Maxsa 43319-X Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Maxsa 43319-X (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
ASSEMBLY AND INSTRUCTION GUIDE
ABOUT YOUR LED OUTDOOR WALL SCONCE
The
LED Outdoor Wall Sconce
is perfect for porches,
doorways, or around the house.
The
LED Outdoor Wall Sconce
has a built-in motion sensor,
which automatically turns on the light when movement of a
heat source (such as people, animals, or cars) is detected in
the area. The light remains on while motion continues to be
detected in the area.
The
LED Outdoor Wall Sconce
also has a built-in photosensor
so that the light only turns on at night.
The
LED Outdoor Wall Sconce
may function irregularly or not
at all at temperatures below Ëš F / Ëš C. 0 -17.8
Normal operation will return when the temperature rises.
The
LED Outdoor Wall Sconce
requires 4 C cell batteries (not
included). The batteries typically last up to 1 year under
normal use.
The 5 super bright LEDs in the
LED Outdoor Wall Sconce
have an estimated life of 30,000 hours so they should never
need changing.
BATTERY INSTALLATION
1. The
LED Outdoor Wall Sconce
requires 4 C cell batteries
(not included).
2. To access the battery compartment, remove the 2 thumb
screws from the top cover. Remove the top cover.
BATTERY INSTALLATION (CONTINUED)
3. Remove the battery compartment cover by squeezing
the two tabs on the cover inward and pulling up.
4. Install the 4 C cell batteries in the proper +/- polarity
orientation as shown in the illustration above. The
positive ends of the batteries should face the low battery
contacts and the negative ends of the batteries should
face the elevated spring terminals in the battery
compartment. If your unit includes a clear rubber spacer
between the two halves of the battery compartment,
please reinsert it between the two halves.
5. Reinstall the battery compartment cover by aligning the
tabs and pressing the battery compartment cover down
until the battery compartment cover clicks into place.
6. Reassemble the
LED Outdoor Wall Sconce
by replacing
the top cover and re-installing the two thumb screws.
Tighten the thumb screws by hand as tightly as possible
to ensure a waterproof seal.
Model # 4 9
page 1
LED Outdoor Wall Sconce
BATTERY-POWERED MOTION-ACTIVATED
Thumb Screw
Battery Compartment Cover
4 C Batteries
Squeeze tabs inward
Insert 4 C batteries
in the proper +/-
orientation
page 2
Note: If your
LED Outdoor Wall Sconce
does not turn on after
battery installation:
• Make sure the batteries have been inserted matching the
correct + / - polarity orientation and are making secure
contact with the terminals.
• Make sure you are testing the
LED Outdoor Wall Sconce
in
a dark area since the light will only turn on at night.
Note: Dispose of old batteries properly, following your local and
state regulations. Do not dispose of batteries in regular
household refuse or into a fire.
The selected location should not be near light sources such as
street or porch lighting as these may cause the
LED Outdoor Wall
Sconce LED Outdoor Wall Sconce to turn off automatically. The
should also be installed away from heaters, air conditioners,
barbecues, vents, and large reflective surfaces such as swim-
ming pools and jacuzzis, and white walls.
You should also install the
LED Outdoor Wall Sconce
at least 30
feet away from the street since passing cars might activate the
light.
Ideally, the
LED Outdoor Wall Sconce
should be mounted with
the detector at the height of or above the objects to be detected.
The motion sensor has a detection area of about 22 feet (7
meters) within a 100 degree angle of the sensor. The sensor is
more sensitive to movement across the detection area than
movement directly towards or away from the sensor.
At night, the LED lights will remain on for approximately 30
seconds after the last detected movement. If a movement is
detected while the lights are on, the light duration will be reset
and remain on for an additional 30 seconds (approximately).
The included mounting bracket and screws can be used to
mount the securely to a wall.LED Outdoor Wall Sconce
To install the mounting bracket:
1. Remove the mounting bracket from the back of the base by
unscrewing the two thumb screws on the front of the base.
2. Align the mounting bracket on the wall and mark the
locations of the two holes to be drilled with a pencil.
Remove the mounting bracket from the wall.
3. Drill pilot holes for screws. Screw anchors should be used
for cement, brick, or similar surfaces.
4. Align the mounting bracket on the wall and install the two
screws using a screwdriver.
1. Align the
LED Outdoor Wall Sconce on the mounting
bracket so that the two bolts go through the two holes on
the front of the base.
2. Reinstall the two thumb screws on the front of the base and
tighten securely.
Your is LED Outdoor Wall Sconce
equipped with an energy-saving
switch, located on the right side of
the sconce. The switch controls
the power output for the sconce.
Choose 100% Brightness setting
for full brightness, or 50%
Brightness setting to conserve
battery power.
BATTERY INSTALLATION (CONTINUED)
CHOOSING A LOCATION
INSTALLING THE MOUNTING BRACKET
MOUNTING THE LIGHT
USING THE ENERGY SAVING SWITCH
30 feet or more from street
90
Degrees
22
feet
Direction of
Movement
CHOOSING A LOCATION, CONTINUED
TROUBLESHOOTING
MAXSA Innovations
8412 Cathedral Forest Drive
Fairfax Station, VA 22039
Tel: 703-495-0661
www.maxsainnovations.com
v
©20 MAXSA Innovations, LLC
MADE IN CHINA
Light does not turn on
when there is movement
in the detecton area.
Light turns on for no
apparent reason (false
trigger).
Light turns on during
daylight hours.
1. Batteries are old.
2. Nearby lighting is too bright.
3. The light is facing the wrong direction.
1. Heat sources such as air conditioners,
vents, barbecues, other outside lighting, or
moving cars are false triggering the
motion sensor.
2. Pets or other animals are false triggering
the motion sensor.
3. Reflections from swimming pools,
jacuzzis, white walls, or other large
reflective surfaces are false triggering the
motion sensor.
1. A roof, wall, tree, or other object is casting
a shadow on the sensor.
1. Replace the batteries.
2. Install the
LED Outdoor Wall Sconce
in a
different location or facing a different
direction, away from other lighting.
3. Install the
LED Outdoor Wall Sconce
facing the desired detection area.
1. Install the
LED Outdoor Wall Sconce
away
from the sources of interference.
2. Mounting the
LED Outdoor Wall Sconce
higher or facing the light in a different
direction may help.
3. Install the
LED Outdoor Wall Sconce
away
from the sources of reflections.
1. Install the
LED Outdoor Wall Sconce
in a
non-shaded location or facing a direction
away from sources of shadows.
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
SPECIFICATIONS
Batteries Required: 4 C cell alkaline, Ni-MH, or Ni-Cd
LEDs: 5 x 0.075 Watt LEDs
Voltage: 6V DC
Light Duration: approximately 30 seconds
Detection Angle: 90Ëš (cone)
Maximum Detection Distance: 22 feet (7 meters)
Housing Weatherproof Rating: IP33
Circuitry Weatherproof Rating: IP44
page 3


Produktspezifikationen

Marke: Maxsa
Kategorie: Nicht kategorisiert
Modell: 43319-X

Brauchst du Hilfe?

Wenn Sie Hilfe mit Maxsa 43319-X benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Maxsa

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-