JUNG 1730DD Bedienungsanleitung

JUNG Dimmer 1730DD

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JUNG 1730DD (6 Seiten) in der Kategorie Dimmer. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
LB management
LB management
LB management
LB managementLB management
Standard rotary dimmer LED
Standard rotary dimmer LED
Standard rotary dimmer LED
Standard rotary dimmer LED
Standard rotary dimmer LEDStandard rotary dimmer LED
Art. no.: 1730DD
Operating instructions
Operating instructions
Operating instructions
Operating instructionsOperating instructions
1
1
1
11 Safety instructions
Safety instructions
Safety instructions
Safety instructionsSafety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Electrical devices may only be mounted and connected by electrically skilled persons.
Electrical devices may only be mounted and connected by electrically skilled persons.
Electrical devices may only be mounted and connected by electrically skilled persons.Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Serious injuries, fire or property damage possible. Please read and follow manual fully.Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. Always disconnect before carrying out work on the devise or load.
Danger of electric shock. Always disconnect before carrying out work on the devise or load.
Danger of electric shock. Always disconnect before carrying out work on the devise or load.
Danger of electric shock. Always disconnect before carrying out work on the devise or load.Danger of electric shock. Always disconnect before carrying out work on the devise or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage. The load
Danger of electric shock. Device is not suitable for disconnection from supply voltage. The load
Danger of electric shock. Device is not suitable for disconnection from supply voltage. The load
Danger of electric shock. Device is not suitable for disconnection from supply voltage. The loadDanger of electric shock. Device is not suitable for disconnection from supply voltage. The load
is not electrically isolated from the mains even when the device is switched off.
is not electrically isolated from the mains even when the device is switched off.
is not electrically isolated from the mains even when the device is switched off.
is not electrically isolated from the mains even when the device is switched off.is not electrically isolated from the mains even when the device is switched off.
Risk of destruction if the set operating mode and load type do not match. Set correct operating
Risk of destruction if the set operating mode and load type do not match. Set correct operating
Risk of destruction if the set operating mode and load type do not match. Set correct operating
Risk of destruction if the set operating mode and load type do not match. Set correct operatingRisk of destruction if the set operating mode and load type do not match. Set correct operating
mode when connecting or exchanging the load.
mode when connecting or exchanging the load.
mode when connecting or exchanging the load.
mode when connecting or exchanging the load.mode when connecting or exchanging the load.
Fire hazard. For operation with inductive transformers, each transformer must be fused on the
Fire hazard. For operation with inductive transformers, each transformer must be fused on the
Fire hazard. For operation with inductive transformers, each transformer must be fused on the
Fire hazard. For operation with inductive transformers, each transformer must be fused on theFire hazard. For operation with inductive transformers, each transformer must be fused on the
primary side in accordance with the manufacturer's instructions. Only safety transformers ac-
primary side in accordance with the manufacturer's instructions. Only safety transformers ac-
primary side in accordance with the manufacturer's instructions. Only safety transformers ac-
primary side in accordance with the manufacturer's instructions. Only safety transformers ac-primary side in accordance with the manufacturer's instructions. Only safety transformers ac-
cording to EN 61558-2-6 may be used.
cording to EN 61558-2-6 may be used.
cording to EN 61558-2-6 may be used.
cording to EN 61558-2-6 may be used.cording to EN 61558-2-6 may be used.
These instructions are an integral part of the product, and must remain with the end customer.
These instructions are an integral part of the product, and must remain with the end customer.
These instructions are an integral part of the product, and must remain with the end customer.
These instructions are an integral part of the product, and must remain with the end customer.These instructions are an integral part of the product, and must remain with the end customer.
2
2
2
22 Intended use
Intended use
Intended use
Intended useIntended use
– Switching and dimming of lighting
– Mounting in appliance box according to DIN 49073
– Operation with suitable cover
3
3
3
33 Product characteristics
Product characteristics
Product characteristics
Product characteristicsProduct characteristics
Product characteristics
Product characteristics
Product characteristics
Product characteristicsProduct characteristics
– Device works according to the leading edge phase control or trailing edge phase control
principle
– Automatic setting of the dimming principle suitable for the load
– Operation without neutral conductor possible
– Switch-on via bulb-preserving soft start
– Switch on with last saved brightness or saved switch-on brightness
– Switch-on brightness can be saved permanently
– Minimum brightness can be saved permanently
– Electronic short-circuit protection with permanent switch-off after 7 seconds at the latest
– Electronic over-temperature protection
Power extension possible by means of power boosters.
1 / 6
82598713 04.12.2018
J0082598713
LB management
LB management
LB management
LB managementLB management
Standard rotary dimmer LED
4
4
4
44 Operation
Operation
Operation
OperationOperation
Switching light or adjusting brightness
Switching light or adjusting brightness
Switching light or adjusting brightness
Switching light or adjusting brightnessSwitching light or adjusting brightness
Figure1: Switching light or adjusting brightness
ï¿­ Press the setting knob briefly: Light switches on or off (Figure 1).
ï¿­ Turn the setting knob quickly: Brightness is changed quickly (Figure 1).
ï¿­ Turn the setting knob slowly: Brightness is changed slowly (Figure 1).
Switching the light on at minimum or maximum brightness
Switching the light on at minimum or maximum brightness
Switching the light on at minimum or maximum brightness
Switching the light on at minimum or maximum brightnessSwitching the light on at minimum or maximum brightness
Figure2: Switching on the light at minimum or maximum brightness
ï¿­ Turn the setting knob by a quarter turn, then press the setting knob briefly: Light switches
on at minimum brightness or maximum brightness (Figure 2).
Save switch-on brightness
Save switch-on brightness
Save switch-on brightness
Save switch-on brightnessSave switch-on brightness
ï¿­ Adjust the brightness.
ï¿­ Press the setting knob for longer than 4 seconds.
Switch-on brightness is saved. The lighting switches briefly off and on again as confirma-
tion.
Delete switch-on brightness
Delete switch-on brightness
Delete switch-on brightness
Delete switch-on brightnessDelete switch-on brightness
ï¿­ Press the setting knob briefly: Light switches on at the saved switch-on brightness.
ï¿­ Press the setting knob for longer than 4 seconds.
The switch-on brightness is deleted. Switching on takes place at the last brightness value
set. For confirmation, the light is switched off briefly and switched on again.
5
5
5
55 Information for electrically skilled persons
Information for electrically skilled persons
Information for electrically skilled persons
Information for electrically skilled personsInformation for electrically skilled persons
5.1
5.1
5.1
5.15.1 Fitting and electrical connection
Fitting and electrical connection
Fitting and electrical connection
Fitting and electrical connectionFitting and electrical connection
DANGER!
Mortal danger of electric shock.
Mortal danger of electric shock.
Mortal danger of electric shock.
Mortal danger of electric shock.Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
Disconnect the device. Cover up live parts.
Disconnect the device. Cover up live parts.
Disconnect the device. Cover up live parts.Disconnect the device. Cover up live parts.
2 / 6
82598713 04.12.2018
J0082598713
LB management
LB management
LB management
LB managementLB management
Standard rotary dimmer LED
Fitting and electrical connection
Fitting and electrical connection
Fitting and electrical connection
Fitting and electrical connectionFitting and electrical connection
Figure3: Connection diagram
Connect 600 Watt LED lamps or compact fluorescent lamps at most per 16ampere circuit
breaker. When connecting transformers, observe the data of the transformer manufac-
turer.
Our dimmers take into account the different electronic characteristics of most LED lamps
found on the market. However, it cannot be guaranteed that in individual cases the de-
sired results may not be achieved.
Operation without neutral conductor possible.
Figure4: Clampable conductor cross-section
Reset the overheating protection / short-circuit protection
Reset the overheating protection / short-circuit protection
Reset the overheating protection / short-circuit protection
Reset the overheating protection / short-circuit protectionReset the overheating protection / short-circuit protection
If the electronic overheating or short-circuit protection has been activated, separate the dimmer
from the grid.
5.2
5.2
5.2
5.25.2 Commissioning
Commissioning
Commissioning
CommissioningCommissioning
Setting the minimum brightness
Setting the minimum brightness
Setting the minimum brightness
Setting the minimum brightnessSetting the minimum brightness
Precondition: The dimmer is ready for operation and the load is switched off.
ï¿­ Press the setting knob for approx. 10 to 15 seconds until the light switches on and off
again.
ï¿­ Press again and hold the knob within 5 seconds. Light switches on at the lowest bright-
ness and slowly becomes brighter.
In the lowest dimming position, a lamp light must be visible.
ï¿­ Once the desired minimum brightness is reached, release the setting knob.
The minimum brightness is stored and the light is switched off.
6
6
6
66 Technical data
Technical data
Technical data
Technical dataTechnical data
Rated voltage AC 230 V~
Mains frequency 50 / 60 Hz
3 / 6
82598713 04.12.2018
J0082598713


Produktspezifikationen

Marke: JUNG
Kategorie: Dimmer
Modell: 1730DD

Brauchst du Hilfe?

Wenn Sie Hilfe mit JUNG 1730DD benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Dimmer JUNG

Bedienungsanleitung Dimmer

Neueste Bedienungsanleitung für -Kategorien-