Metra 95-6554B Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 95-6554B (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 11/12/19 INST95-6554B
I N S TA L L AT I O N I N S T R U C T I O N S
95-6554B
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
• ISO DDIN radio provision
• Complete panel for a factory look and feel
• Painted scratch resistant matte black
KIT COMPONENTS
• A) Radio dash panel • B) Radio brackets • C) Phillips screw • D) Tape (not shown)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Cutting tool • 1/8” drill bit • 3/8” socket set
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ...................................................3-4
Kit Assembly ..........................................................5
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1817
Antenna Adapter: Not required
A B C
Jeep Cherokee 1997-2001
Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com
specic applications
1.800.221.0932
|
MetraOnline.com
2
1. Unclip and remove the radio trim panel.
Remove the factory panel clips and A/C
vents for re-use in Kit Assembly.
(Figure A)
2. Remove (2) 3/8” screws securing the
radio. Slide the radio out, then unplug
and remove.
Continue to Kit Preparation
(Figure A)
DASH DISASSEMBLY
REV. 11/12/2019 INST95-6554B 3
KIT PREPARATION
Attention! The sub-dash of the vehicle
will have to be cut to allow room for the
aftermarket radio. Once cut, the factory radio
will no longer be able to be re-installed. Also
take note that the radio sub-dash is actually
the a/c vents for the vehicle. After the
sub-dash has been cut, the tape provided
will have to be used to cover up the holes to
prohibit air from leaking out.
For select Sony radios* with an “L” shaped
chassis design:
1. Remove (4) Phillips screws securing
the climate controls. Partially slide the
controls out and move down slightly.
2. Cut the sub-dash to allow room for the
aftermarket radio. (Figure B)
3. Apply tape over the area cut. (Figure C)
4. Cut the radio brackets as shown.
(Figure D)
5. Secure the climate controls back to the
vehicle using just the (2) lower screws.
The upper screws will be reused in
Kit Assembly.
* At present (9-12-19), models XAV-AX100,
XAV-AX1000, XAV-AX200, XAV-A500, and
XAV-V10BT have this design
Continue to Kit Assembly
(Figure A) (Figure C)
(Figure D)
Remove shaded area
Remove shaded area
Tape over the cut area
(Figure B)


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 95-6554B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 95-6554B benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂźr -Kategorien-