Majella MVCF-I Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Majella MVCF-I (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
!
!
!
!
!
!
!
!
!
MVCF-I USER MANUAL
Version 1.0
!
!
!
!
!
!
Voltage contolled Filter ( -I) MVCF
User Manual
©2020 Majella Audio
2
INTRODUCTION
The MVCF-I is 12dB/oct voltage controlled
filter, with lowpass and hi-pass mode. The
MVCF-I has voltage controlled resonance
and cutoff. There is control over the input
gain and the resonance can be driven into
self-oscillation.
CONTENT
In the box of the assembled version of the
MVCF-I . contains the following
•!Assembled and Tested Module
•!16 pin to 16 pin ribbon cable
•!Mounting hardware: M3 4x screws
and M3 washers / rack crash
protectors
If anything of the above is missing. Please
contact your dealer or support@majella-
audio.com
SPECIFICATIONS
•!Dimensions: 128.5 x 30 x 45 mm
(6HP)
•!Doepfer A-100 Eurorack compatible
(16 pin power connector)
•!Power consumption: +/- 12V (15mA)
POWER CONNECTION
This module is designed to be connected to
your Eurorack system, using a 16- pin ribbon
cable. The -12V (red stripe) should be
directed as shown in . the picture below
W A RN IN G !
This module is designed for Eurorack
systems. The supply should be +-12V and
connected signals should not be out of the
+-12V range!
Do not reverse polarity when
connecting the power, this will damage
your module permanently!
Voltage contolled Filter ( -I) MVCF
User Manual
©2020 Majella Audio
3
OVERVIEW
OVERVIEW
OVERVIEW
OVERVIEW OVERVIEW (See figu
(See figu
(See figu
(See figu(See figure 1)
re 1)
re 1)
re 1)re 1)
CONTROLS
1.!C U TOF F
Controls the cutoff frequency from 0Hz to
17kHz.
2.!RESONANCE
Controls the resonance amount from 0dB
up to self-oscillation from 95% knob turn.
3.!CUTOFF AMO U N T
Controls the amount of control voltage that
controls the cutoff ( frequency see 9).
4.!RESONANCE AMOU N T
Controls the amount of control voltage that
controls the resonance (see 10).
5.!GAIN
Controls the input signal gain.
6.!HI- PASS button
Normally the MVCF-I is a lowpass VCF.
When this button is pressed the MVCF-I is a
hi-pass VCF.
CONNECTIONS
7.!INPUT
Audio (VCO) input.
8.!OUTPUT
Audio output.
9.!CUTOFF
Control voltage input to control cutoff
frequency.
10.!RESONANCE
Control voltage input to control resonance
amount.
Figure 1: Overview


Produktspezifikationen

Marke: Majella
Kategorie: Nicht kategorisiert
Modell: MVCF-I

Brauchst du Hilfe?

Wenn Sie Hilfe mit Majella MVCF-I benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Majella

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-