Metra 92-3042P Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Metra 92-3042P (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
IMPORTANT
Installation Kit
120 92-3042P
Before starting, compare items on your invoice with items
received. Carefully check through packaging material.
If an item is missing, please call:
Crutchfield
Parts Supplied:
Kit Frame
Support Tray
Chevrolet
Revision 09/17/03
Kit assembly instructions are on the following pages.
Page 1 of 3
®
Copyright 2003 Crutchfield Corporation
*120923042P*
Mounting Brackets
Left
Right
(2) Studs (2) 3/8” Nuts
(4) 1/4” Hex Screws
Trimplate
at 1-888-955-6000
FIGURE 2
Shaft Supports
Installation Kit
120 92-3042P
Chevrolet
1. Press posts on trimplate into holes on kit frame to snap
parts together and secure with hex screws (Figure 1).
2. Use a utility knife to cut out in trimplate to shaft supports
create a DIN opening (Figure 2).
3. Push clips on into slots on rear of kit frame to support tray
secure (Figure 1).
4. Select the . Break off the tabs right side mounting bracket
that are shown as shaded (Figure 3).
5. Secure mounting brackets to sides of kit frame with studs
and nuts supplied (Figure 1).
6. Remove DIN sleeve from receiver and slide into opening in
trimplate. Secure sleeve to trimplate by bending the
securing tabs (Figure 4).
7. Slide receiver into sleeve/kit assembly.
DIN Receiver Assembly
2
®
Copyright 2003 Crutchfield Corporation
Securing Tabs
DIN Sleeve
Bend tabs after sleeve
is inside assembly.
FIGURE 1
Trimplate
Kit Frame
Support Tray
Left Mounting Bracket
Stud
Nut
Right Mounting Bracket
FIGURE 3
FIGURE 4
Break off only
shaded tabs
Hex Screws
Right Side
Mounting Bracket
Tools Required
Utility
Knife
â–˛
Small Flat Blade
Screwdriver
3/8” Socket
Pliers
Installation Kit
120 92-3042P
Chevrolet
Spacers
(supplied with
your order)
1. Press posts on trimplate into holes on kit frame to snap parts
together and secure with hex screws (Figure 1).
2. Push clips on into slots on rear of kit frame support tray
to secure (Figure 1).
3. Select the . Break off all tabs right side mounting bracket
shown as shaded (Figure 2).
4. Secure mounting brackets to sides of kit assembly with studs
and nuts supplied (Figure 1).
5. Choose the proper spacers (supplied with your order) to
allow receiver nosepiece to extend 1/8” to 1/4” beyond face of
trimplate (Figure 3).
6. Insert receiver shafts (with spacers in place) through openings
in trimplate. Secure receiver and faceplate with shaftnuts
supplied with receiver.
7. Attach control knobs.
1/8” -1/4”
â–˛
â–˛
Spacer
Shaft Receiver Assembly
3
FIGURE 3
Shaftnuts
®
Copyright 2003 Crutchfield Corporation
FIGURE 1
Trimplate Kit Frame
Support Tray
Left Mounting Bracket
Faceplate
Control Knobs
Tools Required
â–˛
Deep Socket
(size depends upon receiver)
Stud
Nut
Right Mounting Bracket
FIGURE 2
Break off only
shaded tabs
1/4” & 3/8”
Sockets
Hex Screws
Right Side
Mounting Bracket
Pliers


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 92-3042P

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 92-3042P benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-