Lincoln Electric VIKING 2450 ADV Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lincoln Electric VIKING 2450 ADV (70 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/70
GRAPHICS MAY VARY
Operator’s Manual
VIKING TM 2450 Series ADV
Auto-Darkening Helmets
with 4C TM Technology
Register your machine:
www.lincolnelectric.com/register
Authorized Service and Distributor Locator:
www.lincolnelectric.com/locator
IM 1T0626 | D ate -2Issue Jan 2
Š Lincoln Global, Inc. All Rights Reserved.
Save for future reference
Date Purchased
Code: (ex: 10859)
Serial: (ex: U1060512345)
When this equipment is shipped, title passes to the purchaser
upon receipt by the carrier. Consequently, claims for material
damaged in shipment must be made by the purchaser against the
transportation company at the time the shipment is received.
SAFETY DEPENDS ON YOU
Lincoln arc welding and cutting equipment is designed and built
with safety in mind. However, your overall safety can be increased
by proper installation ... and thoughtful operation on your part.
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,
think before you act and be careful.
This statement appears where the information must be followed
exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed
to avoid minor personal injury or damage to this equipment.
welding materials.
USE ENOUGH VENTILA
exhaust at the arc, or b
keep the fumes and ga
your breathing zone an
IN A LARGE ROOM OR
adequate if you keep y
USE NATURAL DRAFT
from your face.
If you de velop unusual
Perhaps the welding at
should be checked.
WEAR
BODY
PROTEC
properly
(See ANS
PROTEC
flash wit
clothing
leggings
PROTEC
with pro
IN SOME AREAS, prote
BE SURE protective eq
Also, wear safety gla
AT ALL TIMES.
SPECIAL SITUATION
DO NOT WELD OR CUT
had been in contact wi
properly cleaned. This
DO NOT WELD OR CUT
precautions with ventil
highly toxic fumes or g
Additional precauti
PROTECT compressed
mechanical shocks, an
BE SURE cylinders are
electrical circuit.
REMOVE all potential f
ALWAYS HAVE FIRE F
IMMEDIATE USE AND
WARNING
CAUTION
or other reproductive harm.
• Always start and operate the engine in a
well-ventilated area.
• If in an exposed area, vent the exhaust to the outside.
• Do not modify or tamper with the exhaust system.
• Do not idle the engine except as necessary.
For more information go to
www.P65 warnings.ca.gov/diesel
WAR his proNING: T duct, when use d o l f r we ding or
cutt ucesin prg, od fumes asesor g inwhich conta
chem ca kni ls own t fo the State o Cal o seif rnia to cau
birth efects and cases cancer d , in some , . (California
Health et & Saf y odC e § 2 5 5249. et seq.)
WARNING: Cancer and Reproductive Harm
www.P65warnings.ca.gov
ARC WELDING CAN BE HAZARDOUS. PROTECT
YOURSELF AND OTHERS FROM POSSIBLE SERIOUS
INJURY OR DEATH. KEEP CHILDREN AWAY.
PACEMAKER WEARERS SHOULD CONSULT WITH
THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For
additional safety information, it is strongly recommended
that you purchase a copy of “Safety in Welding & Cutting -
ANSI Standard Z49.1” from the American Welding Society,
P.O. Box 351040, Miami, Florida 33135 or CSA Standard
W117.2. A Free copy of “Arc Welding Safety” booklet E205
is available from the Lincoln Electric Company, 22801
St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION,
MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
FOR ENGINE POWERED
EQUIPMENT.
1.a. Turn the engine off before troubleshooting
and maintenance work unless the
maintenance work requires it to be running.
1.b. Operate engines in open, well-ventilated areas or vent the engine
exhaust fumes outdoors.
arc or when the engine is running. Stop the
engine and allow it to cool before refueling to
prevent spilled fuel from vaporizing on contact
their removal is complete. Always use the greatest care when
working near moving parts.
1.f. Do not put your ha
override the gover
rods while the eng
1.g. To prevent accide
the engine or weld
disconnect the sp
as appropriate.
1.h. To avoid scalding
pressure cap whe
ELECTRI
MAGNET
BE DANG
causes localized E
and welding mach
welders having a
before welding.
which are now no
2.d. All welders should
2.d.1. Route the
them with
2.d.2. Never coil
2.d.3. Do not pla
cables. If
work cabl
2.d.4. Connect th
sible to th
2.d.5. Do not wo
1.c. Do not add the fuel near an open ame welding
2.a. Electric current o
Welding current c
2.b. EMF elds may in
2.c. Exposure to EMF 
minimize exposur
1.i. Using a generator
MINUTES.
1.j. Generator exhaust
you cannot see or
1.k. NEVER use inside
EVEN IF doors and
1.l. Only use OUTSIDE
windows, doors an
1.m. Avoid other genera
MANUAL BEFORE U


Produktspezifikationen

Marke: Lincoln Electric
Kategorie: Nicht kategorisiert
Modell: VIKING 2450 ADV

Brauchst du Hilfe?

Wenn Sie Hilfe mit Lincoln Electric VIKING 2450 ADV benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Lincoln Electric

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂźr -Kategorien-