanel clips
radio trim panel as shown.
(Figure A)
Continue to Kit Assembly


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 95-7377B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 95-7377B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-