Kenwood XM65R Bedienungsanleitung

Kenwood Lautsprecher XM65R

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kenwood XM65R (6 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 26 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/6
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplier.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the
model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product.
Model XM65F Serial number
Model XM65R Serial number
© 2023 JVCKENWOOD Corporation
XM65F
XM65R
6.5” COAXIAL SPEAKERS DESIGNED AND ENGINEERED TO CONNECT
AND MOUNT TO HARLEY-DAVIDSON® RUSHMORE PLATFORM
TOURING MODEL MOTORCYCLES
INSTRUCTION MANUAL
JVCKENWOOD Corporation
US Residents Only
Register Online
Register your KENWOOD product at https://registerkenwood.us.jvckenwood.com/
Contents
Section 1: XM65F Front Speaker Installation Instructions in FLH (Batwing) Models....2
Section 2: XM65F Road Glide Specific Front Speaker Installation Instructions.............4
Section 3: XM65R Rear Speaker Installation Instructions..................................................4
Warranty Info...............................................................................................................................5
KENWOOD XM65F and XM65R speakers will work best when powered by
an amplier. They have an impedance of 2 ohm and will cause damage if
wired directly to the built-in power of a non-2 ohm stable radio.
2
Section 1 - XM65F Front Speaker Installation
Instructions in FLH (Batwing) Models
Installation procedure
1. With your ignition switch in the “OFF” position, remove your outer fairing/headlamp
assembly and set it aside. Refer to a service manual if you need help with this. NOTE:
Placing a towel on the front fender can help prevent scratches or “dings” from dropped
tools or fasteners, etc.
2. Speaker Cabinet Removal: On the brake side speaker cabinet, carefully remove the
cable going into the power port/cigarette lighter assembly. If your bike has the CB module
(mounted “sideways” on the clutch side cabinet), undo the antenna cable and main
harness. The CB module will stay attached to the clutch side cabinet when removed. Undo
the speaker wire plugs going into each cabinet (pink & pink with black stripe wires).
Safety precautionsSafety precautions
CAUTION
To avoid the risk o f human injury or propert y
damage, be sure to read and observe the following
safety precautions:
• Consult a professional technician for installing and
connecting the speaker. — Incorrect installation may
lead to trac accidents or malfunctions.
• Avoid installation where the speaker in unstable. —
Make sure that the speaker is stationary and does not
rattle. Displacement of the speaker may cause injury.
• Do not modify the speaker. — Doing so may result in
smoke or re.
• Keep the volume of sound at an optimum level. —
Not being able to hear sounds from your surroundings
can lead to trac accidents.
• In case of abnormality, stop the use and disconnect
the speaker. — If operation is continued, smoke or re
may result. Disconnect the speaker and ask servicing.
• Always wear protective eyewear during installation.
• To prevent short-circuit, keep all wiring away from
moving parts, sharp edges, cut metal, etc.
• When removing or installing the grille, be careful not
to brush the unit with the edge of the grille.
• Do not switch ON power until wiring is completed.
FOR PROPER INSTALLATION AND USE
Please read the instructions carefully before using
this speaker:
• Be careful not to accidentally kick or apply any sort of
strong impact to the speaker.
• To prevent damaging the speaker, turn o the power
of the amplier before connecting it to the speaker.
• Do not use the provided parts for other purposes
Otherwise malfunction or re hazard could result.
NOTE
Observe the following cautions to prevent damage
to the speakers:
• You cannot input the same power as “peak power”
continually.
• When the volume is set too high, the sound may be
distorted or abnormal. Reduce the volume promptly in
case of such phenomena.
Section 1 - XM65F Front Speaker Installation Instructions in FLH
(Batwing) Models - Cont.
NOTE: We STRONGLY suggest completing the speaker swap on one side and then moving
to the other side. Figures 1.1 and 1.2 have arrows that point to the factory fasteners that
will be removed to allow the cabinets to come out of the bike. Although the brake side is
shown below, fastener locations are common for both brake and clutch side cabinets.
3. Installing the New Speaker: With the cabinet removed from the bike, undo the 4
screws that hold the factory speaker to the cabinet. Carefully take o each speaker wire
by disconnecting one at a time. Take the KENWOOD speaker and attach the factory
speaker wires, noting they will only go on one way. Using the factory screws, attach the
KENWOOD speaker to the cabinet. The factory speaker grille can be left in or replaced
with the supplied metal mesh grille using the 3 factory screws on the inside of the fairing.
In the KENWOOD grille, you will see two holes and one “keyhole” where the screws go
through and into the fairing. The keyhole in the KENWOOD grille needs to be oriented so
it is closest to the radio on each side for proper tment. Using the factory grilles will cause
a slight reduction in high-frequency volume. With the grilles in place and the speaker
properly attached to the speaker cabinet, the cabinet can be re-installed.
Repeat Step 3 for the second cabinet. Plug the factory speaker wires back into the
cabinet’s speaker wires and your speakers will be ready to test. Make sure to plug the
power cable back into the power port/cigarette lighter assembly on the brake side. If your
bike has the CB module, make sure to re-install the antenna cable and main harness. Then,
re-install your fairing and windshield.
3
Figure 1.1 - Side view of
brake side cabinet
Figure 1.2 - Back view of
brake side cabinet

Produktspezifikationen

Marke: Kenwood
Kategorie: Lautsprecher
Modell: XM65R

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kenwood XM65R benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lautsprecher Kenwood

Kenwood

Kenwood KFC-X1720P Bedienungsanleitung

30 September 2024
Kenwood

Kenwood Excelon XR-1703HR Bedienungsanleitung

15 September 2024
Kenwood

Kenwood KS-5200HT Bedienungsanleitung

14 September 2024
Kenwood

Kenwood Excelon XR-1701P Bedienungsanleitung

13 September 2024
Kenwood

Kenwood KFC-C6866S Bedienungsanleitung

12 September 2024
Kenwood

Kenwood GTO938 Bedienungsanleitung

25 August 2024
Kenwood

Kenwood XM50F Bedienungsanleitung

21 August 2024
Kenwood

Kenwood KFC-XS1704 Bedienungsanleitung

14 August 2024
Kenwood

Kenwood XM50R Bedienungsanleitung

13 August 2024
Kenwood

Kenwood XM69R Bedienungsanleitung

13 August 2024

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-

Sonance

Sonance Visual Performance VP65 SST Bedienungsanleitung

16 Oktober 2024
Bowers And Wilkins

Bowers And Wilkins CWM664 Bedienungsanleitung

16 Oktober 2024
Focal

Focal Chorus 826 V Bedienungsanleitung

16 Oktober 2024
KEF

KEF Ci200ER Bedienungsanleitung

16 Oktober 2024
Steren

Steren SPK-1100BL Bedienungsanleitung

16 Oktober 2024
Aiwa

Aiwa SP-A100 Bedienungsanleitung

16 Oktober 2024
Trust

Trust GXT 628 Bedienungsanleitung

15 Oktober 2024
Pyle

Pyle PBMSPG6 Bedienungsanleitung

15 Oktober 2024
Marshall

Marshall Tufton Bedienungsanleitung

15 Oktober 2024
Sunstech

Sunstech SPUBT780 Bedienungsanleitung

15 Oktober 2024