Lightware HDMI-TP-RX50 Bedienungsanleitung

Lightware Audio-/Video-Extender HDMI-TP-RX50

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lightware HDMI-TP-RX50 (2 Seiten) in der Kategorie Audio-/Video-Extender. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Important safety instructions

Please read and keep the information in the attached safety instructions supplied with the

product before start using the device.

Introduction

The Lightware HDMI- and DVI-HDCP-TP series extenders can transmit HDMI or DVI-D

signals over two CATx cables. They fully support HDMI 1.3a signals with or without HDCP

encryption. Most of the models support RS-232 transmission and HDMI-TP-RX100RA

de-embeds digital audio from the HDMI stream and outputs via its S/PDIF connector.

Box contents

Extender unit 12V DC power adaptor

with interchangeable plugs

Additional jumper (red) for

remote power settings

Safety and warranty info,

Quick Start Guide

Front and rear views - Transmitter Legend - Transmitter

EDID

rotary switches

The rotary switches select one of the EDID memory

addresses.

Learn button Stores the EDID of the display device attached to the output

in the selected memory address, or toggle LED functions.

Status LEDs The LEDs give feedback about the state of units and video

signal.

HDMI input Connect one HDMI cable between the HDMI source and

the transmitter unit.

RS-232 port 9-pole D-sub female connector. Connect a serial cable

between the transmitter unit and the desired serial device.

USB port USB interface for rmware upgrade and LDC connection.

HDMI output Connect one HDMI cable between the local display device

and the transmitter unit.

CATx outputs Connect one or two CATx cables between the transmitter

and the receiver (or Lightware Hybrid Matrix equipped with

twisted pair input cards).

DC 12V input Connect the output of the supplied 12V DC power adaptor

or use Lightware’s rack mountable power supply unit.



For lower resolutions, with a maximum pixel clock frequency of 165 MHz and if RS-232

transmission and remote power is not necessary, one CAT cable is enough - connected to

VIDEO OUT.

Front and rear views - Receiver Legend - Receiver

EDID rotary

switch

The rotary switch selects one of the EDID memory

addresses.

Learn button Stores the EDID of the display device attached to the output

in the selected memory address, or toggle LED functions.

Status LEDs The LEDs give feedback about the state of units and video

signal.

EQ level adjust The potentiometer can be used to precisely set the right

amount of equalization in manual EQ mode.

EQ mode

selector button

Toggles between automatic and manual EQ mode. The EQ

mode status LEDs indicate which mode is currently active.

USB port USB interface for rmware upgrade and LDC connection.

RS-232 port 9-pole D-sub male connector. Connect a serial cable

between the transmitter unit and the desired serial device.

CATx input Connect one or two CATx cable(s) between the trasmitter

and the receiver (or Lightware Hybrid Matrix equipped with

twisted pair output cards).

HDMI output Connect one HDMI cable between the local display device

and the transmitter unit.

S/PDIF output Standard RCA receptacle for digital coaxial audio output.

DC 12V input Connect the output of the supplied 12V DC power adaptor

or use Lightware’s rack mountable power supply unit.

Status LEDs

LED1

LED2

LED3

LED4

Remote powering



Please check the DC power settings in TP extenders before they are switched on.

In the case of wrong jumper setting devices may be damaged!

Power source can be set by jumper for local supply with plug-in adapter, or for remote supply

through TP CATx cable. The extenders are able to receive and/or send power.

When the remote power feature is used, check the settings both ends of the TP line.



Never send power towards Lightware Matrix IO cards from TP extender units.



‘12V DC POWER ADAPTOR’ is the default setting of the jumper. If no jumper is placed

on the pins, the extender cannot be powered on.

Jumper congurations



The extenders do not have networking capabilities. Do not connect the RJ45 ports

of the extenders to a Local Area Network device or a PC. Doing so may damage the

unit!

Resolution

Pixel

clk freq.

(MHz)

RX/TX50 series RX/TX100-200 series

Cat5e

UTP

Cat6

FTP

Cat7

S/FTP

Cat5e

UTP

Cat6

FTP

Cat7

S/FTP

640x480 25.2 60 m 75 m 85 m 65 m 75 m 80 m

800x600 40.0 60 m 65 m 75 m 65 m 70 m 75 m

1024x768 65.0 55 m 65 m 75 m 60 m 65 m 75 m

1280x720p 74.4 55 m 65 m 75 m 60 m 65 m 75 m

1920x1080i 74.4 50 m 65 m 75 m 60 m 65 m 75 m

1280x1024 108.2 50 m 65 m 70 m 50 m 65 m 70 m

1400x1050 122.1 45 m 65 m 70 m 40 m 65 m 70 m

1920x1080p 149.1 30 m 55 m 65 m 30 m 60 m 65 m

1920x1200p 153.4 30 m 55 m 65 m 20 m 60 m 65 m

1600x1200 162.4 NR*30 m 45 m 55 m 55 m 65 m

1920x1080p 30 bit 20 m 25 m 35 m 50 m 60 m186.3 NR*

1920x1080p 36 bit 10 m 15 m 20 m 20 m 20 m223.6 NR*

Maximum twisted pair distances

* NR: Not recommended.



The vertical frequency for all resolutions is 60 Hz.

Powering on (only on RX/TX100-200 series)

1. After the system is complete, rstly connect the adaptor to the extenders then to the

socket.

2. At rst the extenders display the rmware version using the the upper two LEDs. The

following example shows this process for a rmware version of 1.2.4:

RED blinks once, short pause.

GREEN blinks two times, short pause.

GREEN blinks four times.

3. The attached source(s) and monitor(s) can be powered on.



If none of the LEDs light up upon power-up, the unit is most likely damaged and further

use is not advised. Please contact support@lightware.eu.

Adjusting the input equalization (only on RX100-200 series)

The amplitude of high frequency signals decreases after they pass through long distances

in copper cables. To counter-act this phenomenon, the receiver amplies the signal while

maximizing the amplitude at a certain level. Two equalization modes are available: automatic

and manual. The mode can be toggled by pressing the EQ MODE button.



It is always advised to use the automatic mode and only adjust the equalization

manually if the auto mode does not give a good result.

Serial Port (only on RX/TX100-200 series)

A serial device can be connected to the RS-232 port to use the serial data pass-through

function of the RX-TX pairs. This option is useful e.g. to connect touch panel control devices.

EDID memory (valid for TX100 and TX200R devices)

Address #00: copy of the last attached monitor’s EDID from local HDMI/DVI OUT.

Address #01..#49: factory preset EDIDs suporting various embedded audio formats.

Address #51..#99: user programmable EDID memory.

Selecting and EDID

1. Turn the EDID ADDRESS rotary switches to the desired position.

Use a at head screwdriver to change the address. The left

switch sets the tens value, the right switch gives the ones value

of the EDID.



Avoid the use of keys, coins, knives and other sharp objects.

2. The EDID Status LEDs provide feedback in SECONDARY (BLINKING) mode.

3. Now the selected EDID is reported at the HDMI/DVI INPUT.

Learning EDID

1. To see EDID status, check if the Status LEDs are in SECONDARY (BLINKING) mode.

2. Turn the EDID ADDRESS rotary switches to the desired position (addresses #51..#69).

3. Connect the sink device to the HDMI/DVI OUT.

4. Press and hold the LEARN button for approximately 2 seconds.

5. The EDID Status LEDs provide feedback in SECONDARY (BLINKING) mode:

Red blinking: the learn process failed from DDC OUT.

Green blinking: the learn process was successful from DDC OUT.



RX100R, RX100RA and RX200R devices contains EDID management feature with lower

possibilites but the process is the same as above described.

RX100R TX100R

ON BLINKING ON BLINKING

LED1 Manual cable

EQ is ON

Firmware

main version

Selected EDID

is invalid

EDID learn

failure

LED2 Auto cable

EQ is ON

Firmware

sub version

Selected EDID

is valid

EDID learn

success

LED3 Signal detected Hotplug detected- -

LED4 Hotplug detected Source connected- -

RX100RA, RX200R and RX200R

ON BLINKING

LED1 HDCP-encrypted content Selected EDID is invalid

LED2 HDMI signal is present Selected EDID is valid

LED3 Signal detected Hotplug detected on HDMI OUT(1)

LED4

RX: Auto EQ mode is ON

TX: Source connected

RX100: -

RX200: Hotplug detected on OUT2

TX200: Hotplug detected on CATx



LED functions (ON/BLINKING) can be toggled by pressing the LEARN button.

2 3 51 4 6 7

9 q8 w

Safety and

warranty

info

Quick

Start

Guide

1 2 3 54

7 96 8

12V DC POWER

ADAPT

12V RECEIVE

FROM TX

12V SEND

TO TX

DC POWER

SETTINGS:

Setting on the RX Setting on the TX / Output Board

only local adaptor only local adaptor

local adaptor + remote send only remote receive from RX

only remote receive from TX local adaptor + remote send

only local adaptor 12V DC not connected to OB

only remote receive from OB 12V DC connected to OB

PWR

Quick Start Guide

DVI-HDCP-TP-TX50, -TX100R

DVI-HDCP-TP-RX50, -RX100R

HDMI-TP-TX50, -TX100R, -TX200R

HDMI-TP-RX50R, -RX100R, -RX100RA, -RX200R

Further information

The Product brief and further information is available at www.lightware.eu.

See the section on the website of the product.Downloads

sales@lightware.eu

+36 1 255 3800

support@lightware.eu

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 2.0

19200016

Remote power options

+12

V R E

MOTE P

R S

+12V

R EM OTE P OW

RECE

IVE

+1 2V

PO WER

Produktspezifikationen

Marke:	Lightware
Kategorie:	Audio-/Video-Extender
Modell:	HDMI-TP-RX50
WLAN:	Nein
Bluetooth:	Nein
AC-Netzadapter:	Ja
Produktfarbe:	Schwarz
Übertragungstechnik:	Kabelgebunden
Material:	Metall
AC Eingangsspannung:	100 - 240 V
AC Eingangsfrequenz:	50 - 60 Hz
Gleichstrom-Anschluss (DC):	Ja
Zertifizierung:	CE
Typ:	AV-Receiver
LED-Anzeigen:	Leistung
Audio Kanäle:	7.1 Kanäle
HDCP:	Ja
Unterstützte Grafik-Auflösungen:	640 x 480 (VGA), 1920 x 1200 (WUXGA), 2048 x 1080
3D:	Ja
Rack-Einbau:	Ja
Externes Netzteil:	Ja
Maximale Auflösung:	2048 x 1080 Pixel
HDMI-Version:	1.3a
Eingangsstrom:	1 A
Anzahl der HDMI-Ausgänge:	1
Maximal mögliche Übertragungsstrecke:	65 m
unterstütze Kabeltypen:	Cat5, Cat6, Cat7
Bandbreite:	6.75 Gbit/s
Empfängerdimensionen (B x T x H):	98 x 67 x 25 mm
Empfängergewicht:	230 g
RJ-45-Eingangsanschlüsse:	1
Erweiterte Display-Identifikationsdaten (EDID):	Nein
HDCP-Durchschleifung:	Ja
Betriebsspannung (Empfänger):	12 V
RS-232-Durchschleifung:	Nein
Ethernet/LAN:	Ja
Frontsteuerung (RX):	Nein
Automatischer TP-Kabelausgleich:	0 - 40 dB