Metabo N5021A Bedienungsanleitung
Metabo
Broschüren
N5021A
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metabo N5021A (61 Seiten) in der Kategorie Broschüren. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/61
Model Stapler
Modèle Agrafeuse
Modelo Grapadora
Instruction and safety manual
Manuel d’instructions et de sécurité
Instrucciones y manual de seguridad
N 5024A2 • N 5021A
DANGER
Improper use of this Stapler can result in death or serious injury!
This Manual contains important information about product safety.
Read and understand this Manual before operating the Stapler.
Never allow anyone who has not reviewed this manual to use the tool.
This manual should be stored in safe place.
DANGER
Une utilisation incorrecte et sans respecter la sécurité de cette agrafeuse risque d’entraîner
la mort ou des blessures graves !
Ce manuel renferme des instructions importantes sur la sécurité de l’outil.
Lire et bien assimiler ce manuel avant d’utiliser l’agrafeuse.
Cet outil ne doit jamais être utilisé par une personne n’ayant pas pris connaissance du manuel.
Ce mode d’emploi doit être conservé dans un endroit sûr.
PELIGRO
¡La utilización inadecuada e insegura de esta grapadora puede resultar en lesiones serias
o en la muerte!
Este manual contiene información importante sobre la seguridad del producto.
Lea y entienda este manual antes de utilizar la grapadora.
La herramienta no deberá utilizarse sin haber leído previamente este manual.
Este manual debe ser guardado en un lugar seguro.
ATTENTION : USERS OF metabo HPT NAILERS
(Read this information carefully for your satisfaction and safety)
This metabo HPT nailer has a STANDARD CONTACT TRIP MECHANISM (Bounce Fire). An OPTIONAL
SEQUENTIAL TRIP MECHANISM kit (SINGLE SHOT) is available as shown below.
Models Order part number
NR83A, NR83AA, NV83A, NV65AC, VH-650, NT65A2, NV50AA, NV50A1, NV50AP,
NR83AA2, N5008AC, NV50AP2, NV83A2, N5024A, N5010A, N5021A, N5008AC2, N5024A2
876762
NV45AB, NV45AB2, NV45AE 878226
NR90AC, NV65AH, NR90AA, NV45AC, NR90AC2 881973
NT65AA, NT65MA 880414
NV75AG 883991
To order in U.S. call toll free 1-800-706-7337. In Canada call toll free 1-800-970-2299.
THE STANDARD CONTACT TRIP MECHANISM (Bounce Fire) is for use where rapid fastener placement is desired
and must be operated in accordance with the following “Methods of Operation”.
This metabo HPT nailer is equipped with a push lever and does not operate unless the push lever is depressed
(upward position). There are two methods of operation to drive nails with this Nailer.
1. Intermittent operation (Trigger Fire)
2. Continuous operation (Push Lever Fire)
(1) Intermittent operation (Trigger Fire)
1
Position the nail outlet on the workpiece with fi nger off the trigger.
2
Depress the push lever fi rmly until it is completely depressed.
3
Pull the trigger to drive a nail.
4
Remove fi nger from the trigger.
To drive another nail, move the nailer along the workpiece and repeat this procedure.
(2) Continuous operation (Push Lever Fire)
1
Pull the trigger with the push lever pointing towards but not touching the workpiece.
2
Depress the push lever against the workpiece to drive a nail.
3
Move the nailer along the workpiece with a bouncing motion. Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been driven, remove fi nger from the trigger.
WAR NING
: Keep your fi nger off the trigger except during fastening operation, because serious
injury could result if the push lever accidentally contacts you or others in work area.
WAR NING
: Keep hands and body away from the discharge area. The nailer with contact trip
mechanism may bounce from the recoil of driving a fastener and unwanted subsequent
fastener may be driven, possibly causing injury.
THE OPTIONAL SEQUENTIAL TRIP MECHANISM (SINGLE SHOT PARTS) is for use where precision fastener
placement is desired and must be operated in accordance with the following “Method of Operation”.
You must fi rst depress the push lever (upward position) where you want to drive a nail and then pull
the trigger. After the each nail is driven, completely release the trigger and lift the tool off the work surface. An
OPTIONAL SEQUENTIAL TRIP MECHANISM may reduce the possibility of bodily injury to you or others in the
work area. This is because it is less likely to drive an unwanted nail if you keep the trigger pulled and accidentally
bump the push lever against yourself or others. An OPTIONAL SEQUENTIAL TRIP MECHANISM may also reduce
the speed of operation compared to the standard contact trip mechanism.
NOTE : Both STANDARD CONTACT TRIP MECHANISM and OPTIONAL SEQUENTIAL TRIP MECHANISM are safe if
used as described above and according to all warnings and instructions.
2
English
IMPORTANT SAFETY INFORMATION
Read and understand tool labels and all of the operating instructions, safety precautions and warnings
in this manual before operating or maintaining this Stapler.
Failure to follow warnings could result in DEATH or SERIOUS INJURY.
Most accidents that result from the operation and maintenance of Staplers are caused by the failure to observe basic
safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it
occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Manual and in the sections which contain the
operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identifi ed by DANGERS and WARNINGS
on the Stapler and in this Manual.
NEVER use this Stapler for applications other than those specifi ed in this Manual.
DEFINITIONS OF SIGNAL WORDS
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or
may cause machine damage.
NOTE emphasizes essential information.
EXPLANATION OF THE STAPLING ACTION OF THE metabo HPT STAPLER
○
CONTACT ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull the trigger to drive the fastener.
First, pull the trigger; next, press the push lever against the wood to drive the fastener.
If the Trigger is held back, a fastener will be driven each time the Push Lever is pressed against the wood.
3
English
Produktspezifikationen
| Marke: | Metabo |
| Kategorie: | Broschüren |
| Modell: | N5021A |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Metabo N5021A benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Broschüren Metabo
28 Mai 2024
28 April 2024
25 April 2024
21 April 2024
21 April 2024
10 April 2024
22 März 2024
1 März 2024
24 Januar 2024
5 Dezember 2023
Bedienungsanleitung Broschüren
- Broschüren Targus
- Broschüren Makita
- Broschüren Bosch
- Broschüren Parkside
- Broschüren Whirlpool
- Broschüren Rapid
- Broschüren DeWalt
- Broschüren Einhell
- Broschüren Hikoki
- Broschüren Hitachi
- Broschüren Güde
- Broschüren Sencor
- Broschüren Rexel
- Broschüren Globaltronics
- Broschüren Dedra
- Broschüren Silverline
- Broschüren President
- Broschüren Milwaukee
- Broschüren Sun Joe
- Broschüren Aqua Joe
- Broschüren Porter-Cable
- Broschüren Swingline
- Broschüren POWERNAIL
Neueste Bedienungsanleitung für -Kategorien-
25 Juni 2024
17 Juni 2024
7 Juni 2024
7 Juni 2024
6 Juni 2024
6 Juni 2024
6 Juni 2024
6 Juni 2024
6 Juni 2024
6 Juni 2024