JETI JEX-MB Bedienungsanleitung

JETI Radiografisch bestuurbaar speelgoed JEX-MB

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JETI JEX-MB (7 Seiten) in der Kategorie Radiografisch bestuurbaar speelgoed. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/7

U MSER ANUAL

MBAR EX

By JETI model s.r.o. . 11. 14 14 20

User Manual MBar EX:

-2-

C ONTENTS

1. INTRODUCTION ...................................................................................................................................... 3

2. MAIN FEATURES .................................................................................................................................... 3

3. PLACEMENT OF MBAR EX SENSOR ................................................................................................. 3

4. CONNECTING THE MBAR EX SENSOR ............................................................................................ 4

5. SETTING VIA JETIB ......................................................................................................................... 5OX

5.1 T : .............................................................................................................................. 5 HE MBAR EX SENSOR MENU

6. SETUP VIA DC/DS TRANSMITTERS .................................................................................................. 6

7. WARRANTY .............................................................................................................................................. 7

8. MBAR EX MENU DISPLAYED ON THE JETIBOX LCD: ................................................................ 7

User Manual MBar EX:

-3-

1. Introduction

MBar EX is a sensor that measures high pressures of non-corrosive and unionized gases and liquids. The

sensor records the maximum and minimum measured values of pressure and temperature. Also, it is possible to

set alarm for a high pressure measurement pressure drop. The information from the sensor is transmitted an or a

to the user via Duplex system. The EX can be used for measuring pressure in containers with EX MBar

compressed air (retractable landing gear systems) or for controlling the oil pressure in hydraulic systems.

The Duplex system takes advantage of the 2.4GHz band for communication. This system not only EX

transmits control data to the model but also sends data from the model back to the transmitter. The telemetry

data collected during operation is shown as actual, measured values in real time. The values are shown either on

the LCD screen of a connected JETIBOX or on the display of JETI model DC/DS transmitters.

2. Main features

- Measurement of pressure and temperature.

- Possible sound alarm signaling of excessive pressure or pressure drop using a JETI Tx module (EU only) or

JETIBOX profi.

- Can be used as an Expander and to connect other sensors.

- Can detect logical voltage levels on up to two inputs (e.g. detection of securing the chassis).

- The device is compatible with EX Bus protocol, i.e. it is possible to be configured comfortably via a special

menu in DC/DS JETI model transmitters.

- Firmware updates.

Technical data

MBar EX

Dimensions of the extension

Dimensions

30x23x13mm

Weight

M suring accuracy of absolute ea

pressure

±2%

Resolution of measured pressure

0,1kPa

Measurement range

0÷1000kPa (150psi, 10bar)

Operating temperature

- 10÷85°C

Recommended supply voltage

3.5 ÷ 8.4V

Maximum supply voltage

16V

Consumption

15mA

Diameter of the extension

2mm

3. Placement of MBar EX sensor

The sensor should be mounted in the model to a hard surface to prevent accidental pulling out of cables or

pressure tubing. Properly protect the sensor against the transmission of vibrations, e.g. using double-sided

adhesive tape. Use pressure tubing properly sized for the required pressure.

Attention! The sensor itself is not mechanically suited for frequent pulling out of the tubing. It is strongly

recommended to have the tubing permanently connected to the sensor. If necessary, disconnect the tubing

further away from the sensor. Failure to do so may damage the sensor.

Produktspezifikationen

Marke:	JETI
Kategorie:	Radiografisch bestuurbaar speelgoed
Modell:	JEX-MB

Brauchst du Hilfe?

Wenn Sie Hilfe mit JETI JEX-MB benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Radiografisch bestuurbaar speelgoed JETI

JETI TD1609S Bedienungsanleitung

21 August 2024

JETI JDEX-RR7 Bedienungsanleitung

21 August 2024

JETI JEX-MF2G-800 Bedienungsanleitung

21 August 2024

JETI Central Box 220 Bedienungsanleitung

21 August 2024

JETI MEZON 75 opto (RPM) Bedienungsanleitung

21 August 2024

JETI Central Box 210 Bedienungsanleitung

21 August 2024

JETI Duplex Rsat 2 EX Bedienungsanleitung

21 August 2024

JETI JEX-MU3 Bedienungsanleitung

20 August 2024

JETI MULi 6s EX Bedienungsanleitung

20 August 2024

JETI RCDroidBox Bedienungsanleitung

20 August 2024

Bedienungsanleitung Radiografisch bestuurbaar speelgoed

Neueste Bedienungsanleitung für -Kategorien-

Futaba SKYSPORT_4YBF Bedienungsanleitung

17 September 2024

Futaba 8J Bedienungsanleitung

14 September 2024

Futaba 6EX-2 Bedienungsanleitung

14 September 2024

TacTic TR325 Bedienungsanleitung

13 September 2024

Reely RaVage 4x4 V2 Bedienungsanleitung

6 September 2024

Spektrum FC6350HX Bedienungsanleitung

6 September 2024

Spektrum S250 Bedienungsanleitung

6 September 2024

Spektrum S660 Bedienungsanleitung

6 September 2024

Spektrum SPMXC2060 Bedienungsanleitung

5 September 2024

Chicco Rocket The Crossover Bedienungsanleitung

5 September 2024