Makita TW007GZ Bedienungsanleitung

Makita Nicht kategorisiert TW007GZ

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Makita TW007GZ (16 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/16

INSTRUCTION MANUAL

Cordless Impact Wrench

TW007G

TW008G

ENGLISH: Original instructions

Read before use.

2 ENGLISH

SPECIFICATIONS

Model: TW007G TW008G

Fastening capacities Standard bolt M10 - M24

High tensile bolt M10 - M16

Square drive 12.7 mm

No load speed Max impact mode (4) 0 - 2,300 min

-1

Hard impact mode (3) 0 - 1,900 min

-1

Medium impact mode (2) 0 - 1,200 min

-1

Soft impact mode (1) 0 - 600 min

-1

Impacts per minute Max impact mode (4) 0 - 2,900 min

-1

Hard impact mode (3) 0 - 2,700 min

-1

Medium impact mode (2) 0 - 1,900 min

-1

Soft impact mode (1) 0 - 1,200 min

-1

Overall length (with battery cartridge BL4040) 170 mm

Rated voltage D.C. 36 V - 40 V max

Net weight 2.7 - 3.3 kg

•

Due to our continuing program of research and development, the specications herein are subject to change without notice.

• Specications may dier from country to country.

• The weight may dier depending on the attachment(s), including the battery cartridge. The lightest and heavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL4020* / BL4025* / BL4040* / BL4050F

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Read instruction manual.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household waste!

In accordance with the European Directive

on waste electrical and electronic equipment

and on accumulators and batteries and

waste accumulators and batteries, as well as

their adaptation to national law, waste elec-

trical equipment, batteries and accumulators

should be stored separately and delivered

to a separate collection point for municipal

waste, operating in accordance with the

regulations on environmental protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

Intended use

The tool is intended for fastening bolts and nuts.

Noise

The typical A-weighted noise level determined accord-

ing to EN62841-2-2:

Model TW007G

Sound pressure level (L

pA) : 97 dB(A)

Sound power level (L

WA) : 108 dB (A)

Uncertainty (K) : 3 dB(A)

Model TW008G

Sound pressure level (L

pA) : 97 dB(A)

Sound power level (L

WA) : 108 dB (A)

Uncertainty (K) : 3 dB(A)

NOTE: The declared noise emission value(s) has

been measured in accordance with a standard test

method and may be used for comparing one tool with

another.

NOTE: The declared noise emission value(s)

may also be used in a preliminary assessment of

exposure.

3 ENGLISH

WARNING: Wear ear protection.

WARNING:

The noise emission during actual

use of the power tool can dier from the declared val-

ue(s) depending on the ways in which the tool is used

especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such

as the times when the tool is switched o and when

it is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN62841-2-2:

Model TW007G

Work mode: impact tightening of fasteners of the maxi-

mum capacity of the tool

Vibration emission (a

h) : 19.7 m/s2

Uncertainty (K) : 1.5 m/s

Model TW008G

Work mode: impact tightening of fasteners of the maxi-

mum capacity of the tool

Vibration emission (a

h) : 19.7 m/s2

Uncertainty (K) : 1.5 m/s

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING:

The vibration emission during actual

use of the power tool can dier from the declared val-

ue(s) depending on the ways in which the tool is used

especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such

as the times when the tool is switched o and when

it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodied plugs and matching outlets will

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

Power tools can produce electromagnetic elds

(EMF) that are not harmful to the user. However,

users of pacemakers and other similar medical

devices should contact the maker of their device and/

or doctor for advice before operating this power tool.

Personal safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication. A moment of inattention while operating

power tools may result in serious personal injury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

3. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your nger on the switch or energising power tools

that have the switch on invites accidents.

4 ENGLISH

4. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

5. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

9. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

2. Do not use the power tool if the switch does

not turn it on and o. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any adjust-

ments, changing accessories, or storing power

tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

Maintain power tools and accessories. Check for

misalignment or binding of moving parts, break-

age of parts and any other condition that may

aect the power tool’s operation. If damaged, have

the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

When using the tool, do not wear cloth work gloves

which may be entangled. The entanglement of cloth work

gloves in the moving parts may result in personal injury.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a re.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied. Damaged or modied batteries

may exhibit unpredictable behaviour resulting in

re, explosion or risk of injury.

6. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or tem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outside the specied range may damage the

battery and increase the risk of re.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

2. Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

3. Follow instruction for lubricating and chang-

ing accessories.

5 ENGLISH

Cordless impact wrench safety

warnings

1. Hold the power tool by insulated gripping

surfaces, when performing an operation

where the fastener may contact hidden wiring.

Fasteners contacting a "live" wire may make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

2. Wear ear protectors.

3. Check the impact socket carefully for wear,

cracks or damage before installation.

4. Hold the tool rmly.

5. Keep hands away from rotating parts.

6. Do not touch the impact socket, bolt, nut or the

workpiece immediately after operation. They

may be extremely hot and could burn your skin.

7. Always be sure you have a rm footing.

Be sure no one is below when using the tool in

high locations.

8. The proper fastening torque may dier

depending upon the kind or size of the bolt.

Check the torque with a torque wrench.

9. Make sure there are no electrical cables, water

pipes, gas pipes etc. that could cause a hazard

if damaged by use of the tool.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product.

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper the battery

cartridge. It may result in a re, excessive heat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask o open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may result in poor performance or

breakdown of the tool or battery cartridge.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines. It may result in a malfunction

or breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

6 ENGLISH

Tips for maintaining maximum

battery life

Charge the battery cartridge before completely dis-

charged. Always stop tool operation and charge the

battery cartridge when you notice less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridge rmly may cause them to slip o your hands

and result in damage to the tool and battery cartridge

and a personal injury.

► 1. 2. 3. Red indicator Button Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator as

shown in the gure, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts o power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the tool/battery is operated in a manner that

causes it to draw an abnormally high current, the tool

stops automatically. In this situation, turn the tool o

and stop the application that caused the tool to become

overloaded. Then turn the tool on to restart.

Overheat protection

When the tool/battery is overheated, the tool stops

automatically and the lamp will blink. In this situation, let

the tool cool down before turning the tool on again.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

► 1. 2. Indicator lamps Check button

7 ENGLISH

Indicator lamps Remaining

capacity

Lighted BlinkingO

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may dier slightly

from the actual capacity.

NOTE: The rst (far left) indicator lamp will blink when

the battery protection system works.

Switch action

► 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

To start the tool, simply pull the switch trigger. Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

NOTE: The tool automatically stops when you keep

pulling the switch trigger for 6 minutes.

NOTE: When full speed mode is turned on, the rota-

tion speed becomes fastest even if you do not pull the

switch trigger fully.

For detail information, refer to the section of full speed

mode.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

► 1. Lamp

► 1. Button

To turn on the lamp status, press the button for

one second. To turn o the lamp status, press the but-

ton for one second again.

With the lamp status ON, pull the switch trigger to turn

on the lamp. To turn o, release it. The lamp goes out

approximately 10 seconds after releasing the switch

trigger.

With the lamp status OFF, the lamp does not turn on

even if pulling the trigger.

NOTE: To conrm the lamp status, pull the trigger.

When the lamp lights up by pulling the switch trigger,

the lamp status is ON. When the lamp does not come

on, the lamp status is OFF.

NOTE: When the tool is overheated, the light ashes

for one minute, and then the LED display goes o. In

this case, cool down the tool before operating again.

NOTE: Use a dry cloth to wipe the dirt o the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE: While pulling the switch trigger, the lamp

status cannot be changed.

NOTE: For approximately 10 seconds after releasing

the switch trigger, the lamp status can be changed.

8 ENGLISH

Reversing switch action

► 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

A side for clockwise rotation or from the B side for coun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

9 ENGLISH

Changing the application mode

Changing the impact force

You can change the impact force in four steps: 4 (max), 3 (hard), 2 (medium), and 1 (soft).

This allows a tightening suitable to the work.

The level of the impact force changes every time you press the button .

You can change the impact force within approximately one minute after releasing the switch trigger.

NOTE: You can extend the time to change the impact force approximately one minute if you press the but-

ton or .

Application mode

(Impact force grade displayed on panel)

Maximum blows Purpose

4 (Max) 2,900 min

-1

(/min) Tightening with the maximum force and speed.

Tightening when the force and the speed are desired.

3 (Hard) 2,700 min

-1

(/min) Tightening with less force and speed than Max mode

(easier to control than Max mode).

Tightening when the force and the speed are desired.

2 (Medium) 1,900 min

-1

(/min) Tightening when a good nishing is needed.

Tightening when you need good control power.

1 (Soft) 1,200 min

-1

(/min) Tightening with less force to avoid screw thread breakage.

Tightening when you need ne adjustment with small

diameter bolts.

: The lamp is on.

NOTE: When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button .

NOTE: All lamps on the switch panel go out when the tool is turned o to save the battery power. The impact force

grade can be checked by pulling the switch trigger to the extent that the tool does not operate.

10 ENGLISH

Changing the application mode

This tool employs several easy-to-use application modes for driving bolts with good control.

The type of the application mode changes every time you press the button .

You can change the application mode within approximately one minute after releasing the switch trigger.

NOTE:

You can extend the time to change the application mode approximately one minute if you press the button or .

Application mode

(Assist type displayed on panel)

Feature Purpose

Bolt mode Clockwise

This mode helps to repeat screwdriving continuously with

equal torque. This mode also helps to reduce the risk of

breakage of bolts/nuts due to overtightening.

Counterclockwise

This mode helps to prevent a bolt from falling o. When loosening a

bolt with the tool driving in counterclockwise rotation, the tool automat-

ically stops or slows down after the bolt/nut gets enough loosened.

NOTE:

The timing to stop the driving varies depending on the

type of the bolt/nut and material to be driven. Make a

test driving before using this mode.

Clockwise

Preventing overtightening of

bolts.

Counterclockwise

Loosening bolts.

Bolt mode (1) Clockwise

The tool stops automatically as soon as it has started impact blows.

Counterclockwise

The impact force is 4. The tool stops automatically as soon

as it has stopped impact blows.

–

Bolt mode (2) Clockwise

The tool stops automatically approximately 0.5 second later

from the moment that the tool has started impact blows.

Counterclockwise

The impact force is 4. The tool stops automatically approximately 0.2

second later from the moment that the tool has stopped impact blows.

–

Bolt mode (3) Clockwise

The tool stops automatically approximately 1 second later

from the moment that the tool has started impact blows.

Counterclockwise

The tool slows down the rotation after it has stopped impact blows.

–

: The lamp is on.

NOTE: When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button .

NOTE: All lamps on the switch panel go out when the tool is turned o to save the battery power. The type of the

application mode can be checked by pulling the switch trigger to the extent that the tool does not operate.

11 ENGLISH

Full speed mode

► 1. 2. Button Lamp

When full speed mode is turned on, the tool speed becomes

fastest even if you do not pull the switch trigger fully. When

full speed mode is turned o, the tool speed increases as

you increase the pressure on the switch trigger.

To turn on full speed mode, press and hold the button . To

turn o full speed mode, press and hold the button again.

The lamp turns on while full speed mode is on.

NOTE: Full speed mode continues even after switch-

ing the impact force mode/auto stop mode.

Electronic function

Electric brake

This tool is equipped with an electric brake. If the tool consis-

tently fails to quickly cease to function after the switch trigger

is released, have the tool serviced at a Makita service center.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool.

Selecting correct impact socket

Always use the correct size impact socket for bolts and nuts.

An incorrect size impact socket will result in inaccurate and

inconsistent fastening torque and/or damage to the bolt or nut.

Installing or removing impact socket

Optional accessory

CAUTION: Make sure that the impact socket

and the mounting portion are not damaged before

installing the impact socket.

CAUTION: After inserting the impact socket,

make sure that it is rmly secured. If it comes out,

do not use it.

NOTE: The way of impact socket installation varies

depending on the type of the square drive on the tool.

Tool with the ring spring

Model TW007G

For impact socket without O-ring and pin

► 1. 2. 3. Impact socket Square drive Ring spring

Push the impact socket onto the square drive until it

locks into place.

To remove the impact socket, simply pull it o.

For impact socket with O-ring and pin

► 1. 2. 3. Impact socket O-ring Pin

Move the O-ring out of the groove in the impact socket

and remove the pin from the impact socket. Fit the

impact socket onto the square drive so that the hole in

the impact socket is aligned with the hole in the square

drive.

Insert the pin through the hole in the impact socket and

square drive. Then return the O-ring to the original posi-

tion in the impact socket groove to retain the pin.

To remove the impact socket, follow the installation

procedures in reverse.

13 ENGLISH

OPERATION

CAUTION: Always insert the battery cartridge

all the way until it locks in place. If you can see the

red indicator, it is not locked completely. Insert it fully

until the red indicator cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you

or someone around you.

Hold the tool rmly and place the impact socket over

the bolt or nut. Turn the tool on and fasten for the proper

fastening time.

The proper fastening torque may dier depending upon

the kind or size of the bolt, the material of the workpiece

to be fastened, etc. The relation between fastening

torque and fastening time is shown in the gures.

Proper fastening torque for standard bolt with max

impact mode (4)

(5100)

(4080)

(3060)

(2040)

(1020)

500

400

300

200

100

(kgf•cm)

N•m

1 3

M20

M16

M20

M24

M16

M22

M22 M24

1. 2. Fastening time (second) Fastening torque

Proper fastening torque for high tensile bolt with

max impact mode (4)

(kgf•cm)

N•m

02 31

M12

M14

M16

M12

M14

M16

(3060)

(2040)

(1020)

300

200

100

1. 2. Fastening time (second) Fastening torque

NOTE: Hold the tool pointed straight at the bolt or nut.

NOTE: Excessive fastening torque may damage the

bolt/nut or impact socket. Before starting your job,

always perform a test operation to determine the

proper fastening time for your bolt or nut.

NOTE: If the tool is operated continuously until the

battery cartridge has discharged, allow the tool to rest

for 15 minutes before proceeding with a fresh battery

cartridge.

The fastening torque is aected by a wide variety of

factors including the following. After fastening, always

check the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Impact socket

• Failure to use the correct size impact socket

will cause a reduction in the fastening torque.

• A worn impact socket (wear on the hex end

or square end) will cause a reduction in the

fastening torque.

3. Bolt

• Even though the torque coecient and the

class of bolt are the same, the proper fasten-

ing torque will dier according to the diame-

ter of bolt.

• Even though the diameters of bolts are the

same, the proper fastening torque will dier

according to the torque coecient, the class

of bolt and the bolt length.

4. The use of the universal joint or the extension

bar somewhat reduces the fastening force of the

impact wrench. Compensate by fastening for a

longer period of time.

5. The manner of holding the tool or the material

of driving position to be fastened will aect the

torque.

6. Operating the tool at low speed will cause a reduc-

tion in the fastening torque.

14 ENGLISH

MAINTENANCE

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or attachment

for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Impact socket

• Extension bar

• Universal joint

• Pin 4 Set (For TW008G only)

• Socket extension

• Extension handle

• Makita genuine battery and charger

NOTE: Some items in the list may be included in the

tool package as standard accessories. They may

dier from country to country.

Produktspezifikationen

Marke:	Makita
Kategorie:	Nicht kategorisiert
Modell:	TW007GZ

Brauchst du Hilfe?

Wenn Sie Hilfe mit Makita TW007GZ benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Makita DCG180RTB Bedienungsanleitung

9 Oktober 2024

Makita DEAADP08 Bedienungsanleitung

8 Oktober 2024

Makita VC001GLZ Bedienungsanleitung

2 Oktober 2024

Makita DDG460ZX7 Bedienungsanleitung

2 Oktober 2024

Makita MR002GZ01 Bedienungsanleitung

30 September 2024

Makita 9565CLR Bedienungsanleitung

23 September 2024

Makita HP1621F Bedienungsanleitung

22 September 2024

Makita UC002GD Bedienungsanleitung

21 September 2024

Makita P-21179 Bedienungsanleitung

18 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

BEKO BBVM17400B Bedienungsanleitung

4 Dezember 2024

DeWalt DXV34PTA Bedienungsanleitung

4 Dezember 2024

DeWalt DCF414 Bedienungsanleitung

4 Dezember 2024

DeWalt DXIRFFP25 Bedienungsanleitung

4 Dezember 2024

DeWalt DXIR1A1A2P3 Bedienungsanleitung

4 Dezember 2024

DeWalt DCE450 Bedienungsanleitung

4 Dezember 2024

DeWalt DCMAS5713 Bedienungsanleitung

4 Dezember 2024

DeWalt DCMASBC1 Bedienungsanleitung

4 Dezember 2024

DeWalt DXKH180E Bedienungsanleitung

4 Dezember 2024

DeWalt DWE46150 Bedienungsanleitung

4 Dezember 2024