Livarno Lux IAN 274865 Bedienungsanleitung

Livarno Lux Nicht kategorisiert IAN 274865

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Livarno Lux IAN 274865 (108 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/108
V 1.1
English ................................................................................. 2
Dansk ................................................................................ 19
Deutsch .............................................................................. 36
LIVARNO LUX LSHB 150 B1
2 - English
Content
1. Introduction ..................................................................... 3
2. Intended use .................................................................... 3
3. Supplied items ................................................................. 4
4. Technical data .................................................................. 5
5. Safety instructions ........................................................... 6
6. Copyright ........................................................................ 9
7. Prior to use .................................................................... 10
7.1. The correct installation location ....................................................... 10
7.2. Required tools ................................................................................... 11
7.3. Prior to installation ............................................................................ 11
7.4. Assembly ........................................................................................... 12
8. First use ......................................................................... 13
8.1. Aligning the motion sensor .............................................................. 13
8.2. Setting light time (TIME) ................................................................... 14
8.3. Adjusting sensor sensitivity (SENS) ................................................. 14
8.4. Adjusting light sensitivity (LUX) ........................................................ 14
9. Cleaning / maintenance ................................................. 14
10. Troubleshooting .......................................................... 15
11. Environmental and disposal information ..................... 16
12. Conformity information ............................................... 17
13. Warranty and servicing advice .................................... 17
LIVARNO LUX LSHB 150 B1
English - 3
1. Introduction
Congratulations on the purchase of your new device. You have thus opted
for a high-quality product. The operating instructions are an integral part of
this product. They contain important information relating to safety, use and
disposal. Read all of the operating and safety instructions thoroughly
before using the product. Use the product only as described and for the
specified range of applications. Include all documents when passing on
the product to someone else.
2. Intended use
This outdoor halogen spotlight is not designed for commercial application.
It is suitable for indoor and outdoor use. The 120 watt halogen light bulb
(9) provides good illumination. The motion sensor detects movements and
the outdoor halogen spotlight automatically switches itself on and off as a
result. This device meets all relevant norms and standards in conjunction
with CE conformity. In the event of any modification to the outdoor
halogen spotlight that was not approved by the manufacturer, compliance
with these standards is no longer guaranteed.
LIVARNO LUX LSHB 150 B1
4 - English
3. Supplied items
ï‚· Outdoor halogen spotlight LSHB 150 B1
ï‚· 120 watt halogen light bulb
ï‚· Installation materials (2 screws and 2 plugs)
ï‚· Operating instructions and safety instructions
These operating instructions have a fold-out cover. The outdoor halogen
spotlight is illustrated with numbers on the inside cover. The numbers
indicate the following:
1 Screw (front pane)
2 Screw (wall bracket)
3 Cable junction box
4 Cable bushing
5 Screw connection (cable bushing)
6 Locking screw
7 Wall bracket
8 Motion sensor
9 Halogen light bulb
10 Front pane
11 Power cable (not supplied / home connection)
12 Screw terminal
13 LUX control
14 SENS control
15 TIME control
LIVARNO LUX LSHB 150 B1
English - 5
4. Technical data
Spotlight:
Brand: LIVARNO LUX
Model designation: LSHB 150 B1
Operating voltage: 220 – 240V~
, 50/60Hz
Protection class: I (with earth conductor)
Protection rating: IP44 (splashing water protection
category)
Operating position: vertical - spotlight at top, motion sensor
at bottom
Maximum projected light
coverage:
approx. 50m² when installed at a
height of approx. 2m
Dimensions (W x H x D): approx. 139 x 112 x 86mm
Weight: approx. 587g
Halogen light bulb:
Light bulb: halogen light bulb R7s J78
Energy efficiency class: C
Service life: approx. 2000 hours / approx. 8000
switching cycles
Luminous flux: 2200lm +/-5%
Power: 120 watts
Colour temperature: approx. 3000K +/-10%
Motion sensor:
Sensor detection angle: 180° max.
Detection range: max. 12m (detection sensitivity can be
set via control dial)
Light sensitivity: can be set via control dial
Mechanical swivelling: approx. 150° horizontal / approx.
180° vertical
Light time: approx. 10 seconds +/- 5 seconds to
12 minutes +/- 1.5 minutes
The technical data and design may be changed without notification.
LIVARNO LUX LSHB 150 B1
6 - English
5. Safety instructions
Before using this device for the first time, please
read the following instructions carefully and
take note of the safety warnings, even if you
are familiar with the use of electronic devices.
Store these operating instructions in a safe
place for future reference. If you sell or pass on
the device to someone else, be sure to always
include these operating instructions as they are
an integral part of the device.
WARNING! This symbol
indicates important information
for safe operation of the outdoor
halogen spotlight and the safety
of the user. Disregarding this
information can lead to material
damage and/or health hazards
and even death.
Fire hazard: Attach the
outdoor halogen spotlight at a
distance of at least 1m from
illuminated materials. Excessive
heat generation can cause a fire.
LIVARNO LUX LSHB 150 B1
English - 7
Any cracked protective cover
must be replaced.
The outdoor halogen spotlight
has an earth conductor. The earth
conductor (yellow/green) must
be connected to the indicated
terminal.
Electrical devices do not belong in the
hands of children. Never allow children to
use electrical devices unsupervised
Children may not recognise potential risks.
Always keep plastic packaging away
from children. It poses a suffocation risk.
If you notice any smoke, unusual noises or
strange odours, switch off the device
immediately. In such cases, the device
should not be used until it has been
inspected by authorised service personnel.
Never inhale smoke from a potential
device fire. If you have inhaled smoke,
LIVARNO LUX LSHB 150 B1
8 - English
however, consult a doctor. The inhalation
of smoke can be harmful.
The housing of the outdoor halogen
spotlight must not be damaged. There is a
risk of an electric shock if the housing is
damaged.
Do not use the outdoor halogen spotlight
in potentially explosive environments
which contain flammable gases, vapours
or dust. It poses a risk of explosion.
Never open the housing of the outdoor
halogen spotlight except to change the
halogen light bulb. The circuit must be
disconnected during all work on the
outdoor halogen spotlight, even when
changing the light bulb! There is a risk of
an electric shock if the housing is open.
You must not hang any objects on the
outdoor halogen spotlight. The housing is
not designed to carry loads. Otherwise,
the outdoor halogen spotlight could be
damaged.
LIVARNO LUX LSHB 150 B1
English - 9
Never use such optical instruments as a
magnifying glass to look directly into the
light beam. This can lead to eye injuries.
In the event of a suspected eye injury,
consult a doctor immediately.
6. Copyright
All information contained in these instructions is subject to copyright and is
provided for information purposes only. It is only permitted to copy or
duplicate data and information with the express and written consent of the
author. This also includes commercial use of the content and data. The text
and illustrations are based on the state of the art at the time of printing.
Subject to change.
LIVARNO LUX LSHB 150 B1
10 - English
7. Prior to use
Remove the outdoor halogen spotlight and the installation materials from
the packaging.
Check the outdoor halogen spotlight for signs of damage. If it is damaged,
the outdoor halogen spotlight must not be used.
Only use halogen light bulbs with R7s J78 base and a
maximum power of 150 watts!
The halogen light bulb (9) is stored within the spotlight so that it can be
transported safely. Loosen the screw (1) with a Phillips screwdriver and
carefully open the front pane (10). Take the packaging with the halogen
light bulb (9). Open the packaging, remove the halogen light bulb (9) and
press it into one side of the bulb fitting in order to then insert it into the
other side. When doing so, do not handle the halogen light bulb (9) by its
glass body. The bulb should only ever be handled with a cloth. Close the
front pane (10) now and tighten the screw (1) again.
7.1. The correct installation location
Select the installation location carefully and prepare well for the
installation.
 Place all individual parts, required tools and installation material so
they are well arranged and ready to hand.
 The outdoor halogen spotlight may be mounted only on stable
substrates, for example, brickwork.
 Do not install the outdoor halogen spotlight above a heat source or in
the immediate vicinity of other light sources. When selecting the
installation location, also pay attention to the illustration [D] on the
inside cover.
 Select the installation location so that the outdoor halogen spotlight is
protected against wind, rain and dirt.
 Find out in advance which installation material is suitable for the
installation location you selected. Suitable installation material for
concrete is included with the outdoor halogen spotlight.
LIVARNO LUX LSHB 150 B1
English - 11
7.2. Required tools
The following tools are not supplied. This list can be used for orientation.
The exact nature of the required tools depends on the individual on-site
conditions.
 Ladder
 Voltage tester
 Spirit level, folding ruler, pencil
 Drill with drill bits
 Phillips screwdriver, flat-bladed screwdriver
 Spanner, combination pliers, side cutter
7.3. Prior to installation
The installation must be performed only by an authorised
electrician!
The circuit must be switched off during the installation!
When drilling the holes, make sure that no cables or pipes in
the wall are damaged.
 Before installation, familiarise yourself with the individual parts of the
outdoor halogen spotlight as well as the text and illustrations of these
operating instructions and comply with them.
 Make sure that the cable to which the outdoor halogen spotlight is to
be connected is not live. To ensure that this is the case, remove the
appropriate circuit fuse from your fuse box or switch the fuse to the "0"
position.
 Make sure that the cable is not live using a voltage tester!
LIVARNO LUX LSHB 150 B1
12 - English
7.4. Assembly
 Detach the wall bracket (7) from the outdoor halogen spotlight by
removing the 2 screws (2) with a Phillips screwdriver. Note that the
wall bracket (7) is attached on both sides with a screw (2), a spring
washer and a nut. Keep these parts safe until you are ready to
assemble them.
 Use the wall bracket (7) as a template to mark the two holes.
 Then drill the two holes and attach the wall bracket (7) using the
supplied wall plugs and screws or, depending on the installation
location, using other suitable plugs and screws.
 Open the cable junction box (3) by loosening the four screws using a
Phillips screwdriver and removing the cover.
 Loosen the 2 screws on the strain relief within the cable junction box
(3) with a Phillips screwdriver only to the extent that the power cable
(11) can be subsequently fed through it.
 Loosen the screw connection (5) of the cable bushing (4), but do not
completely unscrew it.
 Remove approx. 5 to 8cm of the sheath of the power cable (11).
 First, route the power cable (11) through the screw connection (5)
and the cable bushing (4), and then through the strain relief in the
cable junction box (3). When routing the power cable (11) through
the cable bushing (4), an internal rubber seal must be penetrated. A
slight resistance may thus be felt.
 Fix the power cable (11) by tightening the 2 screws on the strain relief
within the cable junction box (3). The end of the cable sheath must be
in the strain relief for this purpose. Do not clamp the individual wires!
 Then tighten the previously loosened screw connection (5) of the
cable bushing (4) in a clockwise direction. This ensures the sealing of
the power cable (11).
LIVARNO LUX LSHB 150 B1
English - 13
 Connect the stripped wire ends of the power cable (11) using the
screw terminal (12). Make sure that the individual wires of the power
cable (11) are connected correctly. Also pay attention in this context
to the illustration [B] on the inside cover.
Wire Symbol Designation
Black or brown L Phase
Blue N Neutral
Yellow/green Earth conductor
 Close the cable junction box (3) by screwing the cover again tightly
with the four screws that you previously removed. A rubber seal which
is integrated in the cover ensures the sealing of the cable junction box
(3). Ensure that the rubber seal lies correctly in the groove provided in
the cover.
 Then attach the outdoor halogen spotlight to the wall bracket (7). To
do so, use the previously removed screws (2), spring washers and
nuts.
 Switch on the circuit.
8. First use
8.1. Aligning the motion sensor
Make sure that no movements that should not be detected (for
example, on the pavements or streets) occur in the detection
range of the motion sensor (8).
It is best if you set the light sensitivity of the motion sensor (8)
during the lighting conditions when the outdoor halogen spotlight
is supposed to be active.
ï‚· Align the motion sensor (8) so that it can capture the desired range as
well as possible. The view must not be obstructed by objects or anything
else.
ï‚· You can align the motion sensor (8) horizontally by turning it.
LIVARNO LUX LSHB 150 B1
14 - English
ï‚· To align the motion sensor (8) vertically, you must first loosen the
locking screw (6). If the motion sensor (8) is located in the desired
position, you must tighten the locking screw (6) again.
8.2. Setting light time (TIME)
You use the TIME control (15) at the bottom of the motion sensor (8) to set
the light time (approx. 10 seconds to 12 minutes). Turn the TIME control
(15) clockwise (+ - direction) to increase the light time or anti-clockwise (
direction) to reduce the light time.
8.3. Adjusting sensor sensitivity (SENS)
You use the SENS control (14) at the bottom of the motion sensor (8) to
adjust the sensor sensitivity. Turn the SENS control (14) clockwise (+
direction) to increase the sensitivity or anti-clockwise (- direction) to reduce
the sensitivity. The higher the sensitivity, the greater the detection range
(12 metres at the most).
8.4. Adjusting light sensitivity (LUX)
You use the LUX control (13) at the bottom of the motion sensor (8) to
adjust the light sensitivity. Here, you set the lighting conditions to which the
twilight sensor responds and thus the outdoor halogen spotlight is switched
on or off.
Turn the LUX control (13) clockwise ( direction) so that the motion
sensor (8) responds to brighter lighting conditions.
Turn the LUX control (13) anti-clockwise ( direction) so that the motion
sensor (8) responds to darker lighting conditions.
9. Cleaning / maintenance
Maintenance
The outdoor halogen spotlight does not contain any parts that require
maintenance.
LIVARNO LUX LSHB 150 B1
English - 15
Replacing the light bulb
The circuit must be disconnected during all work on the outdoor
halogen spotlight, even when changing the light bulb! There is
a risk of an electric shock!
Only use halogen light bulbs with R7s J78 base and a
maximum power of 150 watts!
Loosen the screw (1) with a Phillips screwdriver and carefully open the
front pane (10). Press the halogen light bulb into one side of the bulb
fitting in order to then remove it from the other side. Then, press a new
halogen light bulb of the same design (see "Technical data" section) into
one side of the bulb fitting in order to then insert it into the other side.
When doing so, do not handle the halogen light bulb (9) by its glass
body. The bulb should only ever be handled with a cloth. Close the front
pane (10) now and tighten the screw (1) again.
Switch on the circuit again.
Cleaning
The circuit must be disconnected during all work on the outdoor
halogen spotlight, even when cleaning it! There is a risk of an
electric shock!
Ensure that no liquid can penetrate the housing of the outdoor
halogen spotlight. There is a risk of an electric shock.
To clean the outdoor halogen spotlight, use a soft, dry cloth and never use
any solvent or cleaner that would corrode the plastic materials. Use a
slightly damp cloth for more stubborn dirt.
10. Troubleshooting
The light does not switch itself on
 The motion sensor (8) is not aligned correctly. Correct the alignment.
 The halogen light bulb (9) is faulty. Replace it.
 The electrical connection is faulty. Get an authorised electrician to
check the electrical connection.
LIVARNO LUX LSHB 150 B1
16 - English
The light switches on and off quickly
 The sensor is disturbed by extraneous light or bright reflective surfaces.
Remove the extraneous light source or the disturbing surfaces.
The light does not switch off
 Persons or objects are within the detection range of the motion sensor
(8). Remove them.
 The outdoor halogen spotlight moves in the wind, which continually
triggers the motion sensor (8). Attach the outdoor halogen spotlight
only to a stable installation location.
11. Environmental and disposal information
When the crossed out wheelie bin symbol appears on
a product, this indicates that the product is subject to
the European Directive 2012/19/EU. All old electrical
and electronic devices must be separated from normal
household waste and disposed of at designated state
facilities. The light bulb must also be disposed of
properly.
The device must not be disposed of with household or bulky waste. You
can obtain information regarding collection points or collection times via
your local administration or local disposal services.
Remember to protect the environment. Defective bulbs should not be
disposed of with household waste. They must be taken to a collection
point. You can obtain information regarding collection points via your
local administration or local disposal services.
Dispose of the packaging in an environmentally compatible manner.
Cardboard can be put out for municipal paper collections or brought to
public collection points for recycling. Films and plastic used for packaging
the device are collected by your local disposal services and disposed of in
an environmentally compatible manner.
LIVARNO LUX LSHB 150 B1
English - 17
12. Conformity information
This device meets the basic requirements and other
relevant regulations of the EMC Directive
2014/30/EU, the Low Voltage Directive
2014/35/EU, the ErP Directive 2009/125/EC and
the RoHS Directive 2011/65/EU. To obtain a
complete EU Declaration of Conformity, send an e-
mail to the following e-mail address: ce@targa.de
13. Warranty and servicing advice
Warranty of TARGA GmbH
This device is sold with three years warranty from the date of purchase.
Please keep the original receipt in a safe place as proof of purchase.
Before using your product for the first time, please read the enclosed
documentation. Should any problems arise which cannot be solved in this
way, please call our hotline. Please have the article number and, if
available, the serial number to hand for all enquiries. If it is not possible to
solve the problem on the phone, our hotline support staff will initiate further
servicing procedures depending on the fault. Within the warranty period
the product will be repaired or replaced free of charge as we deem
appropriate. No new warranty period commences if the product is
repaired or replaced. Consumables such as batteries, rechargeable
batteries and lamps are not covered by the warranty.
Your statutory rights towards the seller are not affected or restricted by this
warranty.
LIVARNO LUX LSHB 150 B1
18 - English
Service
Phone: 020 – 70 49 04 03
E-Mail: service.GB@targa-online.com
Phone: 01 - 4370121
E-Mail: service.IE@targa-online.com
Phone: 027 78 11 03
E-Mail: service.MT@targa-online.com
Phone: 02 – 20 09 025
E-Mail: service.CY@targa-online.com
IAN: 274865
Manufacturer
TARGA GmbH
Coesterweg 45
59494 SOEST
GERMANY
LIVARNO LUX LSHB 150 B1
Dansk - 19
Indhold
1. Indledning ..................................................................... 20
2. Korrekt anvendelse ....................................................... 20
3. Leveringsomfang ........................................................... 21
4. Tekniske data ................................................................ 22
5. Sikkerhedsanvisninger .................................................. 23
6. Ophavsret ..................................................................... 26
7. Før ibrugtagning ............................................................ 27
7.1. Det rigtige monteringssted ............................................................... 27
7.2. Nødvendigt værktøj ......................................................................... 28
7.3. Før monteringen................................................................................ 28
7.4. Montering ......................................................................................... 29
8. Ibrugtagning ................................................................. 30
8.1. Justering af bevægelsessensoren .................................................... 30
8.2. Indstilling af den tid lampen skal lyse (TIME) ................................. 31
8.3. Indstilling af sensorens følsomhed (SENS) ..................................... 31
8.4. Indstilling af lysfølsomhed (LUX) ...................................................... 31
9. Vedligeholdelse/rengøring ........................................... 31
10. Problemløsning ........................................................... 32
11. Miljø og bortskaffelse .................................................. 33
12. Overensstemmelse ...................................................... 34
13. Oplysninger om garanti og service .............................. 34

LIVARNO LUX LSHB 150 B1
20 - Dansk
1. Indledning
Tillykke med købet af dit nye apparat. Du har besluttet dig for et produkt
af høj kvalitet. Betjeningsvejledningen er en del af produktet. Den
indeholder vigtige anvisninger vedrørende sikkerhed, brug og
bortskaffelse. Sæt dig ind i alle betjenings- og sikkerhedsanvisninger, før
du bruger produktet. Brug kun produktet som beskrevet og til de angivne
formål. Udlever alt materiale ved overdragelse af produktet til tredjemand.
2. Korrekt anvendelse
Halogenprojektøren er ikke beregnet til erhvervsmæssig brug. Den er
egnet til udendørs og indendørs brug. Halogenpæren (9) på 120 watt
sørger for en god belysning. Bevægelsessensoren detekterer bevægelser
og får halogenprojektøren til at tænde og slukke automatisk. Apparatet
opfylder alle relevante normer og standarder i forbindelse med CE-
overensstemmelse. Hvis halogenprojektøren ændres uden godkendelse fra
producentens side, kan det ikke længere garanteres, at de pågældende
normer overholdes.

Produktspezifikationen

Marke: Livarno Lux
Kategorie: Nicht kategorisiert
Modell: IAN 274865

Brauchst du Hilfe?

Wenn Sie Hilfe mit Livarno Lux IAN 274865 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Livarno Lux

Livarno Lux

Livarno Lux IAN 451322 Bedienungsanleitung

6 September 2024
Livarno Lux

Livarno Lux IAN 439088 Bedienungsanleitung

6 September 2024
Livarno Lux

Livarno Lux HG08597A Bedienungsanleitung

6 September 2024
Livarno Lux

Livarno Lux IAN 446866 Bedienungsanleitung

5 September 2024
Livarno Lux

Livarno Lux IAN 383940 Bedienungsanleitung

3 September 2024
Livarno Lux

Livarno Lux IAN 315487 Bedienungsanleitung

21 August 2024
Livarno Lux

Livarno Lux IAN 67216 Bedienungsanleitung

21 August 2024
Livarno Lux

Livarno Lux IAN 94063 Bedienungsanleitung

21 August 2024
Livarno Lux

Livarno Lux IAN 313369 Bedienungsanleitung

21 August 2024
Livarno Lux

Livarno Lux 14149606L Bedienungsanleitung

21 August 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

BEKO

BEKO BBVM17400B Bedienungsanleitung

4 Dezember 2024
DeWalt

DeWalt DXV34PTA Bedienungsanleitung

4 Dezember 2024
DeWalt

DeWalt DCF414 Bedienungsanleitung

4 Dezember 2024
DeWalt

DeWalt DXIRFFP25 Bedienungsanleitung

4 Dezember 2024
DeWalt

DeWalt DXIR1A1A2P3 Bedienungsanleitung

4 Dezember 2024
DeWalt

DeWalt DCE450 Bedienungsanleitung

4 Dezember 2024
DeWalt

DeWalt DCMAS5713 Bedienungsanleitung

4 Dezember 2024
DeWalt

DeWalt DCMASBC1 Bedienungsanleitung

4 Dezember 2024
DeWalt

DeWalt DXKH180E Bedienungsanleitung

4 Dezember 2024
DeWalt

DeWalt DWE46150 Bedienungsanleitung

4 Dezember 2024