JL Audio VXi-BTC Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JL Audio VXi-BTC (2 Seiten) in der Kategorie Fernbedienung. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with the limits of Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
JL Audio® and the JL Audio logo are registered trademarks of JL Audio, Inc. ©2018 JLAudio, Inc. For more
detailed information please visit us online at www.jlaudio.com. Due to our policy of continuous product
development, all specications are subject to change without notice.
VXi-BTC_MAN_050718
Limited Warranty Electronics (USA)
JL Audio warrants this product to be free of defects in materials and workmanship for a period
of two (2) years from the original date of purchase. This warranty is not transferable and applies
only to the original purchaser from an authorized JL Audio dealer. Should service be necessary
under this warranty for any reason due to manufacturing defect or malfunction, JL Audio will (at
its discretion), repair or replace the defective product with new or remanufactured product at no
charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse,
product modification or neglect, failure to follow installation instructions, unauthorized repair
attempts, misrepresentations by the seller. This warranty does not cover incidental or consequen-
tial damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage
due to accident or normal wear and tear is not covered under warranty.
Warranty is void if the product’s serial number has been removed or defaced.
Any applicable implied warranties are limited in duration to the period of the express warranty
as provided herein beginning with the date of the original purchase at retail, and no warranties,
whether express or implied, shall apply to this product thereafter. Some states do not allow
limitations on implied warranties, therefore these exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights, which vary from state to state.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL Audio ’s Electronics Service Facility freight-prepaid
through an authorized JL Audio dealer and must be accompanied by proof of purchase (a copy
of the original sales receipt). Direct returns from consumers or non-authorized dealers will be
refused unless specifically authorized by JL Audio with a valid return authorization number.
Warranty expiration on products returned without proof of purchase will be determined from the
manufacturing date code. Coverage may be invalidated as this date is previous to purchase date.
Non-defective items received will be returned freight-collect. Customer is responsible for ship-
ping charges and insurance in sending the product to JL Audio. Freight damage on returns is not
covered under warranty.
For Service Information in the U.S.A. please call
JL Audio Customer Service:
(954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc.
10369 North Commerce Pkwy. Miramar, FL 33025
(Do not send product for repair to this address)
International Warranties:
Products purchased outside the United States of America are covered
only by that country’s distributor and not by JL Audio, Inc.
JLid BLUETOOTH® COMMUNICATOR
Bluetooth® Operation
Multiple devices can be paired to the VXi-BTC, however communication via
Bluetooth® is limited to one active device at a time. The VXi-BTC utilizes a top-
mounted LED control button to manage all pairing and configuration.
Pairing a new device:
1. Connect the VXi-BTC to a JLid port of a host device. The LED control
button will initialize, then flash blue.
2. Open and run TüN Mobile or TüN Express on your mobile device and open the
SELECT/RENAME DEVICE menu. (Opens automatically when app launches.)
3. Select VXi (BT) from the list of available devices, then select . (Select if a OK Pair
Bluetooth Pairing Request prompt appears on your device.) The VXi-BTC LED
ring lights solid blue, then solid green when pairing is successful. Continue
through the TüN screen prompts for VXi amplifier configuration.
4. When the SELECT/RENAME DEVICE menu is reopened and Select device
is chosen, the name of the selected BTC host device will be highlighted.
Reconnecting a paired device:
1. Open and run TüN Mobile or TüN Express on your mobile device and open the
SELECT/RENAME DEVICE menu. (Opens automatically when app launches.)
2. Select VXi (BT) from the list of available devices, then select . The VXi-OK
BTC LED ring lights solid blue, then solid green when pairing is successful.
Continue through the TüN screen prompts for VXi amplifier configuration.
Reboot/Restart:
To perform the reboot/restart function, simply cycle the host device’s power or
disconnect and reconnect the VXi-BTC from the JLid port of the host device.
Factory Reset:
Performing the Factory Reset function will remove all paired devices from
memory and restore the VXi-BTC to an original, factory default state.
1. Press and hold the LED control button for ten seconds until the LED
ring flashes white once, then release the LED control button.
2. From your device, remove/forget the VXi-BTC from its list of paired devices
before attempting to reconnect/pair the VXi-BTC with the same device.
Note: This step must be performed to avoid an error report in TüN
.
LED Control Button Status & Functionality
Refer to the table below for the meaning and functionality of the LED control button.
LED
Status
Operational
State Description Note Single Button
Press
Press/Hold
for 10
Seconds
Flashing
Blue
Open
Visibility
VXi-BTC is detect-
able and can be
paired with any
compatible device.
N/A No eect
Initiates
Factory
Reset
(see Factory
Reset
section)
Solid Blue Paired
Indicates a
successful pairing
with a device.
Switches
to Active
Connection
after pairing
Switches to
Open Visibility
state
No eect
Solid
Green
Active
Connection
Indicates a live
connection with a
paired device.
Switches to
Restricted
Visibility when
disconnected
Switches to
Restricted
Visibility state
No eect
Flashing
Green
Restricted
Visibility
VXi-BTC is detect-
able, but can only
be connected to a
previously paired
device.
N/A
Switches to
Open Visibility
state
Initiates
Factory
Reset
(see Factory
Reset
section)
Specifications
Bluetooth® Topology LE (Low Energy)
Bluetooth ®
Core Specication Version 4.2
Host Interface Proprietary VXi JLid protocol
Input Operating Voltage 5 VDC
Current Draw 50 mA (max)
Connection Range Up to 33 ft / 10 m
Placement Considerations
The VXi-BTC module should be installed in a location where it can be easily accessed for
device pairing and viewing of its status LED. While the VXi-BTC module can be mounted in
any orientation, its installation location should be considered to optimize RF performance.
For example, we recommend that you avoid mounting it directly to large metal surfaces
or to wire harnesses.
JLid
Host Device Connection Options
The VXi-BTC utilizes a proprietary JLid protocol for communicating with a host device.
Using the supplied network cable (CAT5e), all energy to power the VXi-BTC is derived
from the JLid port of a connected host device. Refer to the chart below for host
device connection options.
JLid Host Device JLid Host Device Connection Point
VXi Amplier JLid CTRL Port or
JLid
COMM Port
VXi-HUB JLid COMM Accessory Port
Note: If your mounting location exceeds the supplied cable’s length, you may use a
longer cable (not included) of the same type (CAT5e). For optimum performance, the
cable length should be kept as short as possible.
Mounting Clip Installation
A mounting clip is included to secure the VXi-BTC module. Use the supplied
screws to fasten the mounting clip to a flat surface. Once the mounting clip is
installed, attach the VXi-BTC module by pressing one side of its notched center
section against the inside of one of the arms of the mounting clip. Continue
pressing inward until both arms of the mounting clip snap around the notched
center section of the VXi-BTC module. To remove, grasp the body of the VXi-
BTC module and pull while rotating away from the mounting clip.
Product Description
The VXi-BTC is a wireless communication accessory designed to add handheld control
functionality to VXi amplifiers. Equipped with Bluetooth® LE (Low Energy), the
VXi-BTC permits wireless (up to 33 ft/10 m away) configuration of VXi amplifiers
using your compatible mobile device running TüN mobile applications. Note: The
VXi-BTC provides a control interface only and does not support audio streaming.
Mobile applications of TüN software include:
N Express – For iPhone, iPad and Android phones and tablets.
Delivers streamlined options, for fast and simple amplifier setup.
N Mobile For iPad and Android tablets. Enjoy the full-featured TüN software
experience on your tablet, with the freedom of a wireless connection.
(TüN
Express and TüN Mobile is available on the App Store and on Google Play.)
What is Included
(1) VXi-BTC Bluetooth® Communicator
(1) CAT5e Network Cable (6.5 ft./2 m)
(1) Mounting Clip
(2) Mounting Screws


Produktspezifikationen

Marke: JL Audio
Kategorie: Fernbedienung
Modell: VXi-BTC

Brauchst du Hilfe?

Wenn Sie Hilfe mit JL Audio VXi-BTC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Fernbedienung JL Audio

Bedienungsanleitung Fernbedienung

Neueste Bedienungsanleitung für -Kategorien-