Lectrosonics DNT16i Bedienungsanleitung
Lectrosonics
Prozessor
DNT16i
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr Lectrosonics DNT16i (20 Seiten) in der Kategorie Prozessor. Dieser Bedienungsanleitung war fĂźr 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/20
DNT Series
DNT16i/DNT0212 Network Processors
INSTALLATION AND STARTUP GUIDE
Rio Rancho, NM, USA
www.lectrosonics.com
Fill in for your records:
Serial Number:
Purchase Date:
A trademark of Audinate Pty Ltd.
DNT Digital Processor
LECTROSONICS, INC.
2
Installation and Quick Start Guide
Rio Rancho, NM 3
Table of Contents
FCC Part 15 Compliance 3 .......................................................
Important
Safety Instructions 4 .........................................................
Overview 5 .................................................................................
What is Dante? 5 ....................................................................
About the DNT Processors 5 ..................................................
Switched and Redundant Modes 5 .........................................
DNT16i Front Panel 6 ................................................................
DNT16i Rear Panel 6 .................................................................
DNT0212 Front Panel 7 .............................................................
DNT0212 Rear Panel 7 ..............................................................
DNT Control Panel Software 8 .................................................
DNT Software Installation 8 .....................................................
About Dante Software 9 ...........................................................
DanteTM Software
Installation 9 ......................................................................
Mandatory Settings 10 .............................................................
Dante Controller Software - Network Settings 10 ...................
DNT Control Panel Software - Signal Flow ConďŹguration 11 ..
DNT Software - USB Connection 11 .......................................
DNT Software - Ethernet Connection 11 ................................
Hardware Connections 12 .......................................................
Installing the chassis into a rack 12 ........................................
Connecting via USB for the First Time 12 ...............................
Setup and Control Port Connections 12 .................................
Programmable Inputs 13 .........................................................
RS-232 Serial Port Wiring 13 ..................................................
CrestronÂŽ RS-232 Port Wiring 13 ............................................
Programmable Outputs 13 ......................................................
Network and PC Connections 14 ............................................
Signal Routing 15 .....................................................................
Replacement Parts and Accessories 16 .................................
Service and Repair 17 ..............................................................
Returning Units for Repair 17 .................................................
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. The equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
⢠Reorient or relocate the receiving antenna
⢠Increase the separation between the equipment and receiver
⢠Connect the equipment into an outlet on a circuit different from that which the receiver is
connected
⢠Consult the dealer or an experienced radio/TV technician for help
Changes or modiďŹcations to this equipment not expressly approved by Lectrosonics, Inc. could
void the userâs authority to operate it.
Produktspezifikationen
| Marke: | Lectrosonics |
| Kategorie: | Prozessor |
| Modell: | DNT16i |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Lectrosonics DNT16i benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Prozessor Lectrosonics
5 September 2024
3 September 2024
3 September 2024
Bedienungsanleitung Prozessor
- Prozessor Asus
- Prozessor HP
- Prozessor Roland
- Prozessor Yamaha
- Prozessor Black And Decker
- Prozessor Pyle
- Prozessor Golden Age Project
- Prozessor Bose
- Prozessor Shure
- Prozessor Zoom
- Prozessor TOA
- Prozessor Lenovo
- Prozessor AMD
- Prozessor Alpine
- Prozessor Rupert Neve Designs
- Prozessor Lexicon
- Prozessor Fujitsu
- Prozessor TC Helicon
- Prozessor Digitus
- Prozessor DataVideo
- Prozessor Allen & Heath
- Prozessor Arturia
- Prozessor Warm Audio
- Prozessor Bogen
- Prozessor DBX
- Prozessor Hikvision
- Prozessor Radial Engineering
- Prozessor ART
- Prozessor Fredenstein
- Prozessor LD Systems
- Prozessor Summit Audio
- Prozessor Black Lion Audio
- Prozessor Solid State Logic
- Prozessor Chandler
- Prozessor Helix
- Prozessor Phoenix Gold
- Prozessor AMX
- Prozessor Siig
- Prozessor Amiko
- Prozessor Rane
- Prozessor Intel
- Prozessor RGBlink
- Prozessor Smart-AVI
- Prozessor Neutrik
- Prozessor Gefen
- Prozessor Christie
- Prozessor Atlas Sound
- Prozessor Eventide
- Prozessor KanexPro
- Prozessor SPL
- Prozessor BZBGear
- Prozessor AudioThing
- Prozessor Metric Halo
- Prozessor Sonifex
- Prozessor Manley
- Prozessor Lindell Audio
- Prozessor BSS Audio
- Prozessor Ashly
- Prozessor Heritage Audio
- Prozessor Matrox
- Prozessor Drawmer
- Prozessor Vivolink
- Prozessor MuxLab
- Prozessor Avenview
- Prozessor Datapath
- Prozessor SEADA
- Prozessor CEDAR
- Prozessor Mathew Lane
- Prozessor Dangerous Music
- Prozessor Empirical Labs
- Prozessor FabFilter
- Prozessor Henry Engineering
- Prozessor MyMix
Neueste Bedienungsanleitung fĂźr -Kategorien-
2 Oktober 2024
27 September 2024
21 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024