König TVS-KN-AVS500 Bedienungsanleitung

König Nicht kategorisiert TVS-KN-AVS500

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für König TVS-KN-AVS500 (36 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/36
Please carefully read the following assembly,
installation and safety instructions for brackets.
Proper installation procedure should only be performed by an expert. Failure to do so
could result in serious personal injury.
This package includes all the mouting materials. Make sure that none of these parts
are missing or damaged before beginning the mounting. If there any parts missing or
damaged, please stop and contact your Brackets dealer.
Mounting Surface
The enclosed accessories are only suitable for mounting to a ceiling or wall made of
solid concrete or wood studs. Do not install to sheet rock or wood panel.
Make sure that the ceiling and/or wall can mount a redundant weight factor of 3 times
the total weight of the equipment you intend to support overhead or on the wall.
Be aware of the weight of the equipment, and the potential for personal injury or damage
to the equipment if it is not adequately mounted.
General Guidelines
Carefully determine the position you wish to mount the bracket and its distance from
the screen. For TV sets the distance should be approximately 3x screen diameter. For
projectors it is important to know the lens to screen distance (See projector specifi cations
for set up).
Attach the plate to the ceiling using all Lag Bolts as shown in the manual pages of the
model you are using.
Warning! Tighten Lag Bolts until the wall plate is fi rmly against the wall. DO NOT OVER
TIGHTEN!
Tighten all nuts with the included wrench.
Make sure the TV of Project bracket is mounted high enough to ensure people can
easily walk under it or walk by.
Be sure to check you have mounted the appliance securely, so it will not fall.
Make sure that the electric cord of the TV-Set or Projector is going straight to the
socket without hanging. In case you have spare cord, roll it and rmly attached it to the
extension tube with tape.
One month after installation and every six months after that, check that the TV-Set or
Projector mount is securely fastened to the wall or ceiling and that the screws and nuts
are not loosening. In case of loosening, tighten all the points that have loosend.
For further assistance please call your local dealer or distributor shown on the invoice or
delivery note.
Please keep the mounting instructions for later use or questions.
Failure to do any of the above may result in failure and could be dangerous.
ENGLISH
2
Installation procedure
Step 1:
Invert the display and place it on a soft and at surface. Locate the mounting points on
the back of the display.
Many LCD manufacturers conform to VESA standards. The VESA standard defi nes
the physical mounting interfaces. The conforms to VESA 75/100/200/400 LCD mount
patterns.
monitors come with a random set of holes.Plasma
Note! Do not over tighten the screws. This may cause damage to the display or
bracket.
Before you begin, determine the desired mounting location.
Step 2:
Assemble the wall plate using the hardware and wrenches provided.
Note! Tighten screws uniformly to prevent distortion that might affect the assembly
process. Do not tighten with excessive force. Failure to follow these instructions may
cause excessive stress to the screws, greatly reducing their strength.
Solid concrete wall assembly: Carefully inspect the area where the LCD\Plasma\
Projector mount is to be installed. Check for any damage or loose cement.
Caution! When drilling holes in a cement wall or wooden studs, be absolutely sure there
are no water pipes or electrical wiring behind the wall. Use the wall plate to mark the
positions of the drilling holes.
Drill holes 3deep using a (10 mm) masonry drill bit. Insert the plastic anchors into the
hole and tap ush until the washer is even with the concrete surface. Place the back plate
onto the concrete surface and slowly tighten each nut onto its respective anchor.
Wood studs assembly:
Use a stud sensor (sold separately) to locate framing near the desired mounting position.
Note! Framing beams are typically 1-1/2”- 2 wide and spaced 16” on center. We
recommend locating more than one stud to nd a trend in stud spacing. Using a sharp
device penetrate the drywall to identify the true center of the stud. Using the wall plate
base as a template, position the wall plate base vertically. Mark the hole position on
the wall, making sure you use the center screw holes. Use a level to check horizontal
alignment of marks.
Step 3:
For tilting models, gently pull the left and the right upper edges of the display to extend
the mount to its desired display tilting angle. Using a Phillips screwdriver, adjust the tilt
mechanism to its desired position. LCD mount models are designed to maintain their
tilting angle by using nger tips on the back of the monitor. Keeping the display far from
the tilting mechanism, turn the Philips screw to its desired angle.
Step 4:
Once the mounting of the display is completed, you can tills move the display from side to
side to optimize the fi nal position of the display. Gently slide the unit from left to right over
the steel rods on the wall plate.
3
LIMITED WARRANTY
No guarantee or liability can be accepted for any changes and modifi cations of the
product or damage caused due to incorrect use of this product.
If a claim is made under this guarantee, the bracket should be returned, with the original
purchasing document to your dealer or distributor.
This warranty does not apply to:
Over loading beyond permitted load
When the bracket is misused
Normal wear
Friction damages
Coating defects
Defects caused by loosened screws, nuts
Ceiling bracket mounted to a wall or visa versa
In case of faulty use, not stated in instructions
Modifi cation or repairs made by non authorized workshops
Damage caused by a accident
Maintenance
Only use dry cloth to clean the bracket. Do not use cleaning solvents or abrasives.
General
Designs and specifi cations are subject to change without notice.
All logos brands and product names are trademarks or registered trademarks of their
respective holders and are hereby recognized as such.


Produktspezifikationen

Marke: König
Kategorie: Nicht kategorisiert
Modell: TVS-KN-AVS500

Brauchst du Hilfe?

Wenn Sie Hilfe mit König TVS-KN-AVS500 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert König

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-