Jablotron JA-80W Bedienungsanleitung
Jablotron
Sicherheit
JA-80W
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Jablotron JA-80W (1 Seiten) in der Kategorie Sicherheit. Dieser Bedienungsanleitung war fĂĽr 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/1
JA-80W wireless combined PIR + MW detector 1 MLI51101
JA-80W wireless combined PIR + MW detector
The JA-80W is a component of Jablotron’s Oasis alarm system. It is
designed to detect human body movement inside buildings. A high immunity to
false alarms is reached thanks to the combination of PIR and microwave (MW)
detection. The PIR part, if triggered, starts the MW detection to confirm PIR
activation. Only then is the triggering transmitted.
Installation
Installation shall only be undertaken by technicians holding a certificate
issued by an authorized distributor. There should be no obstacles blocking the
detector’s “view” of the protected area. Keep the detector away from metal
objects which could interfere with radio communication and the MW field.
8
Description: 1. DIP-switch; 2. MW part connector; 3.PCB tab; 4. tamper-switch; 5.
PIR sensor; 6. front cover tab; 7. MW sensitivity setting; 8. MW detector
1. Open the detector cover by pressing the tab (6) and remove the PCB
which is held by an internal tab (3) Avoid touching the internal PIR
element or damaging the antenna.
2. Punch screw holes through the rear plastic cover according to the
installation point, either for a corner or for a flat wall At least one screw
should penetrate the tamper-sensitive section.
3. Screw the rear cover to the wall, about 2.5 meters above the floor
(vertically, with the tab down).
4. Return the PCB to its original place till the tab (3) clicks..
5. Leave the battery disconnected and the cover open and then follow the
control panel or receiver manual. The basics of enrollment are:
• Enter enrollment mode on the control panel by keying in “1” in
Service mode.
• Install a battery into the detector to activate enrollment.
• Exit enrollment mode by pressing “#”
6. Close the detector cover till the tab clicks. The supplied screw can secure
the tab.
7. After installing a battery into the detector, allow three minutes for
stabilization. During this period the LED is continuously lit.
Notes:
To enroll a detector after having already connected a battery, first disconnect
the battery, and press and release the tamper switch to discharge any
remaining charge to get the device ready for enrollment.
The detector can also be enrolled by entering the serial number – the last
eights numbers of the barcode, which is placed inside the detector.
To follow the EN 50131-2-4 the tab must be secured by the supplied screw.
DIP switch Setting
Switch no.1: DEL / INS: OFF (DEL) provides entrance & exit delays for
detectors installed in a building entrance route. The ON (INS) allows the
detector to instantly trigger alarm activation if the control panel is armed.
DIP switch no.1 only has an effect if the detector has a natural reaction
assigned to it in the OASiS control panel. It also has no effect when used with
a UC-8x or AC-8x receiver.
Switch no.2: PIR NORM / HIGH: selection of immunity to false alarms.
The OFF (NORM) position combines very good immunity with fast sensor
reactions. The ON (HIGH) position gives increased immunity with a slower
reaction time and is only used for problematic installations.
Switch no.3: MW NORM / HIGH sets the time period after PIR detection in
which the MW detection is active. The position OFF – 1 s, ON – 2 s
Switch no.4: MW NORM / TEST. The position OFF is for the standard function
of the detector. The MW detection is triggered by the PIR detection part for one or
two seconds according to switch no.3. The position ON - MW detection works
continuously for testing purposes (walk test).
Testing the detector
15 minutes after closing the detector cover, the LED indicators show detector
activation. A short flash of the red light indicates PIR detection and a long flash
(2 sec) indicates MW confirmation of the movement.
For the proper functioning of the detector, it is essential to set the MW
detection field according to the place which should be monitored. For setting
up, switch the fourth DIP switch to the TEST position. Sensitivity (monitoring
range) can be adjusted by a potentiometer on the MW detection part located
inside the front cover of the detector. Turning clockwise increases the
sensitivity (range). Avoid selecting too high a sensitivity as the detection can
cover e.g. nearby rooms. Generally the MW detection field should be the same
as the PIR detection one. After setting up, switch the DIP switch back to
NORM position.
To save battery energy, the PIR detector switches to battery-save mode 15
minutes after the cover is closed. During battery-save mode the PIR sensor still
always watches out for movement. The first movement detected and consecutively
confirmed by the MW part is then signaled to the control panel instantly, and for the
next 5 minutes the PIR sensor ignores any further movement. After these 5
minutes, the PIR sensor then returns to watching out for movement until re-
triggered.
Battery replacement
The detector regularly checks its battery conditions. If battery voltage is
too low, then the report is sent to the control panel to inform the user or
installer. The detector continues to work and each detected movement is
confirmed by a brief LED flash. The battery should be replaced within two
weeks by a qualified technician in SERVICE mode.
After battery replacement, test the functioning of the detector. Expired
batteries should not be thrown into the garbage, but disposed of according
to local regulations.
Removing the detector from the system
If a detector is removed, the control panel reports the removal. The detector
has to be deleted from its address in the control panel before intentional
removal.
Detection characteristics
Technical parameters
Power supply: Lithium battery type LS(T)14500 (3.6V / 2,4 Ah AA)
Typical battery lifetime: approx. 2 years (DIP switch 3: NORM)
Communication band: 868 MHz, Oasis Protocol
Communication range: approx. 300m (open area)
Recommended installation height: 2.0 to 2.5 m above floor level
PIR detection angle/detection range: 110° / 12 m (with basic lens)
MW detection range / frequency 0.5 to 20 m / 9.35 GHz
Operational environment according to EN 50131-1 II. indoor general
Operational temperature range -10 to +40 °C
EN 50131-1, EN 50131-2-4, EN 50131-5-3 classification: grade 2
Dimensions, weight 110 x 60 x 55 mm, 140 g
Complies with ETSI EN 300220, ETSI EN 300 440-1, EN 50130-4, EN 55022, EN 60950-1
Can be operated according to ERC REC 70-03
Operation requires notification national telecommunication offices of Finland, France, Italy,
Serbia and Montenegro, Spain, Sweden, UK
JABLOTRON ALARMS a.s. hereby declares that the
JA-80W is in compliance with the essential requirements
and other relevant provisions of Directive 99/5/EC. The
original of the conformity assessment can be found at
www.jablotron.com, Technical Support section
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.
Produktspezifikationen
| Marke: | Jablotron |
| Kategorie: | Sicherheit |
| Modell: | JA-80W |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Jablotron JA-80W benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sicherheit Jablotron
23 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
20 August 2024
18 August 2024
18 August 2024
Bedienungsanleitung Sicherheit
- Sicherheit Basetech
- Sicherheit Medion
- Sicherheit Nedis
- Sicherheit Tevion
- Sicherheit Panasonic
- Sicherheit Brennenstuhl
- Sicherheit Bosch
- Sicherheit Siemens
- Sicherheit Velleman
- Sicherheit Powerfix
- Sicherheit Devolo
- Sicherheit Dymond
- Sicherheit Eminent
- Sicherheit Maginon
- Sicherheit Netgear
- Sicherheit Technaxx
- Sicherheit Alecto
- Sicherheit Gira
- Sicherheit Jacob Jensen
- Sicherheit MarQuant
- Sicherheit Topcraft
- Sicherheit Blaupunkt
- Sicherheit Grundig
- Sicherheit Trebs
- Sicherheit Alphatronics
- Sicherheit FlinQ
- Sicherheit Geemarc
- Sicherheit I-Onik
- Sicherheit Abus
- Sicherheit Elro
- Sicherheit EZVIZ
- Sicherheit Smartwares
- Sicherheit Switel
- Sicherheit Yale
- Sicherheit Steinel
- Sicherheit Easy Home
- Sicherheit Lamax
- Sicherheit Perel
- Sicherheit Fysic
- Sicherheit Goobay
- Sicherheit Fenton
- Sicherheit Waeco
- Sicherheit Honeywell
- Sicherheit B/R/K
- Sicherheit First Alert
- Sicherheit BML
- Sicherheit Doro
- Sicherheit Hagenuk
- Sicherheit Unitec
- Sicherheit IGet
- Sicherheit Juwel
- Sicherheit Theben
- Sicherheit Kopp
- Sicherheit Xavax
- Sicherheit Batavia
- Sicherheit Monacor
- Sicherheit Bavaria
- Sicherheit JUNG
- Sicherheit Ednet
- Sicherheit Nest
- Sicherheit Optex
- Sicherheit AXA
- Sicherheit Aritech
- Sicherheit Humantechnik
- Sicherheit Eufy
- Sicherheit Skytronic
- Sicherheit Audiovox
- Sicherheit Grothe
- Sicherheit Friedland
- Sicherheit DNT
- Sicherheit Sygonix
- Sicherheit LevelOne
- Sicherheit Plustek
- Sicherheit Orbis
- Sicherheit Prestigio
- Sicherheit Grandstream
- Sicherheit BTicino
- Sicherheit EasyMaxx
- Sicherheit Eden
- Sicherheit Foscam
- Sicherheit Hikvision
- Sicherheit Heidemann
- Sicherheit Somfy
- Sicherheit Dahua
- Sicherheit Dedicated Micros
- Sicherheit Dericam
- Sicherheit Directed Electronics
- Sicherheit Electronics Line
- Sicherheit Elkron
- Sicherheit Elro-Flamingo
- Sicherheit Entrya
- Sicherheit Epine
- Sicherheit FBII
- Sicherheit Fito
- Sicherheit Flamingo FA15RF
- Sicherheit Fracarro
- Sicherheit Galaxy
- Sicherheit GE Security
- Sicherheit Goliath
- Sicherheit Golmar
- Sicherheit Guardall
- Sicherheit Home Protector
- Sicherheit Home8
- Sicherheit HomeWizard
- Sicherheit I-Tel
- Sicherheit Iiquu
- Sicherheit Indexa
- Sicherheit Inner Range
- Sicherheit Interlogix
- Sicherheit Jupiter Pro
- Sicherheit Kocom
- Sicherheit Kompernass
- Sicherheit Ksenia
- Sicherheit Logicom
- Sicherheit ME
- Sicherheit Mikros
- Sicherheit Mr Safe
- Sicherheit Myfox
- Sicherheit Nemef
- Sicherheit NetBotz
- Sicherheit NetworX
- Sicherheit Niko
- Sicherheit Nor-tec
- Sicherheit Notifier
- Sicherheit One Concept
- Sicherheit One2track
- Sicherheit Oplink
- Sicherheit Paradox
- Sicherheit PIR Alarm
- Sicherheit Powermax
- Sicherheit PROmax
- Sicherheit Protector
- Sicherheit QuattSecure
- Sicherheit RISCO Group
- Sicherheit Satel
- Sicherheit SecuFirst
- Sicherheit Secure Pro
- Sicherheit Securitas
- Sicherheit Selvag
- Sicherheit Smanos
- Sicherheit Smartalarm
- Sicherheit SmartHome
- Sicherheit Sonic Alert
- Sicherheit Stobo
- Sicherheit Storage Options
- Sicherheit Storex
- Sicherheit Tegui
- Sicherheit Unitron
- Sicherheit Urmet
- Sicherheit Visonic
- Sicherheit Voxx
- Sicherheit Wanscam
- Sicherheit Woonveilig
- Sicherheit Xena
- Sicherheit Y-cam
- Sicherheit Zmodo
- Sicherheit Axis
- Sicherheit Ajax
- Sicherheit AngelEye
- Sicherheit AceSee
- Sicherheit Airbolt
- Sicherheit Alhua - Dahua
- Sicherheit Bitron Video
- Sicherheit AVTech - Velleman
- Sicherheit Bolyguard
- Sicherheit BRK DICON
- Sicherheit Bellman
Neueste Bedienungsanleitung fĂĽr -Kategorien-
5 Oktober 2024
24 September 2024
20 September 2024
19 September 2024
17 September 2024
17 September 2024
16 September 2024
16 September 2024
27 August 2024
27 August 2024