K&M 24120 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für K&M 24120 (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
3. ASSEMBLY
24120 Speaker Wall Mount
- for loudspeakers to max. 50 kg
- equally suited for home, object and public venues
- patented expanding mandrel for a shudder-free, secure fit
- suitable for flange bushing with an internal diameter of 35-37mm
- speaker direction and tilt adjustable
1. SAFETY NOTES
- Please check the support arms prior to and after use. Please do not use damaged support arms
- Do not exceed max. central load capacity of 50 kg
- Do not use in external or damp rooms
- Please observe relevant local regulations regarding installation (could differ from the examples in section 5. A,B,C)
- Use 6 screws for mounting on a wall
- Installation must be carried out by a trained installation technician
- Only mount on a suitable wall with correct mounting materials (not included in the delivery).
- Walls which are too weak or behind which run electricity pipes, water pipes or similar are unsuitable. In case of doubt, consult a
-qualified technician.
- Regularly check the bracket to make sure it is attached tightly and that the components and screws are in god condition.
- Take care when positioning the speaker, as there is a danger of pinching
- "When using the bracket at staging and production facilities" the German Accident Prevention Regulations BGV C1 apply.
a. Connect the support section 11 to the U bracket 12:
a. - using bolt components 1-2-3-3-10-1
b. Connect the adjusting shaft to the wall plate 5 6:
b. - using bolt components 7-8-9
c. Connect support section 11 with U bracket 12 (open at top) to the
c. adjusting shaft 5:
c. - using bolt components 1-2-3-3-10-1
c. NOTE: If using the top hole of the adjusting shaft, the cantilever arm
c. will be horizontal.
d. Connect the cantilever arm 4with U bracket (open below) to the
d. adjusting shaft 5:
d. - using bolt components 1-2-3-3-10-1
e. Connect the support section with the cantilever arm 11 4:
e. - using bolt components 1-2-3-3-10-1
2. COMPONENTS - OVERVIEW
Check that all components are
present and function correctly.
4 cantilever arm
5 adjusting shaft
6 wall plate
11 support section
in the bag:
1 12 x caps, small
2 3 x bolts M6 x 60 mm
3 6 x washers, small
7 2 x washers, large
8 2 x bolts M12 x 25 mm
9 2 x caps, large
10 3 x safety nuts M6
Thank you for choosing this product. These instructions contain information about the assembly and mounting of the product and its
use. We suggest you keep the instructions in a safe place for later use.
5. EXAMPLES FOR ATTACHMENT
C. For concrete and perforated brick: grout injection anchorage
C. - WITHOUT a perforated sleeve for solid bricks and concrete.
C. - WITH a perforated sleeve for perforated brick.
C. Advantage: Attachment is free of expanding pressure, which means the bracket can be exchanged as often as required and be
C. attached close to the edge (minimum distance 100 mm).
C. The detailed instructions for mounting are on the product information leaflet.
- Position the wall plate vertically,
- mark the drill holes
- drill the holes for the rawl plugs 6 x
- - ø 8 mm for bolt anchors
- - ø10 mm for frame anchors
4. WALL MOUNT
NOTE: the bracket can be mounted in two different ways:
a. In a pre-assembled state or
b. The wall plate first and then connect the rest of the bracket to the wall plate (see section 3. ASSEMBLY - b.)6
A. Concrete wall: e.g.: bolt anchor M8 x 75 mm
A. - drill a hole, blow debris from the hole, drive in the anchor, position a washer and screw in the bolt with 20 Nm.
B. Perforated brick: e.g.: plastic frame anchor 10 x 100 mm with wood screw DIN571 ø7 x 105 mm
B. - drill a hole, blow debris from the hole, drive in the rawl plug, position the wall plate, connect with a screw and an intermediate washer.
6. USER NOTES / FUNCTION
7. TILT OF CANTILEVER ARM
- NOTE:
- To adjust the tilt, first remove the loudspeaker or ask a
- second person to hold the loudspeaker during the entire
- process.
- Remove the bolt and bolt parts from the drill hole Y
- for the adjusting shaft and the support section.
- Reconnect the support section at the required
- place on the adjusting shaft.
- There are eleven possible positions for the
- cantilever arm (see section 9. DIMENSIONS).
8. DIRECTION OF CANTILEVER ARM
- Slightly loosen the connection between the adjusting Z
- shaft and the wall plate - do not remove completely.
- Swivel the cantilever arm to the required position.
- Re-tighten the connections and press on the caps.
9. DIMENSIONS
SAFETY NOTES
- Ensure there are sufficient people to help when installing, dismantling and adjusting
-the speaker (preferably 2 technically and physically suitable people).
- Ensure the loudspeakers are suitable and
-that the connections are the right size (ø 35 mm) and quality.
- Use suitable installation equipment, e.g. a safe ladder, etc.
- Check the bracket functions correctly (e.g. correctly installed supporting section 11)
-before installing the loudspeaker.


Produktspezifikationen

Marke: K&M
Kategorie: Nicht kategorisiert
Modell: 24120

Brauchst du Hilfe?

Wenn Sie Hilfe mit K&M 24120 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert K&M

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-