Louis Tellier 208030 Bedienungsanleitung

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Louis Tellier 208030 (2 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
208030 en ma 2012.07
*208.030 TRITURATOR - MANUAL
MOULIN N°5
INSTRUCTIONS
ASSEMBLY
1. Set the hopper on the brim of a pan: the support bears
two side hooks provided for this purpose.
2. Place the sieve with the 3 slots facing the 3 studs,
than rotate it slightly, without blocking it.
3. The shaft-handle and cross-piece assembly are then
centred on the sieve spindle and blocked as the right
place with the two holding springs placed on each side
of the hopper.
The two clips of the cross-piece are used to hold the two
springs.
The triturator is ready for use.
DISMANTLING
1. Press on the two holding springs, in order to have the clips
of the cross-piece drop down by themselves. Pull out the
shaft by rotating it clockwise, so as to keep clear of the
stopping blade.
2. Seize the sieve in both hands, by the outer side, and
unfasten with a dead blow anti-clockwise.
NOTE
When the machine is new, the inside of the sieve is rough,
in order to make the L.T. TRITURATOR effective.
On the. contrary, when the inside of the sieve is becoming
smooth, it must be replaced.
M5002
X5002
shaft, handle and cross-piece assembly
M5001
X5001
hopper with holding springs
M5004
X5004
hopper support
M5010-15-20-30-40
X5010-15-20-30-40
sieve
M5003
X5003
holding spring
full-sized sieve perforations
1 mm 1,5 mm 2 mm 3 mm 4 mm
208030 fr ma 2012.07
*208.030 MANUALMOULIN -
MOULIN N°5
INSTRUCTIONS
MONTAGE
1. Disposer le cône sur le bord d’une marmite: les deux
crochets latéraux du support sont prévus à cet effet.
2. Placer la grille, les 3 encoches face aux 3 tétons, et la
tourner légèrement sans qu’il soit utile de le serrer.
3. L’ensemble arbre - manivelle - traverse se centre alors sur
te pivot de la grille et sa bloque à l’emplacement prévu à
l’aide des deux ressorts de fi xation disposés de chaque
côté du cône.
Les 2 étriers de la traverse maintiennent les 2 ressorts.
Le Moulin est prêt à servir
DÉMONTAGE
1. Appuyer sur les deux ressorts de fi xation, les étriers de la
traverse tombent d’eux-mêmes. Sortir l’Arbre en le tournant
dans le sans de rotation afi n d’éviter la palette d’arrêt.
2. Prendre la grille deux mains, par l’extérieur et desserrer
«d’un coup sec» dans le sens contraire au mouvement.
REMARQUE
Lorsque l’appareil est neuf, l’intérieur de la grille est très
rugueux, ce qui est un facteur d’ef cacité du MOULIN.L.T.
Aussi, il est bien évident qua lorsque l’intérieur de le grille
devient lisse, il est alors nécessaire de la remplacer.
M5002
X5002
ensemble arbre-manivelle-traverse
M5001
X5001
cone-support avec ressorts d’accrochage
M5004
X5004
cercie-support
M5010-15-20-30-40
X5010-15-20-30-40
grille
M5003
X5003
ressort d’accrochage
perforations, grandeur nature, de grilles
1 mm 1,5 mm 2 mm 3 mm 4 mm

Produktspezifikationen

Marke: Louis Tellier
Kategorie: niet gecategoriseerd
Modell: 208030

Brauchst du Hilfe?

Wenn Sie Hilfe mit Louis Tellier 208030 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung niet gecategoriseerd Louis Tellier

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung für -Kategorien-