Lockwood 8653 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Lockwood 8653 (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
Part No. 8653-221 Iss. B 0916
‘O’ Ring
Locating
Lugs
‘O’ Ring
Ensure Actuating bar
and Rods are assembled
as shown prior to assembly
to the door frame. With
the ‘TOP’ mark facing the
top of the door.
Top Lock
Locating
Lugs
Actuating
Bar
Rod
Keeping the Locating Lugs of
the Actuating bar facing the
front edge of the stile, insert
the rod assembly through
the top cut-out, and slide
it through the door
section. With the Top
lock in the locked
position, connect the
rod and push into place.
Pull bottom rod end through bottom
cut-out. Connect to Bottom Lock, and
push into place.
4
5
6
1
11
LOCKWOOD 8653 SECURITY
SLIDING 3 POINT DOOR LOCK
Mounting of the Handle below the centreline
Both sides of the door stile must be cut out to
the dimensions given. Start with the centreline
of the door.
Both sides of the door stile must be cut out to
the dimensions given. Start with the centreline
of the door.
Mounting of the Handle above the centreline
INSTALLATION INSTRUCTIONS
1a 1b
Press here
with screwdriver
Step A Ensure the lock is in the Red
“Locked” position. Gently push the
bottom lock until it stops.
Drill a Ø3mm hole in the centre
of the slot, and loosely fit the first
fixing screw.
Step B Push the lock towards the
bottom of the door, tighten the
first screw.
Check the beak position as per
Step 4. Unlock and lock the
main lock to check operation.
Ensure the lock is in the Red
“Locked” position, drill and
fasten the second
screw.
Installation of Bottom Auxilary Lock
B
A
Installation of Top Auxilary Lock
Step A Ensure the lock is in
the Red “Locked” position. Gently
push the top lock until it stops.
Drill a Ø3mm hole in the centre of
the slot, and loosely fit the first
fixing screw.
Step B Push the lock towards the
top of the door, tighten the
first screw.
Check the beak position as per
Step 4. Unlock and lock
the main lock to check operation.
Ensure the lock is in
the Red “Locked” position, drill
and fasten the second screw.
For correct function ,
the beak should remain
secure when pressure is
applied in deadlocked
state.
To check correct function,
deadlock the door and
apply downwards pressure
with a screw driver, in position
shown. If the beak releases, the lock is
now out of sync. Re-sychronise the lock and
adjust the lock slightly downwards. Deadlock,
and repeat test until the beak is secure.
Re-sychronising the Lock
If the lock is out of sync and
cannot be operated, remove
the furniture plates and
indicator assembly.
Insert a small flat head screw
driver into the indicator
mechanism as shown. Turn the
mechanism in the key locking
direction. Check the operation of the lock.
2
Checking of Top and Bottom Auxilary Locks
46
A
B
For the main lock drill two
Ø3mm holes and fit to door
jamb where marked using
12mm countersunk screws.
Adjust striker to correct
position and then tighten
screws. For timber
jambs, use longer
10g screws provided.
Repeat the process
with the top and bottom
strikers using the 8g screws
provided.
Use larger
strikers on Top
and Bottom locks
Use smaller
striker on the
Main lock
Mounting the Striker
With the strikers inserted in the
main lock body, and the top and
bottom locks, either mark the
position on the outside of the
jamb or remove the backing from
the tape and allow the strikers to
stick to the frame. Remove
strikers from locks.
35
After ascertaining the handing configuration required, simply click
the desired handle plates together and install the operating levers
and external restrictor plate as required. Then secure the furniture
plates to the door section using the two 25mm screws &
plugs supplied.
For further installation detail, reference the
standard 8653 Instructions
Restrictor plate to
External Side
Click together the External
Escutcheon Plate and the
Pull Handle, before
securing to the door
Click together the Internal
Escutcheon Plate and the
Pull Handle, before
securing to the door


Produktspezifikationen

Marke: Lockwood
Kategorie: Nicht kategorisiert
Modell: 8653

Brauchst du Hilfe?

Wenn Sie Hilfe mit Lockwood 8653 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Lockwood

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-