Meliconi Speedy 2.1 Bedienungsanleitung

Meliconi Fernbedienung Speedy 2.1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Meliconi Speedy 2.1 (4 Seiten) in der Kategorie Fernbedienung. Dieser Bedienungsanleitung war für 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
Speedy 2.1
Thank you for choosing a Meliconi remote control.
The Speedy 2.1 remote control is designed to command and a DECODER (satellite or digital terrestriala TV ).
IMPORTANT! When the remote control is set to control only device (example: TV), all the buttons will control that one
device; whilst when it is set to control 2 devices (TV + DECODER), e buttons will control the TV, only th V+ V-
whilst the other buttons will control the DECODER.
Speedy 2.1 is a simplied remote control; it provides ONLY the functions on the keypad.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio
frequency (e.g. voice commands and pointers) are not supported.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The remote control requires 2 new 1.5V alkaline batteries, not included in the AAA/LR03
package. Insert with the correct polarity as shown in gure.
DO NOT use batteries. rechargeable
BATTERIES TEST: Press and hold the 5 button and check that the LED remains on
continuously until the button is released. If the light is o or blinks, the inserted batteries are low,
therefore they need replacement.
WARNING:
As the remote control is capable of controlling 2 devices, during setup you must select the operation mode then dene which ;
device you want to control. (TV / STB)
To select the operation mode, press the button quickly and repeatedly until the LED corresponding to
the device you want to operate is switched on. ( led / led) TV = red STB = green
Before using the remote control, for each device you wish to control, it is to set a it matched. essential specic code,
Identify the specic code and set it into the remote control using one of the following ways:
MANUAL
SEARCH
SMARTPHONE
TABLET - WEB
ACTIVATION OF REMOTE CONTROL
SELECTION OF OPERATING MODE
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
INSERTING THE BATTERIES
SAFETY WARNINGS
The remote control and batteries should not be exposed to excessive heat such as sunlight, re
or the like.
The product . Keep out of reach of children or domestic animals. is not a toy
Use the -code on the side or connect to the page and follow the instructions. qr www.cme.it
Once you have found the specic code for your device, set it in the remote control as described in the
ENTERING THE CODE DIRECTLY chapter.
ATTENTION : searching for the suitable code could last up to 5 minutes.
• Stand in front of the device to be controlled and make sure it is ON (not in stand-by). If necessary, switch
it on using the original remote control (if this is still working) or the buttons present on the device itself. (on
TVs they can be on the side or the top)
• On the MELICONI remote control and then press and hold the butt until select the operating mode on
the LED of the remote control lights up; lease. re
• Pointing the remote control towards the device, PRESS AND HOLD butt and wait the ON/OFF on
(even up to 5 minutes) for the device to switch o.
• , w the device turn o IMMEDIATELY RELEASE the button. PAY ATTENTION hen ,
• Three nal ashes indicate that the operation has been completed successfully.
(only to be performed if you know the to be set) specic code
• On the MELICONI remote control and then press and hold the button until select the operating mode
the LED lights up; release.
• Immediately enter the previously identied specic code.
• Three nal ashes indicate that the operation has been completed successfully.
If necessary it is possible to reset the remote control and bring it back to the initial conditions. completely
WARNING : All user settings will be lost. Operate as follows:
• On the MELICONI remote control press and hold the button until the LED lights up; release.
• Enter the code . 0100
• Three nal ashes indicate that the operation has been completed successfully.
RESET THE REMOTE CONTROL
If the remote control does NOT carry out the three nal ashes, the setting is NOT successful; repeat the procedure.
If still unsuccessful, it means that the code is not included in the remote control, contact the ASSISTANCE.
ENTERING THE CODE DIRECTLY
VERIFY
Check that the MELICONI remote control operates your device the main functions if it does not, the in ; REPEAT
procedure.
NOTE: When the list of codes to be searched is over, the remote control exits the search and the LED remains o.
If no results are obtained, try using the procedure described in the SMARTPHONE - TABLET - WEB chapter or contact
the ASSISTANCE.
MANUAL SEARCH
SMARTPHONE - TABLET - WEB
For any future activation of the remote control, it is advisable to extract and note the code in use, operate as follows:
• On the MELICONI remote control and then press and hold the select the operating mode
button until the LED lights up; release.
• Enter the code . 0010
• After a pause of several seconds, the LED produces four sets of ashes, spaced out,
corresponding to the code to be obtained. Count the number of ashes. Each set of ashes
corresponds to one digit in the code. Ten ashes correspond to the digit zero “ ”0 .
( code obtained = example 1701)
• Make a note of the code obtained. You may need it in future.
If you want to delete the function in combination with a single button, operate as follows:
• On the MELICONI remote control and then press and hold the button. select the operating mode
• When the LED turn on, without releasing the button 1 , enter the code 600; release the buttons.
• Within 30 seconds, press and hold the button of which you want to delete the function; wait three ashes indicating the end
of the operation, release the button. (to recall the original function, setting again the activation code)
● THE REMOTE CONTROL IS NEW AND YOU CAN NOT MAKE IT WORK IF
It is possible that the code set in the remote control is incorrect for the device that you want to control Check that you have .
carried out all the settings procedures correctly. If necessary repeat them, following all the steps indicated carefully.
Consult the website to identify the specic code associated with your device or contact the ASSISTANCE. www.cme.it
● IF THE REMOTE CONTROL IS NO LONGER ABLE TO CONTROL THE DEVICE
Disconnect the device from the electric socket and leave it without power for a few minutes; switch the device on again.
Remove the batteries from the remote control, press the butto twice and insert NEW batteries. ON/OFF n
Make sure that the remote control is pointing at the device without any obstacles between them.
If necessary try to the RESET OF THE REMOTE CONTROL and carry out a new activation.
● SOME FUNCTIONS ARE NOT AVAILABLE ON THE REMOTE CONTROL IF
Usually the MELICONI remote control makes available only the present functions on his keyboard provided they are ,
available also on the original remote control.
If some of the MAIN functions are not available, you are probably using an incorrect code. Find and set a more suitable code
as described in the ACTIVATION OF REMOTE CONTROL chapter.
● HOW TO CHECK IF THE REMOTE CONTROL SENDS INFRARED SIGNALS
The human eye is not able to detect infrared signals use a camera (even that of the mobile phone). ;
Aim the infrared LED located in front of the remote control (not the red LED above and press and hold on the remote control )
the button. 5
If you see through the camera, the LED light with short white / light blue ashes means that the remote control works and
emits infrared.
ATTENTION!
Most problems are caused by using insuciently charged batteries.
We recommend checking and replace them as shown in the INSERTING THE BATTERIES chapter.
TROUBLESHOOTING (F.A.Q.)
DELETE FUNCTION BY SINGLE BUTTON
DISPLAY CODE IN USE

Produktspezifikationen

Marke: Meliconi
Kategorie: Fernbedienung
Modell: Speedy 2.1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Meliconi Speedy 2.1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Fernbedienung Meliconi

Meliconi

Meliconi universal 4 Bedienungsanleitung

23 September 2024
Meliconi

Meliconi gumbody light facile Bedienungsanleitung

23 September 2024
Meliconi

Meliconi Pratico 2 Bedienungsanleitung

18 September 2024
Meliconi

Meliconi Personal 2 plus Bedienungsanleitung

29 August 2024
Meliconi

Meliconi Speedy 2.1 Bedienungsanleitung

21 August 2024
Meliconi

Meliconi GumBody Light Bedienungsanleitung

21 August 2024
Meliconi

Meliconi Gumbody Personal 7 plus Bedienungsanleitung

20 August 2024
Meliconi

Meliconi Gumbody Personal 2 Bedienungsanleitung

20 August 2024
Meliconi

Meliconi Control TV+ Bedienungsanleitung

20 August 2024
Meliconi

Meliconi Gumbody Personal 6 plus Bedienungsanleitung

20 August 2024

Bedienungsanleitung Fernbedienung

Neueste Bedienungsanleitung für -Kategorien-

Neewer

Neewer RT112 Bedienungsanleitung

8 Oktober 2024
Neewer

Neewer RT113 Bedienungsanleitung

8 Oktober 2024
Logitech

Logitech Harmony 600 Bedienungsanleitung

5 Oktober 2024
Furman

Furman RS-2 Bedienungsanleitung

5 Oktober 2024
Hannspree

Hannspree YES-001016 Bedienungsanleitung

3 Oktober 2024
Canon

Canon RS-80N3 Bedienungsanleitung

3 Oktober 2024
Alpine

Alpine RUE-M300 Bedienungsanleitung

2 Oktober 2024
Energy Sistem

Energy Sistem 4100 Bedienungsanleitung

23 September 2024
Humax

Humax RS505 Bedienungsanleitung

23 September 2024
Unitron

Unitron Remote Control Bedienungsanleitung

22 September 2024