Lindy 40846 Bedienungsanleitung
Lindy
Beamerzubehör
40846
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lindy 40846 (4 Seiten) in der Kategorie Beamerzubehör. Dieser Bedienungsanleitung war für 52 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (November 2010)
Modular Projector Brackets
Manual
English
LINDY No. 40846, 40847, 40848 & 40849
www.lindy.com
User Manual
Thank you for purchasing the LINDY modular solution for mounting projectors in your
home, office or AV multimedia setup. Both products are universal and can support
most projectors up to a weight of 11.5Kg. The brackets and poles all have the same
black finish and also have the added benefit of a cable management system built in to
the poles.
This manual will show you how to assemble and adjust both types of bracket using
either the long or short pole. Please take note of the maximum weights supported by
the brackets to avoid any damage to your installation or equipment.
Both the long and short poles attach to the ceiling or wall in the same manner.
40846: 73 to 123cm from the wall/ceiling 31 to 41cm from the wall/ceiling 40847:
Each pole has its own cable management system. Using a conduit up the centre of
the pole you can hide unsightly power and video cables from view.
The diagram below shows how the cable is fed through the pole and can either go up
through the ceiling or out through the side of the cable cover for a tidier appearance.
Assembling the “box” bracket: 40848
The “box” bracket comes with the following pieces:
73
–
123cm
31
–
41cm
User Manual
Note: you will need to adjust the size of the “box” bracket by loosening and
tightening nuts (C) depending on the size of your projector.
Step 1
Attach 2 foam strips (G) to the underside of
the main bracket as shown. This will
protect your projector from scratching
against the metal surfaces. Connect the 4 L
pieces (D) to each corner of the main
bracket using nuts (C), washers (B) and
tighten with
spanner (H).
Step 2
Attach the foam strip (G) as shown, to
bottom bracket (E). Using nuts (C) and
washers (B), attach the first part of the
bottom bracket (E) to the L piece (D).
Step 3
Attach the last foam strip (G) to the
second bottom bracket (F). Then attach
(F) to the L pieces (D) using the nuts (C)
and washers (B). The remaining nuts and
washers are to connect the two bottom
brackets (E) as shown.
Step 4
After attaching the main bracket to the
pole you can adjust the length of the
pole and lock it with screws (A).
Adjusting the bolt with the spanner (I)
will allow you to tilt and adjust your
projector to fit your requirements.
Produktspezifikationen
| Marke: | Lindy |
| Kategorie: | Beamerzubehör |
| Modell: | 40846 |
| Tiefe: | 1230 mm |
| Produktfarbe: | Schwarz |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Lindy 40846 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Beamerzubehör Lindy
3 April 2024
5 Juni 2023
Bedienungsanleitung Beamerzubehör
- Beamerzubehör Da-Lite
- Beamerzubehör BenQ
- Beamerzubehör Manhattan
- Beamerzubehör Sony
- Beamerzubehör Optoma
- Beamerzubehör Vogel's
- Beamerzubehör Vision
- Beamerzubehör Omnitronic
- Beamerzubehör Barco
- Beamerzubehör NEC
- Beamerzubehör NewStar
- Beamerzubehör Insignia
- Beamerzubehör Projecta
- Beamerzubehör Peerless-AV
- Beamerzubehör AV:link
- Beamerzubehör Chipolino
- Beamerzubehör Chief
- Beamerzubehör Sopar
- Beamerzubehör Kanto
- Beamerzubehör Christie
- Beamerzubehör Premier Mounts
- Beamerzubehör Herma
- Beamerzubehör Tempest
- Beamerzubehör Elite Screens
- Beamerzubehör Smart Media
Neueste Bedienungsanleitung fĂĽr -Kategorien-
7 Juni 2024
7 Juni 2024
28 Mai 2024
28 Mai 2024
27 Mai 2024
26 Mai 2024
26 Mai 2024
25 Mai 2024