JL Audio MVi-Hub Bedienungsanleitung

JL Audio Grillplatte MVi-Hub

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JL Audio MVi-Hub (2 Seiten) in der Kategorie Grillplatte. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

CONNECTION GUIDE

with

Planning Your Installation

It is important that you take the time to read this manual thoroughly and that you plan your installation

carefully. It is very easy to damage electrical systems in modern vessels. Never assume that you have found

appropriate wires without consulting a reliable wiring diagram or without using proper test equipment. If

you are uncomfortable or unfamiliar with diagrams or testing methods, please enlist the services of your

authorized JL Audio dealer to perform the installation. Your authorized dealer has the training, expertise and

installation equipment to ensure optimum performance from this product.

If you have any questions regarding the instructions in this manual or any aspect of your amplifier’s

operation, please contact your authorized JL Audio dealer for assistance. If you need further assistance,

please contact the JL Audio Technical Support Department at technical@jlaudio.com/support.

Safety Considerations

• Install this product in a dry, well-ventilated location that does not interfere with factory installed systems.

• This product should never be submerged under water or subjected to high-pressure water spray.

• Do not install where it will be directly exposed to the elements, or in the engine compartment, or in any

areas of

extreme heat. Areas exposed to a heater or hot air should also be avoided.

• When selecting a mounting location, consider the orientation of the chassis and its associated connections.

When possible, route wiring and cables to direct condensation and moisture away from the amplifier.

• Securely mount this product so that it does not come loose in the event of a collision

or sudden jolt, or as a result of repeated vibrations during normal operation.

• Check before drilling to make sure that you will not be drilling into an exterior panel/hull, fuel tank, fuel line,

wiring harness, or other vital system.

• Do not run system wiring outside or underneath the vessel. This is an extremely

dangerous practice, which can result in severe damage/injury.

• Protect all system wires from sharp edges by carefully routing them, tying

them down and using grommets and loom, where appropriate.

• Secure all wiring as needed, using cable ties or wire clamps to

protect them from moving parts and sharp edges.

What is Included

(1) MVi-HUB

(1) Connection Guide

Product Description

The MVi-HUB is an accessory designed to provide network connectivity for up to six MVi amplifiers in a multi-amp system.

Networking greatly simplifies the configuration process by permitting the setup and/or tuning of all amplifiers using a single

TüN™ project file. (See section for more info.) Additionally, networking synchronizes DSP presets of all amplifiers What is TüN?

and distributes commands from a single Digital Remote Controller (DRC) across the entire amplifier network.

The MVi-HUB includes JLid-COMM ports to connect up to six amplifiers (one “Master” MVi amplifier and up to five “Slave” MV or

MVi amplifiers). Power for the MVi-HUB is provided by the connected amplifiers. Note: a “Master” MVi amplifier connection is

required for MVi-HUB operation. The MVi-HUB utilizes a proprietary JLid™ communication protocol via standard CAT5e network

cables (not included). Use only CAT5e type network cables and keep cable lengths as short as possible for optimum performance.

Audio signals are NOT transmitted via JLid-COMM connections.

The MVi-HUB has a dedicated JLid-CTRL port for the connection of a compatible accessory (sold separately). Refer to the JLid-

CTRL Port section on the next page for additional info.

Mounting Considerations

The MVi-HUB is equipped with keyhole style mounting

holes to simplify installations in confined spaces or

vertical-mount applications. Mounting screws may be

preinstalled, allowing connections to be made prior to

securing in its final location. See diagram at right.

When selecting the installation location, consider

the mounting orientation of the MVi-HUB and its

associated connections. If possible, position the

MVi-HUB vertically, with all connections pointing

downward. Wiring and cables should be routed to

direct potential condensation and moisture away

from its chassis. When installed in this manner, the

MVi-HUB achieves an IPX2 water-resistance rating.

Limited Warranty – Electronics (USA)

JL Audio warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the original date of purchase.

This warranty is not transferrable and applies only to the original purchaser from an authorized JLAudio dealer. Should service be necessary

under this warranty for any reason due to manufacturing defect or malfunction, JL Audio will (at its discretion), repair or replace the defective

product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse,

abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller.

This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic

damage due to accident or normal wear and tear is not covered under warranty.

Products installed as original equipment by boat manufacturers are covered by the boat manufacturer’s warranty, not JLAudio, Inc.

Warranty is void if the product’s serial number has been removed or defaced.

Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein

beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to

this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not

apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

If you need service on your JL AUDIO product:

All warranty returns should be sent to JL Audio ’s Amplifier Service Facility freight-prepaid through an authorized JL Audio dealer and

must be accompanied by proof of purchase (a copy of the original sales receipt). Direct returns from consumers or non-authorized

dealers will be refused unless specifically authorized by JL Audio with a valid return authorization number. Warranty expiration on

products returned without proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated

as this date is previous to purchase date. Non-defective items received will be returned freight-collect. Customer is responsible

for shipping charges and insurance in sending the product to JL Audio. Freight damage on returns is not covered under warranty.

For Service Information in the U.S.A. please call

JL Audio Customer Service:

(954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc.

10369 North Commerce Pkwy. Miramar, FL 33025

(Do not send product for repair to this address)

International Warranties:

Products purchased outside the United States of America are covered only

by that country’s distributor and not by JL Audio, Inc.

Due to our policy of continuous product development, all specications are subject to change without notice.

MVi-HUB_MAN_070819

1 JLid-COMM Amplifier Port Connections

The MVi-HUB is equipped with one “Master” and five numbered JLid-COMM ports to connect to the JLid-COMM ports on MV

and MVi amplifiers. All JLid-COMM connections are made using standard CAT5e network cables (not included). For optimum

performance, use only CAT5e type network cables and keep cable lengths as short as possible. Refer to the table below for

connection info. When selecting the “Master” amplifier, keep in mind that the USB port on the “Master” amplifier is the connection

point for the PC or Mac® used to set up and tune the amplifiers in the network, using TüN™ software.

JLid-COMM Ports

on MVi-HUB Connection Note

JLid-COMM Master Port JLid-COMM Port of the Master MVi Amplier

(required for MVi-HUB operation)

For TüN™ configuration using a PC or Mac®, connect your

computer to the USB Port of the Master MVi amplifier only.

JLid-COMM Ports 1 to 5 JLid-COMM Port of Slave Ampliers (MV or MVi models)

2 Amp Identifier and Status LEDs

Each JLid-COMM amplifier port is outfitted with a status LED that will illuminate solid blue when connected to an amplifier.

Pressing an Amp Identifier button on the MVi-HUB will change its status LED to white and cause the top LED on the connected

amplifier to flash white. This functionality is useful for identifying specific amplifiers after installation.

3 Control Source and Status LEDs

Press the Control Source button to toggle between optional control methods. Refer to the table below for connection info.

Control Source Selection Connection Functionality

JLid-CTRL

VXi-BTC Bluetooth® Communicator Wireless conguration of an amplier network,

using a compatible device running TüN® applications

Compatible M-DRC and DRC Controllers Preset selection and level controls (varies by model)

NMEA 2000® NMEA 2000® Network Not used (TBA/future development)

4 NMEA 2000® Connection

Currently not used, this connection is intended for future NMEA® 2000 control options (TBA).

5 JLid-CTRL Port

The JLid-CTRL Port allows the connection of an optional control accessory (sold separately). Refer to the table below for compatible

accessories. For additional information, refer to the documentation included with each accessory.

JLid-CTRL Accessory Functionality Note

Digital Remote

Controller

M-DRC-50 Push-button preset selection only. Includes RGB LED ring to identify selected preset.

Only use DRC cable

for this connection

DRC-205

Remote preset selection and adjustment of levels, fader and balance. Includes RGB LED

ring to identify selected preset.

Note: This controller is not marine-rated.

Bluetooth®

Communicator VXi-BTC

Permits wireless configuration of an amplifier network, using a compatible device

running TüN™ Mobile and TüN™ Express applications. Note: The VXi-BTC provides a

control interface only and does NOT support audio streaming.

Only use CAT5e cable

for this connection

6 USB Port

The USB Port allows connection of a PC for future firmware updates to the MVi-HUB using a standard USB A/B cable (not included).

Note: For TüN™ configuration using a PC or Mac®, connect your computer to the USB Port of the “Master” MVi amplifier only.

7 Reset Buttons

Use a small pin to perform the following:

(A) Factory Reset (wipe memory, reboot MVi-HUB) - Press and hold Button A for 7 seconds. All user settings will be

erased and the MVi-HUB will revert to its factory settings!

(B) Reboot MVi-HUB - Press and release Button B to restart the MVi-HUB. Previous user settings will be retained.

10.58 in

267 mm

3.98 in

101 mm

11.21 in

285 mm

2.05 in

52 mm

Blue: White: Connected Amplif ier ID Request

REQUIRED

765

APPENDIX A: FREQUENTLY ASKED QUESTIONS

“Do I still need to send audio input signals to my amplifiers?”

Yes, audio input signals connections are required for each amplifier.

“Where do I connect my USB A/B cable for TüN™ configuration?”

Compatible computers running TüN™ software should connect to the USB Port of the Master MVi amplifier only.

“Where do I connect my DRC controller?”

Compatible DRC remote controllers should be connected to the JLid-CTRL Port of the MVi-HUB.

“Why isn’t my DRC controller working?”

Make sure JLid-CTRL has been selected using the Control Source button of the MVi-HUB.

What is TüN?

TüN™ is software that you use to configure MV or MVi amplifiers, and other JL Audio DSP products. TüN™ automatically

recognizes what it is connected to, and allows you to make adjustments with a clear interface specifically set up for that

product. TüN™ is available for download for free in a variety of applications, for computers and most handheld devices. For

more information, visit: jlaudio.com/tun

For Windows® PC or Mac® computers, TüN™ connects via USB and offers complete control and command of

the entire MV and MVi feature set from the comfort of your desk or driver’s seat. Software also runs in demo

mode, without connected amplifiers, for offline setup or demo purposes. Test drive it for free!

For iPad or Android tablets. Enjoy the TüN™ software experience on your tablet, with the freedom

of a wireless connection via Bluetooth®. Requires VXi-BTC Bluetooth® Communicator.

Wireless connection and streamlined options, for fast and simple amplifier setup. Download TüN™ Express

for iPhone, iPad and Android phones & tablets. Requires VXi-BTC Bluetooth® Communicator.

Specications

Host Interface Proprietary JLid™ protocol

Input Operating Voltage 5 VDC

IP Rating IPX2 (when mounted vertically with connections pointed downward)

Dimensions L x W x H 11.21 in x 3.98 in x 2.05 in / 285 mm x 101 mm x 52 mm

Connect to JLid-COMM Port

on each “Slave” MV or MVi

Amplier (up to ve)

Connect to JLid-COMM Port

on “Master” MVi Amplier

Connect to optional

JLid-CTRL accessory

(sold separately)

Note:

- JLid™ Network Connections are made via CAT5e Network Cables (not included)

- JLid™ Network Connections support data communication only - No Audio

- Power and Audio Input connections (not pictured) are required for each amplier.

- Components pictured may not be to scale.

For TüN™ configuration using a

PC or Mac®, connect your

computer to the USB Port of the

“Master” MVi amplifier only.

Produktspezifikationen

Marke:	JL Audio
Kategorie:	Grillplatte
Modell:	MVi-Hub

Brauchst du Hilfe?

Wenn Sie Hilfe mit JL Audio MVi-Hub benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Grillplatte JL Audio

JL Audio ETXv3 M-MCPv3-DM Bedienungsanleitung

9 September 2024

JL Audio MVi-Hub Bedienungsanleitung

28 Juli 2024

Bedienungsanleitung Grillplatte

Neueste Bedienungsanleitung für -Kategorien-

SilverCrest STYG 2000 B2 Bedienungsanleitung

9 Oktober 2024

Russell Hobbs Classics 19800-56 Bedienungsanleitung

2 Oktober 2024

CaterChef 508200 Bedienungsanleitung

1 Oktober 2024

Küppersbusch GW 30 Bedienungsanleitung

30 September 2024

Sencor SBG 2052RD Bedienungsanleitung

29 September 2024

Coyote C1C28-FS Bedienungsanleitung

24 September 2024

Coyote C1SBLP Bedienungsanleitung

24 September 2024

Tefal OptiGrill+ Initial GC706D12 Bedienungsanleitung

23 September 2024

Presto 06620 Bedienungsanleitung

22 September 2024

Coyote C2C36 Bedienungsanleitung

21 September 2024