Metra 90-3044P Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Metra 90-3044P (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
IMPORTANT
Installation Kit
120 90-3044P
Before starting, compare items on your invoice with items
received. Carefully check through packaging material.
If an item is missing, please call:
Crutchfield
Parts Supplied:
Kit Frame
Support Tray
Chevrolet/GMC
Revision 09/17/03
Kit assembly instructions are on the following pages.
(2) Studs
Page 1 of 3
®
Copyright 2003 Crutchfield Corporation
*120903044P*
Trimplate
(2) 3/8” Nuts
Mounting Brackets
at 1-888-955-6000
FIGURE 2
Shaft Supports
Installation Kit
120 90-3044P
1. Press posts on trimplate into holes on kit frame to snap
parts together and secure (Figure 1).
2. Use a utility knife to cut out in trimplate to shaft supports
create a DIN opening (Figure 2).
3. Push clips on into slots on rear of kit frame to support tray
secure (Figure 1)
4. Cut off all the tabs labeled “A” “B”and on both mounting
brackets that are shown as shaded (Figure 3). The “C” tabs
should be the only remaining tabs.
5. Secure side mounting brackets to kit frame with studs and
nuts supplied (Figure 1).
6. Remove DIN sleeve from receiver and slide into opening in
trimplate. Secure sleeve to trimplate by bending the securing
tabs (Figure 4).
7. Slide receiver into sleeve/kit assembly.
DIN Receiver Assembly
2
®
Copyright 2003 Crutchfield Corporation
FIGURE 4
Securing Tabs
DIN Sleeve
Bend tabs after sleeve
is inside assembly.
FIGURE 1 Trimplate
Kit Frame
Support Tray
Mounting Bracket
Mounting Bracket
Stud Nut
Chevrolet/GMC
Tools Required
Utility
Knife
â–˛
Small Flat Blade
Screwdriver
3/8” Socket
FIGURE 3
Cut off A & B
(shaded tabs)
on both brackets
These “C” tabs must remain
Hacksaw
Installation Kit
120 90-3044P
Spacers
(supplied with
your order)
1. Press posts on trimplate into holes on kit frame to
snap parts together and secure (Figure 1).
2. Push clips on into slots on rear of kit frame support tray
to secure (Figure 1).
3. Cut off tabs on both mounting brackets labeled “A” “B”or
that are shown as shaded (Figure 2). The tabs should be “C”
the only remaining tabs.
4. Secure side to kit assembly with mounting brackets
studs nutsand supplied (Figure 1).
5. Choose the proper spacers (supplied with your order) to
allow receiver nosepiece to extend 1/8” to 1/4” beyond
face of trimplate (Figure 3).
6. Insert receiver shafts (with spacers in place) through
openings in trimplate. Secure receiver and faceplate
with shaftnuts supplied with receiver.
7. Attach control knobs.
1/8” -1/4”
â–˛
â–˛
Spacer
Shaft Receiver Assembly
3
FIGURE 3
Shaftnuts
®
Copyright 2003 Crutchfield Corporation
FIGURE 1
Trimplate
Kit Frame
Support Tray
Mounting Bracket
Mounting Bracket
Faceplate
Control Knobs
Stud
Nut
Chevrolet/GMC
Tools Required
â–˛
3/8” Socket
Deep Socket
(size depends upon receiver)
FIGURE 2
Cut off A & B
(shaded tabs)
on both brackets
These “C” tabs must remain
Hacksaw


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 90-3044P

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 90-3044P benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-