Match UP 7DSP Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Match UP 7DSP (17 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/17
UP 7DSP
U P G R A D E
7-Kanal Upgrade-Verstärker mit integriertem 8-Kanal
64 Bit DSP für universelle Anwendungen
7-channel upgrade ampliî‚¿er with integrated 8-channel
64 Bit DSP for universal applications
deutsch / english
17
Dear Customer,
Congratulations on your purchase of this innovative
and high-qual ity MATCH product.
Thanks to more than 30 years of experience in
research and development of audio products this
ampliî‚¿er sets new standards in the range of digital
ampliî‚¿ers.
We wish you many hours of enjoyment with your
new MATCH UP 7DSP.
Yours,
AUDIOTEC FISCHER
General installation instructions for MATCH
components
To prevent damage to the unit and possible injury,
read this manual carefully and follow all installation
instructions. This product has been checked for
proper function prior to shipping and is guaranteed
against manufacturing defects.
Before starting your installation, disconnect the
battery’s negative terminal to prevent damage
totheunit,reand/orriskofinjury.For a proper
performance and to ensure full warranty coverage,
we strongly recommend to get this product installed
by an authorized MATCH dealer.
Install your UP 7DSP in a dry location with sufî‚¿cient
air circulation for proper cooling of the equipment.
For safety reasons, the UP 7DSP must be profes-
sionally installed. Therefore, use the two mounting
plates which are included in delivery. These are at-
tached to the bottom of the ampliî‚¿er with two short
screws which are included in delivery, too.
When screwing the ampliî‚¿er to the vehicle chassis,
carefully examine the area around and behind the
proposed installation location to ensure that there
are no electrical cables or components, hydraulic
brake lines or any part of the fuel tank located be-
hind the mounting surface. Failure to do so may re-
sult in unpredictable damage to these components
and possible costly repairs to the vehicle.
General instruction for connecting the UP 7DSP
ampliî‚¿er
The UP 7DSP ampliî‚¿er may only be installed in mo-
tor vehicles which have a 12 Volts negative terminal
connected to the chassis ground. Any other system
could cause damage to the ampliî‚¿er and the electri-
cal system of the vehicle.
The positive cable from the battery for the entire
sound system should be provided with a main fuse
at a distance of max. 30 cm from the battery. The
value of the fuse is calculated from the maximum
total current draw of the car audio system.
Use only the included MATCH cable or
the optional PP-ISO cable for connec-
tion of the UP 7DSP. The use of other
cables can result in damage of the ampli-
er, the headunit/carradio ortheconnected
loudspeakers! The fuses of the amplier may
only be replaced by identically rated fuses
(2x25A)toavoiddamageoftheamplier.
Prior to installation, plan the wire routing to avoid
any possible damage to the wire harness. All
cabling should be protected against possible
crushing or pinching hazards. Also avoid routing
cables close to potential noise sources such as
electric motors, high power accessories and other
vehicle harnesses.
Congratulations!
General instructions
18
Connectors and control units
1 Auto Remote
This switch allows to activate / deactivate the
automatic turn-on feature of the ampliî‚¿er
.
2 System Connector 2
Connector for loudspeakers and / or sub-
woofers.
3 Clipping LED
This LED lights up red if one of the analog
inputs is overdriven.
4 System Connector 1
Connector for the UP 7DSP cable harness.
Only use the supplied connection cable to
connect the ampliî‚¿er to the car radio.
5 Fuse LED
This LED will light up if the fuses inside the
ampliî‚¿er are blown.
6 +12 V
Connector for the +12 V power cable to the
positive terminal of the battery.
7 GND
Connector for the ground cable (negative
terminal of the battery or metal body of the
vehicle).
8 REM
Connector for the remote cable.
1 2 3 4 5 6 7 8
9 USB Input
Connects the UP 7DSP to your PC.
10 Control pushbutton
Use this button to either switch between the
setups or initiate a reset of the device.
11 Status LED
This LED indicates the operating mode of
the ampliî‚¿er and the setup that has been
chosen.
12 Control Input
Multifunction interface for e.g. an optional
remote control or other MATCH UP 7DSP
accessory.
13 Optical Input
Optical input for digital stereo signals (SPDIF
format).
14 Gain
Control for adjusting the input sensitivity.
15 Remote Out
The remote output has to be used to turn on /
off external ampliî‚¿ers that are connected to
the .Line Out
16 Line Out
Mono line output for connecting external am-
pliî‚¿ers. Make sure that the remote output is
used to turn on these devices.
10 119 16151312 14


Produktspezifikationen

Marke: Match
Kategorie: Nicht kategorisiert
Modell: UP 7DSP

Brauchst du Hilfe?

Wenn Sie Hilfe mit Match UP 7DSP benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Match

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-