Metra 92-3056P Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Metra 92-3056P (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
IMPORTANT
Installation Kit
120 92-3056P
Before starting, compare items on your invoice with items
received. Carefully check through packaging material.
If an item is missing, please call:
Crutchfield
Parts Supplied:
Kit Frame
Support Tray
Chevrolet
Revision 09/18/03
Kit assembly instructions are on the following pages.
Page 1 of 3
®
Copyright 2003 Crutchfield Corporation
*120923056P*
Mounting Bracket (2) Studs (2) 3/8” Nuts
(4) 1/4” Hex Screws
Trimplate
at 1-888-955-6000
FIGURE 2
Shaft Supports
Installation Kit
Tools Required
120 92-3056P
Chevrolet
1. Press posts on trimplate into holes on kit frame to snap
parts together and secure with hex screws (Figure 1).
2. Use a utility knife to cut out in trimplate to shaft supports
create a DIN opening (Figure 2).
3. Push clips on into slots on rear of kit frame tosupport tray
secure (Figure 1).
4. Secure mounting bracket to bottom of kit frame with
studs nutsand supplied (Figure 1).
5. Remove DIN sleeve from receiver and slide into opening
in trimplate. Secure sleeve to trimplate by bending the
securing tabs (Figure 3).
6. Slide receiver into sleeve/kit assembly.
DIN Receiver Assembly
Utility
Knife
2
®
Copyright 2003 Crutchfield Corporation
FIGURE 3
Securing Tabs
DIN Sleeve
Bend tabs after sleeve
is inside assembly.
â–˛
Small Flat Blade
Screwdriver
FIGURE 1
Trimplate
Kit Frame
Support Tray
Mounting Bracket
Stud
Nut
1/4” & 3/8”
Sockets
Hex Screws
Installation Kit
120 92-3056P
Chevrolet
Spacers
(supplied with
your order)
1. Press posts on trimplate into holes on kit frame to snap parts
together and secure with hex screws (Figure 1).
2. Push clips on into slots on rear of kit frame to support tray
secure (Figure 1).
3. Secure mounting bracket to bottom of kit assembly with
studs nutsand supplied (Figure 1).
4. Choose the proper spacers (supplied with your order) to
allow receiver nosepiece to extend 1/8” to 1/4” beyond face of
trimplate (Figure 2).
5. Insert receiver shafts (with spacers in place) through openings
in trimplate. Secure receiver and faceplate with shaftnuts
supplied with receiver.
6. Attach control knobs.
1/8” -1/4”
â–˛
â–˛
Spacer
Shaft Receiver Assembly
3
FIGURE 2
Shaftnuts
®
Copyright 2003 Crutchfield Corporation
FIGURE 1
Trimplate
Kit Frame
Support Tray
Mounting Bracket
Faceplate
Control Knobs
Tools Required
â–˛
Deep Socket
(size depends upon receiver)
Stud
Nut
1/4” & 3/8”
Sockets
Hex Screws


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 92-3056P

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 92-3056P benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-