JETI J-MSW-100-MS Bedienungsanleitung

JETI Funkgesteuertes Spielzeug J-MSW-100-MS

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JETI J-MSW-100-MS (8 Seiten) in der Kategorie Funkgesteuertes Spielzeug. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/8
U
SER
M
ANUAL
ELECTRONIC
SWITCH
Main Switch
By JETI model s.r.o 25. 9. 2014
User Manual: Electronic switch Main Switch
-2-
1. Introduction
Main Switch is an electronic switch designed primarily for switching of the main power supply for an RC model. It adds
an element of safety when handling the model, without the need to physically disconnect the model´s batteries. A big
advantage of electronic switches in comparison to mechanical switches is, in general, their higher reliability as far as
vibration resistance is concerned. Another advantage of the electronic switch is its ability to withstand an unlimited number
of switching cycles. Electronic switches have no moving parts like contacts which would be worn out during the switching
processes, therefore their longevity is extremely high. Moreover, they are not prone to spontaneous and unexpected false
tripping with known disastrous effects. Last but not least, electronic switches offer a much lower inherent transient
resistance in comparison to mechanical switches. The Main Switch prevents the connectors from sparking when
connecting the batteries, thus it can also replace Anti Spark plugs.
The Main Switch is shipped with a magnetic switch. The magnetic switch instructions can be found on the
manufacturer´s website. It is also possible to use the optional RC Switch instead of the magnetic switch.
The Main Switch is primarily designed for switching the main power supply of the RC models, but can also be used in
applications where switching a DC power supply is needed.
2. Connection
The power supply is connected to the Main Switch using two input wires with cross sections of 6 or 8mm
2. The output
voltage is available at two cables with cross sections of 6 or 8mm2. The output three-wire cable with the JR connector is
used for telemetry data transmission. The output three-pin connector is used to connect the supplied magnetic switch or
the RC Switch.
The Main Switch connects and disconnects the negative pole - , the + pole is always connected and is never
disconnected!
Fig. 1: Connection of input and output cables
Be sure to connect the power supply wires correctly; always connect the red cable to the + pole of the
accumulator, the black cable to the – pole of the accumulator. Pay attention when connecting outputs and inputs,
they must not be swapped. Failure to follow these requirements may result in irreversible damage to the Main
Switch!! Only connect batteries to the input IN and connect speed controllers, receivers, servos etc. to the output
OUT.
User Manual: Electronic switch Main Switch
-3-
Before switching on the electronic switch you should always connect the batteries first and only afterwards
switch on the system using the magnetic switch or the RC Switch. Follow this rule also for the switching off
procedure. Switch the system off first and disconnect the batteries only afterwards.
2.1 Connection of the Main Switch
The Main Switch measures the battery current and the voltage. If you do not need to get telemetry information from the
Main Switch, you do not have to connect the Ext. output. If you DO want to display then the telemetry the Main Switch Ext.
output must be connected to the Ext. Duplex receiver input. This also powers the measurement part of the Main Switch.
Fig. 2: Block diagram of the Main Switch
The ground (-) of the Main Switch Ext. is isolated. Do not connect the ground (-) of Magnetic switch / RC Switch to the
output ground of the Main Switch (-OUT).
2.2 Charging of the battery
The battery can be charged while connected to the Main Switch (be sure that the Main Switch is in the off state – the
green LED is off), but do not attempt to disconnect the battery while charging. The charging voltage is to be connected
directly to the battery (alternatively, to the battery through the switch input), but never connect charging voltage to the
switch output!! If it becomes necessary to disconnect the battery, disconnect the charging voltage first!! Failure to follow
these basic rules can destroy the Main Switch!!

Produktspezifikationen

Marke: JETI
Kategorie: Funkgesteuertes Spielzeug
Modell: J-MSW-100-MS

Brauchst du Hilfe?

Wenn Sie Hilfe mit JETI J-MSW-100-MS benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Funkgesteuertes Spielzeug JETI

JETI

JETI TD1609S Bedienungsanleitung

21 August 2024
JETI

JETI JDEX-RR7 Bedienungsanleitung

21 August 2024
JETI

JETI JEX-MF2G-800 Bedienungsanleitung

21 August 2024
JETI

JETI Central Box 220 Bedienungsanleitung

21 August 2024
JETI

JETI MEZON 75 opto (RPM) Bedienungsanleitung

21 August 2024
JETI

JETI Central Box 210 Bedienungsanleitung

21 August 2024
JETI

JETI Duplex Rsat 2 EX Bedienungsanleitung

21 August 2024
JETI

JETI JM-090-L Bedienungsanleitung

21 August 2024
JETI

JETI TD0905L Bedienungsanleitung

21 August 2024
JETI

JETI AddCAP 1640 Bedienungsanleitung

21 August 2024

Bedienungsanleitung Funkgesteuertes Spielzeug

Neueste Bedienungsanleitung für -Kategorien-

Proline

Proline Trencher Bedienungsanleitung

4 Oktober 2024
Futaba

Futaba 12Z Bedienungsanleitung

4 Oktober 2024
Graupner

Graupner 33718.XT60 Bedienungsanleitung

3 Oktober 2024
Amewi

Amewi Hyper Go Bedienungsanleitung

1 Oktober 2024
Carson

Carson Drift Burner Bedienungsanleitung

1 Oktober 2024
Carson

Carson Micro X-Warrior 2.0 Bedienungsanleitung

1 Oktober 2024
Biltema

Biltema 45-8119 Bedienungsanleitung

1 Oktober 2024
Traxxas

Traxxas Stampede Bedienungsanleitung

29 September 2024
Hobbywing

Hobbywing XeRun XR10 Pro WP Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing XeRun XR10 Stock Spec G2 Bedienungsanleitung

25 September 2024