JVC KS-AX4302 Bedienungsanleitung

JVC Empfänger KS-AX4302

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JVC KS-AX4302 (3 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 33 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

KS-AX4504

KS-AX4302

POWER AMPLIFIER: INSTRUCTIONS

AMPLIFICATEUR DE PUISSANCE: MANUEL D’INSTRUCTIONS

0107MNMMDWTKC

EN, FR

ENGLISH

INSTALLATION

The following illustration shows a typical installation. However, you should make adjustments

corresponding to your speciﬁ c car. If you have any questions or require information regarding

installation kits, consult your “JVC IN-CAR ENTERTAINMENT” car audio dealer or a company

supplying the kits.

A Mount this unit on a ﬁ rm surface, such as in the trunk room or under the front seat.

• Since heat is generated in the unit, do not mount it near inﬂ ammable objects. In addition,

mount it in an area that will not prevent the unit from dissipating the heat.

• Do not mount the unit in the places subject to heat: near a radiator, in a glove compartment

or in insulated areas such as under a car mat that will prevent the unit from dissipating heat.

• When mounting the unit under the front seat, make sure that adjusting the seat position will

not catch any wire of the unit.

B When mounting this unit, be sure to use the provided screws. If any other screws are used,

there is a risk of loosening the unit or damaging parts inside it.

• Before drilling holes in the trunk to install the unit, make sure that there is a sufﬁ cient space

under the trunk so that you do not drill holes in the fuel tank, etc.

• detach and rotate the Logo Plate 180 degrees, use the provided hex wrench (3 mm).To

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

For safety....

•

Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

CAUTIONS AND NOTES

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.

• This unit uses BTL (Balanced Transformerless) ampliﬁ er circuitry, i.e., ﬂ oating ground system,

so please comply with the following:

Do not connect the “ terminals of the speakers to each other. ·”

Do not connect the “ terminals of the speakers to the metal body or chassis. ·”

• Cover the unused terminals with insulating tape to prevent them from short circuiting.

•

When an extension lead is used, it should be as thick and short as possible; connect it ﬁ rmly

with insulating tape.

• Be sure to leave an appropriate space between the antenna (aerial) and the wires of this unit.

•

When replacing the fuse, only use a 25 A fuse for KS-AX4504 or a 20 A fuse for KS-AX4302.

• Do not let pebbles, sand or metallic objects get inside the unit.

•

To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off periodically.

• Listening to the tape, radio, CD or Digital Audio Player, etc. with the volume set at a high level

for a long period of time will exhaust the battery, while the engine is turned off or while the

engine is idling.

• This unit becomes very hot. Be careful not to touch the unit not only when using but for a while

after using.

DO NOT disassemble the units since there are no user serviceable parts inside.

CAUTION

To prevent short circuits while making connections, keep the battery’s negative terminal

disconnected.

• When using a power cord (purchased separately), be sure to place the 30 A fuse near the

battery as shown.

• Connect the lead wire (power cord) through which power is supplied directly to the battery’s

“ terminal only after all the other connections have been made. ª”

The proper lead wire connected to each POWER terminal is as follows.

• + B and : AWG 8 to AWG 4 (The cross section is about 8 mmGND 2 to 21 mm2.)

• REM: AWG 18 to AWG 8 (The cross section is about 0.8 mm

2 to 8 mm2.)

• If you have any questions regarding the thickness of the power cord, etc., consult your nearest

“JVC IN-CAR ENTERTAINMENT” car audio dealer.

a When you use JVC car receiver with a remote lead, connect to the REM terminal on this

unit.

b When you connect a unit without a remote lead, connect to the accessory circuit of the

car which is activated by the ignition switch. In this case, noise may occur when the car

receiver is turned on or off. To avoid this noise, do not turn on or off the car receiver itself.

You can turn on or off the car receiver along with the on/off operation of the ignition switch.

If the POWER/PROTECTOR lamp lights in red, it indicates incorrect speaker wiring or

connections (see "TROUBLESHOOTING" on page 3). Make sure to correct speaker wiring and

other connections.

TERMINAL CONNECTIONS

When making the terminal connections…

1 Peel the insulating vinyl cover of a cord 7 mm (5/ in.) to 10 mm 16

(7/ in.) long and expose the inside conductor.16

2 Loosen the hex screw in a terminal with a provided hex wrench

and insert the conductor into the terminal. Then ﬁ x the hex screw

again to secure the conductor.

Note

• The exposed conductor should be 7 mm (

5/ in.) to 10 mm (16 7/ in.) long.16

– If shorter, it may cause a poor conductivity.

– If longer, it may cause a short circuit.

• Use a proper hex wrench for each terminal.

– 4 mm: +B terminal and GND terminal

– 3 mm: Speaker terminals of KS-AX4302 and REM terminal

– 2 mm: Speaker terminals of KS-AX4504

POWER SUPPLY

LVT1696-001A

[J/E/U]

A B

SPEAKER SYSTEMS

This ampliﬁ er provides two types of speaker connections: Normal Mode and Bridge Mode. You

can choose either type of connections depending on the speakers conﬁ guration equipped on

your car.

Make sure to comply with the following notes:

• Be sure not to connect the “ terminals of the speakers to a common point. ·”

• If the ground wire is common to both left/right and front/rear speaker wirings, this unit cannot be

used. Always use the independent lead wires for the speakers to be used. In this case, redo the

wirings.

• Use the speakers with an impedance of 2 to 8 (4 to 8 when used in Bridge Mode).Ω Ω Ω Ω:

• Use the speakers which have sufﬁ cient capacity to the unit.

The proper lead wire connected to each SPEAKER OUTPUT terminal is as follows.

• KS-AX4504: AWG 18 to AWG 12 (The cross section is about 0.8 mm

2 to 3.3 mm2.)

• KS-AX4302: AWG 18 to AWG 8 (The cross section is about 0.8 mm

2 to 8 mm2.)

For KS-AX4504:

When you connect 4 speakers to the unit, down mixed signals (front and rear) are emitted

through the PRE OUT jacks.

For KS-AX4302:

Incoming signals are emitted through the PRE OUT jacks.

For Customer Use:

Enter below the Model No. and Serial No. which

are located on the top or bottom of the

cabinet. Retain this information for future reference.

Serial No.

Logo Plate (detachable)

Model No.

KS-AX4302

2-speaker system—Bridge Mode *2

4-speaker system

2-speaker system plus subwoofer—Bridge Mode *2

2-speaker system

2-speaker system (2 ampliﬁ ers)—Bridge Mode *2

Subwoofer system—Bridge Mode *2

Connection varies depending on the number of the speakers used in your car. Select the

appropriate connection referring to the following diagrams.

Before connecting: Securely connect all the parts. If the connections are loose, due to contact

resistance etc., heat will break out and may cause an accident. Secure and cover the cords with

insulating tape and run them under the car mats.

KS-AX4504

1 Not provided for this unit.

2 Bridge Mode: Be sure to connect the line output from the receiver to the left (L) jack on this

unit.

3 Be sure to connect the both leads to the target speaker lead.

å When your receiver is equipped with Line Output, connect the Line Output (through the

receiver) to the INPUT jacks on this unit.

∫ When your receiver is NOT equipped with Line Output, connect the provided speaker

input connector (through the receiver) to the HIGH INPUT terminal on this unit.

4-speaker system plus subwoofer (PRE OUT)

Down mixed signals are emitted through PRE OUT jacks.

2-speaker system plus subwoofer (PRE OUT)

SPEAKER CONNECTIONS

JVC power ampliﬁ er:

KS-AX4302, etc.

JVC power ampliﬁ er:

KS-AX4302, etc.

Subwoofer

wer lndicatorPo

The blue lamp illuminates while the unit is turned on.

POWER/PROTECTOR lamp

The lamp lights in green while the unit is turned on. When the lamp does not light or lights in

red with the unit on, it indicates there may be any trouble (see "TROUBLESHOOTING").

BASS BOOST controller

ning this boosts the 45 Hz frequency within the range of 0 dB to +12 dB. Adjust the level Tur

while listening to the sound. This control is preset to MIN when the unit is shipped.

Input LEVEL controller

The input level can be adjusted with this control when this unit is connected to other source

equipment. Adjust the level while listening to the sound. This control is preset to MIN when

the unit is shipped.

CROSSOVER ﬁ lter switch

OFF: Normally, set to this position. The switch is preset to this position when the unit is

shipped.

LPF: Set to this position when you want to turn on the LPF (Low-Pass Filter) switch (the

Low-Pass Filter transmits frequencies lower than the cutoff frequency).

HPF: Set to this position when you want to turn on the HPF (High-Pass Filter) switch (the

High-Pass Filter transmits frequencies higher than the cutoff frequency).

CROSSOVER frequency controller

ning this adjusts the cutoff frequency within the range of 50 Hz to 400 Hz. Adjust the level Tur

while listening to the sound. This control is preset to 50 Hz when the unit is shipped.

SPECIFICATIONS

Power Output KS-AX4504: 65 W RMS x 4 channels at 4 and 1% THD + NΩ ≤

KS-AX4302: 100 W RMS x 2 channels at 4 and 1% THD + NΩ ≤

Signal-to-Noise Ratio 80 dBA (reference: 1 W into 4 )Ω

TROUBLESHOOTING

For more details, consult your “JVC IN-CAR ENTERTAINMENT” car audio dealer.

The POWER/PROTECTOR lamp does not light.

• Change the fuses if the current one is blown.

• Connect the ground lead securely to a metal part of the car.

• Turn on the equipment connected to this unit.

• Use a relay if your system employs too many ampliﬁ ers.

• Conﬁ rm the battery voltage (11 V to 16 V).

The POWER/PROTECTOR lamp lights in red and/or the unit heats up abnormally.

• Use the speakers of suitable impedance.

• Correct the speaker wirings if they are short-circuited.

• Leave the unit turned off for a while to cool it down.

No sound is heard.

• Conﬁ rm the connections for power supply (see "POWER SUPPLY" on page 1).

• Connect RCA pin cords to the INPUT jacks, or the speaker input connector to the HIGH INPUT

terminal.

Alternator noise is heard.

• Keep the power cords away from the RCA pin cords.

• Keep the RCA pin cords away from other electrical cables in the car.

• Connect the ground lead securely to a metal part of the car.

• Make sure the negative speaker leads do not touch the car chassis.

• Replace the plugs or use plugs with load resistors.

• Connect a bypass capacitor across the accessory switches (horn, fan, etc.).

Noise is made when you connect the unit to an AM (MW/LW) tuner.

• Move the speaker and power cords away from the antenna (aerial) lead.

CONTROLS

Maximum Power Output 600 W

Load Impedance 4 (2 to 8 allowance)Ω Ω Ω

4 (4 to 8 allowance) (Ω Ω Ω Bridge Mode)

Frequency Response 5 Hz to 50,000 Hz* ( +0, –3 dB)

* Subsonic ﬁ lter limits extremely low frequency signals less than

20 Hz.

Input Sensitivity/Impedance 2 V/45 k (0.3 V to 6 V, variable)Ω

Distortion Less than 0.04% (at 1 kHz)

Power Requirement DC 14.4 V (11 V to 16 V allowance)

Grounding system Negative ground

Dimensions (W×H×D) 300 mm × 63 mm × 265 mm

(11-13/ in. 16

2-1/ in. 2

10-7/ in.)16

Mass (approx.) 3.8 k (8.4 lbs.)g

Accessories Speaker input connector

KS-AX4504: 8P × 1

KS-AX4302: 4P × 1

Mounting Screw ( 4 × 20 mm φ(

13/ 16

in.)

) × 4

Hex wrench

4 mm × 1

3 mm × 1

2 mm × 1 (KS-AX4504 only)

Design and speciﬁ cations are subject to change without notice.

KS-AX4302

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding

electromagnetic compatibility and electrical safety.

European representative of Victor Company of Japan, Limited is:

JVC Technology Centre Europe GmbH

Postfach 10 05 52

61145 Friedberg

Germany

Information for Users on Disposal of Old Equipment

This symbol indicates that the product with this symbol should not be

disposed as general household waste at its end-of-life. If you wish to

dispose of this product, please do so in accordance with applicable

national legislation or other rules in your country and municipality. By

disposing of this product correctly, you will help to conserve natural

resources and will help prevent potential negative effects on the

environment and human health.

This symbol is only valid in the European Union.

KS-AX4504

KS-AX4302 (For U.S.A)

2-speaker system plus subwoofer (1 ampliﬁ er)

1 Not provided for this unit.

2 Bridge wiring

3 Use a High-pass crossover (not provided).

4 Use a Low-pass crossover (not provided).

The minimum impedance should be 4 for each of left and right speakers, and the Ω

subwoofer.

Subwoofer

Produktspezifikationen

Marke:	JVC
Kategorie:	Empfänger
Modell:	KS-AX4302
Produktfarbe:	Schwarz
Impedanz:	2 Ohm
Anzahl Kanäle:	2 Kanäle
THD, totalklirren:	0.04 %
Rauschverhältnis (SNR):	80 dB
Frequenzbereich:	5 - 50000 Hz
Abmessungen (BxTxH):	300 x 265 x 63 mm
Beschreibung Ausgangsleistung:	600