JRC Radar1500_MKII Bedienungsanleitung

JRC Scheepsradar Radar1500_MKII

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JRC Radar1500_MKII (50 Seiten) in der Kategorie Scheepsradar. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/50
I
Thank you for purchasing the RADAR 1500 MK@ LCD radar. This
product will provide many years of trouble free use when operated
properly, so it is important that you read and observe the precau-
tions below.
Read this manual thoroughly to gain a good understanding of the capabili-
ties and the requirements of this equipment.
Store the manual in a safe location so, that it does not become lost or dam-
aged.
Observe standard storage and handling procedures for electronic equipment.
If, after proper installation, RADAR 1500 MK2 appears to be defective,
please contact your JRC sales or service representative for assistance.
Symbols Used In This Manual
The following symbols are used in this instruction manual and on the product
itself to ensure correct handling and proper use. Their meanings are explained
below. Please observe the advice and precautions emphasised by the symbols
as you read the manual and as you install and use the equipment.
Electric shocks
Prohibition
Prohibits
disassembly
Instruction
This symbol warns of the possibility of electrical and/or other related dangers.
The accompanying instructions should be meticulously followed.
This sign alerts the reader to actions which must NEVER be performed.
This sign prohibits disassembly, or otherwise tampering with the indicated com-
ponents.
This draws the reader’s attention to instructions which must be very exactly
followed.
A safety warning to alert you of possible physical harm to
yourself, or to the equipment.
An alert to possible harm to, or failure of the equipment.
II
Operating Precautions
To avoid electrical shock, never touch the inside of the scanner when
it is connected to an electrical supply.
Always keep the protective cover on the scanner when it is connected
to an electrical supply. High internal voltages can cause serious per-
sonal injury. The equipment should be routinely serviced, only by JRC
authorised personnel.
Avoid passing close to the scanner when the radar is in use.
The scanner unit rotates quickly and can cause personal injury. Both
this and the enclosed radome should be installed at a high place, such
as a cabin roof, or a specially constructed arch, or radar mast. If the
radiating units cannot be installed above all possible, standing head
height, they should be guarded by a strong, protective, enclosing frame.
Prolonged, close range exposure to radar signals is not recommended.
Before approaching close to the scanner, or dismounting it, ensure
that the STBY/OFF and the X-MIT/OFF keys on the display unit have
both been turned off. The cable connector P1 at the rear of the display
unit should be disconnected before removing the scanner unit from its
installed position.
Never sit on the scanner, nor otherwise subject them to weight. They
are not intended to bear loads and ignoring this advice could cause
damage to important internal components.
You will only get optimum performance from your RADAR 1500
MK2 by carefully following this manuals instructions. Incorrect op-
eration reduces the performance level and could cause damage to the
equipment.
Remember that radar is only an aid to navigation and can be affected
by many physical, environmental and operational factors. Radar does
not diminish the users responsibility to keep a good look out at all
times and to exercise all other navigational prudence and human judge-
ment. Radar is not a substitute for human faculties.
WARNING
CAUTION

Produktspezifikationen

Marke: JRC
Kategorie: Scheepsradar
Modell: Radar1500_MKII

Brauchst du Hilfe?

Wenn Sie Hilfe mit JRC Radar1500_MKII benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten