Metra 91-3300P Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Metra 91-3300P (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
IMPORTANT
Installation Kit
120 91-3300P
Before starting, compare items on your invoice with items
received. Carefully check through packaging material.
If an item is missing, please call:
Crutchfield
Parts Supplied:
Kit Frame
Support Tray
Chevrolet
Revision 10/29/03
Kit assembly instructions are on the following pages.
(2) Studs
Page 1 of 3
®
Copyright 2003 Crutchfield Corporation
*120913300P*
Trimplate
(2) 3/8” Nuts
Mounting Brackets
(4) 1/4” Hex Screws
at 1-888-955-6000
FIGURE 2
Shaft Supports
Installation Kit
Tools Required
120 91-3300P
Chevrolet
1. Press posts on trimplate into holes on kit frame to
snap parts together and secure with hex screws
(Figure 1).
2. Use a utility knife to cut out shaft supports in
trimplate to create a DIN opening (Figure 2).
3. Push clips on into slots on rear of kit support tray
frame to secure (Figure 1).
4. Secure side to kit frame with mounting brackets
studs nutsand supplied (Figure 1).
5. Remove DIN sleeve from receiver and slide into
opening in trimplate. Secure sleeve to trimplate by
bending the securing tabs (Figure 3).
6. Slide receiver into sleeve/kit assembly.
DIN Receiver Assembly
Utility
Knife
2
®
Copyright 2003 Crutchfield Corporation
FIGURE 3
Securing Tabs
DIN Sleeve
Bend tabs after sleeve
is inside assembly.
â–˛
Small Flat Blade
Screwdriver
FIGURE 1 Trimplate
Kit Frame
Support Tray
Mounting Bracket
Mounting Bracket
Stud Nut
1/4” & 3/8”
Sockets
Hex Screws
Installation Kit
120 91-3300P
Chevrolet
Spacers
(supplied with
your order)
1. Press posts on trimplate into holes on kit frame to
snap parts together and secure with hex screws
(Figure 1).
2. Push clips on into slots on rear of kit framesupport tray
to secure (Figure 1).
3. Secure side to kit assembly with mounting brackets
studs nutsand supplied (Figure 1).
4. Choose the proper spacers (supplied with your order) to
allow receiver nosepiece to extend 1/8” to 1/4” beyond
face of trimplate (Figure 2).
5. Insert receiver shafts (with spacers in place) through
openings in trimplate. Secure receiver and faceplate
with shaftnuts supplied with receiver.
6. Attach control knobs.
1/8” -1/4”
â–˛
â–˛
Spacer
Shaft Receiver Assembly
3
FIGURE 2
Shaftnuts
®
Copyright 2003 Crutchfield Corporation
FIGURE 1
Trimplate
Kit Frame
Support Tray
Mounting Bracket
Mounting Bracket
Faceplate
Control Knobs
Tools Required
â–˛
Deep Socket
(size depends upon receiver)
Stud
Nut
1/4” & 3/8”
Sockets
Hex Screws


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 91-3300P

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 91-3300P benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-