Metra 70-5008 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Metra 70-5008 (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
Orange - Illumination
Yellow - 12 Volts Constant Power
Red - 12 Volts Switched Power
Black - Chassis Ground
Orange/White - Not Used (tape Off)
Orange/Black - Not Used (tape off)
Blue - Power Antenna
Blue/White - Not Used (tape off)
Receiver Wiring Adaptor
120 70-5008
Revision 02/15/18
STEP 1 -- MATCH & CONNECT WIRES
*120705008*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
Copyright 2018 Crutchfield Corporation
Match wires below to the matching function of each wire on
your receiver (refer to instructions supplied with receiver).
The wire colors of your new receiver may, or may not,
match the wire colors of the adaptor. Match adaptor and
receiver wires by function, disregarding color.
Your receiver illumination wire could be Orange or
Orange/White. As with other wires, match this wire to the
illumination wire in this harness by function, not by color.
If your receiver does not have an illumination wire, tape off
the illumination wire.
Individually tape off any unused wires.
Route harnesses, bypass amplifier and make final wiring
connections following instructions on pages 2 & 3.
A.
B.
C.
D.
White - Left Front Speaker Positive
Blue - Power Antenna
Violet - Right Rear Speaker Positive
Green - Left Rear Speaker Positive
Gray - Right Front Speaker Positive
Gray/Black - Right Front Speaker Negative
White/Black - Left Front Speaker Negative
Violet/Black - Right Rear Speaker Negative
Green/Black - Left Rear Speaker Negative
This wire is only used in 1995-'97 Ford Explorers and
Mercury Mountaineers that are factory-equipped
with the JBL system. It connects to the power
antenna lead on the new receiver. All other vehicles
use the Blue Wire on the Power harness.
Speaker Harness
(actual length of wires is much longer than shown)
Power Harness
STEP 2 -- HARNESS ROUTING
Receiver Adaptor/Amplifier Bypass
A. Run the speaker harness wires
from the receiver to the factory
amplifier location. (Refer to the
Crutchfield MasterSheet for
your particular vehicle to locate
and access the amplifier).
B. Disconnect both factory
harnesses from the amplifier.
C. Plug the speaker harness into
the factory harness disconnected
from the amplifier output.
D. Tape off and secure the unused
harness.
120 70-5008
Factory Amplifier
Factory Harness
120 70-5008
Speaker Harness
Receiver Rear
120 70-5008
Power Harness
Factory Harness
Copyright 2018 Crutchfield Corporation
Page 2
Antenna Lead
Continued on the next page.
120 70-5008
Page 3
STEP 3 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
Copyright 2018 Crutchfield Corporation
STEP 4 -- APPLICATION
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 3 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration
Receiver Wiring Adaptor Connections
A. When ready to install the
receiver, plug the wiring
Adaptor from the new receiver,
or receiver assembly into the
factory radio harness(es) in the
vehicle dash.


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 70-5008

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 70-5008 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-