Jablotron JA-63K Bedienungsanleitung

Jablotron Sicherheit JA-63K

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Jablotron JA-63K (8 Seiten) in der Kategorie Sicherheit. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

Alarm system JA-63 „Profi“ - 8 - MGK51503

2.9 Subsystem arming

In a large building a sub control panel can be enrolled to the JA-63. The

subsystem reports all alarms and failures to the main system.

The installer can program if the systems will be armed and disarmed separately

(by their own codes and remote controls) or if the main control panel will rule the

sub control panel. Ask your installer for explanation on how to operate your

system if a sub control is panel installed.

2.10 Appliance control

The system can be used to control an electrical appliance (light, heating,

ventilation etc.). In such a case users can operate the device:

 Locally with keypad* – entering F81 (ON) or F80 (OFF).

 Remotely by phone keypad or by SMS messages – the control panel

must be equipped with GSM communicator for this feature

* Installer can program that this feature will work only when the entry is followed by a user code.

3 User’s settings

Following section is designated for the system supervisor, who knows the

master code.

All programming sequences can be terminated before completed (by N key).

3.1 New master code

The master code is used by the supervisor. The factory default master code is

1234 and you should program your own four digits code. Code programming is only

possible when the system is disarmed.

To change an existing master code enter:

F 5 xxxx yyyy yyyy

where xxxx is the existing and yyyy is the new master code (new code must be

entered twice to avoid an error).

Example:

Existing code 1234 will change to 6723 entering: F 5 1234 6723 6723

Alarm system JA-63 „Profi“ - 9 - MGK51503

3.2 User codes setting

There can be up to 14 different user codes for individual users. The system stores

to its memory which code was used for what event and when. This data can go to a

Central monitoring station as well and can also be viewed by a PC with Comlink

software.

All user codes are empty as a factory default and the supervisor should program

them entering:

F 6 xxxx yy zzzz

where xxxx is the master code, yy is the user code index (from 01 to 14) and

zzzz is the new user code.

Example:

If the master code is 1234 and the user 3 new code should be 5277 enter:

F 6 1234 03 5277

To delete a particular user code, enter 0000 as the new code (combination

0000 can not be used as a valid code).

Example:

If the master code is 1234 the user 3 code can be deleted by:

F 6 1234 03 0000

Notes:

• You can program new codes only when the system is disarmed.

• The supervisor should record the codes to the table on last page of this

manual (it should be kept hidden in a safe place).

•

• If the system is split, the supervisor can change the user codes, but can

not change to which section the particular code belongs (only the installer

can change this).

3.3 Internal clock setting

The control panel has a built in real time clock. All events are stored to the event

memory including the time & date. The clock should be set after installation, but

the supervisor can set the clock while in the user mode.

To switch the control panel to the user mode enter F 0 master code. User

mode will be indicated by a U on the keypad. To set the clock enter:

4 hh mm DD MM YY

where: hh = hours; mm = minutes; DD = day; MM = month and YY = year

Example: at 21:30 on March 19. 2005 enter: 4 21 30 19 03 04

To exit user mode press N.

Alarm system JA-63 „Profi“ - 10 - MGK51503

Actions' table

a no splitting split

0 no action no action

1 arm all arm all

2 disarm disarm all

3 partial arming arm A

4 partial arming arm B

5 disarm disarm A

6 disarm disarm B

3.4 Automatic arming / disarming

The system can automatically arm and disarm for a requested period of a day.

While in the user more, up to ten instructions (time & action) can be programmed

in the period of one day.

To switch the control panel to the user mode enter F 0 master code. User

mode will be indicated by a U on the keypad. To program automatic arming enter:

64 n a hh mm

where: n = instruction number from 0 to 9

a = action (see the actions' table)

hh = hours (from 00 to 23)

mm = minutes (from 00 to 59)

Example: to program an automatic complete

arming of the system at 21:15 everyday

enter: 64 0 1 21 15

Notes:

• If any automatic action is selected, it will be preformed everyday at the

programmed time, following the internal control panel clock.

• The automatic arming and disarming can be overridden manually anytime

(by a user code or a remote control)

• If the control panel is in the requested arming mode before the action

time, the programmed action will not change the arming

• Factory default setting - all instructions are set for no action

To exit user mode, press the N key.

3.5 Bypass

The supervisor can bypass (switch off) particular zones (potential sources of

alarms) while in the user mode. If a zone is bypassed, it can’t trigger an alarm.

To switch the control panel to the user mode enter F 0 master code. User

mode will be indicated by a U on the keypad.

To set up bypass:

1. Press key 1 to open the bypass menu.

2. With key 1 and 7 you can scroll all potential alarm sources (wireless

detectors are distinguished with the symbol ).

3. Select the source (detector, wired input…) which you want to bypass and:

a. either press key 2 for 2 seconds to bypass the source for the next

arming period (confirmed by flashing Battery LED);

b. or press key 3 for 2 seconds to bypass the source permanently

(confirmed by the Battery LED being permanently lit);

Alarm system JA-63 „Profi“ - 7 - MGK51503

2.5 Home arming

The installer can program particular detectors so that they will be automatically

bypassed in the so called “Home” partial arming. This allows for people to stay in

the particular part of the house after arming. To arm partially:

• On the keypad press home arming button

H will indicate the Home partial arming on the keypad.

To disarm a partially armed system - enter your user code or press the or

button on the remote control.

2.6 Door opening

An electrical door lock (if installed) can be controlled via the alarm system.

• Press the door opening button on the keypad to release the

lock.

2.7 Alarm memory reading

All events (arming, disarming, alarms, failures…) are recorded into the control

panel’s memory along with the time and date. The complete system history can be

viewed using a PC with Comlink software. Alarms and failures can also be viewed

on the keypad by entering:

F 4 - will show the last recorded alarm or failure. Press key 4 multiple

times to go deeper in to the memory.

2.8 Split system arming

The system can be split by the installer into two independent sections (A,B) and

a shared section (corridors, stairs, a main door…). This allows for a particular user

to arm and disarm only a particular section of the house with his/her code or

remote control (exactly as in a non split system). Arming of sections A and B is

indicated by I I symbols on the keypad. The shared section will be armed

automatically when A and B sections are both armed.

With the master code the supervisor can arm and disarm both sections. If the

master code is entered, the system will arm (if completely disarmed) or disarm (if

any section is armed).

Entering F1 master code will control only section A and F2 master code only

section B (this is true only when fast arming is disabled by the installer).

Note: partial Home arming is not possible if the system is split.

Alarm system JA-63 „Profi“ - 6 - MGK51503

2.2 Disarming

On the keypad - enter your user code

On the remote control (RC-4x) – press the button

• system will beep twice

• if there are 3 beeps, important information is indicated and will

be displayed on the keypad. Examples:

o FAILURE LED is flashing – press the N key to view the cause

o ALARM LED and zone number is flashing = alarm in the memory.

Be careful and check the house.

• if you enter the premises when the system is armed, the entrance delay

countdown will start after you trigger a delayed detector (ARM LED will

flash and beeps will sound if programmed so*).

2.3 Panic Alarm

If you are in danger you can trigger the silent panic alarm to inconspicuously call

for help. While in Panic alarm mode the control panel can send a voice message,

an SMS message and data to a central monitoring station via a telephone line

(depends on installation settings).

Panic alarm can be triggered:

• On the keypad - press the panic key and then enter your

access code.

On the remote control (RC-4x) - press the and buttons

simultaneously. The remote control can be switched (by installer) to a

Panic mode, in which pressing of any button will trigger the Panic alarm.

• By pressing this large sized panic button, the RC-22 (can be installed

on the wall, under a desk etc.).

2.4 To stop ALARM

If an alarm is triggered when you are present, you can stop it by entering your access

code or by pressing button on the remote control.

• Sending of voice and SMS messages will cease after the alarm is stopped. All

corresponding report codes (alarm triggering & stopping) will be sent to the

central monitoring station.

• If user does not stop the alarm, it will stop automatically after the programmed

period and the alarm memory indicator will activate. The control panel will

return to the same mode as before the alarm.

Alarm system JA-63 „Profi“ - 11 - MGK51503

c. multiple pressing and holding of the keys (2 or 3) will switch the

bypass on – off – on – off …

4. By repeating step 3. you can bypass all required alarm sources.

• To close the Bypass menu press the N key. If anything is bypassed when

arming, four beeps will sound and b will be displayed on the keypad during the

exit delay (and partial arming will be recorded to the memory).

• All bypasses selected with key 2 (next arming period bypasses) will switch off

automatically with the first following disarming.

• The existing bypass setting can be checked or modified in the bypass menu.

• All bypasses can be deleted by key 4 in the bypass menu. They can also be

deleted by the programming mode opening or if the control panel is

disconnected from the power completely (AC & back up battery).

To exit user mode press N.

4 Digital communicator

4.1 JA-60GSM Dialer module

If the control panel is equipped with a JA-60GSM communicator, please look at

the JA-60GSM user manual for details about user’s setting.

4.2 JA-65X Telephone communicator

If the control panel is equipped with a JA-65X telephone communicator and if

the installer enabled the supervisor to modify the communications settings, only

then will the following programming be possible.

4.2.1 Telephone numbers for voice message sending

Up to 4 telephone numbers can be programmed in the user mode. To switch the

control panel to the user mode enter F 0 master code. User mode will be

indicated by a U on the keypad.

Store telephone numbers for voice message by entering:

7 xx... xx F y

where xx...xx = telephone number

y = memory number from 1 to 4

A telephone number can have a maximum of 16 digits. A dialing pause can be

entered with F0

Note: enter a pause (F0) after the last digit of a number, which is calling a

mobile phone. This way the number will be called only once and the dialer will

not check the line signals (some mobile phone systems do not generate standard

telephone line signals).

Produktspezifikationen

Marke:	Jablotron
Kategorie:	Sicherheit
Modell:	JA-63K

Brauchst du Hilfe?

Wenn Sie Hilfe mit Jablotron JA-63K benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sicherheit Jablotron

Jablotron EYE-02 Bedienungsanleitung

23 August 2024

Jablotron JA-60G Bedienungsanleitung

22 August 2024

Jablotron JA-60B Bedienungsanleitung

22 August 2024

Jablotron JA-63E Bedienungsanleitung

22 August 2024

Jablotron JA-80D Bedienungsanleitung

22 August 2024

Jablotron JA-50S Bedienungsanleitung

22 August 2024

Jablotron JA-63F Bedienungsanleitung

22 August 2024

Jablotron GBS-200 Bedienungsanleitung

20 August 2024

Jablotron JA-63F wireless keypad Bedienungsanleitung

18 August 2024

Jablotron CA-322 Accent Bedienungsanleitung

18 August 2024

Bedienungsanleitung Sicherheit

Neueste Bedienungsanleitung für -Kategorien-

NetworX NX-595E IP Communication Module Bedienungsanleitung

5 Oktober 2024

Unitron Smart Alert Systeem Bedienungsanleitung

24 September 2024

NetworX NX-408 Bedienungsanleitung

20 September 2024

Theben Luxa 102.150 - 1020961-2 Bedienungsanleitung

19 September 2024

Elro AB600P - MOTION DETECTOR Bedienungsanleitung

17 September 2024

Elro AG40KE Bedienungsanleitung

17 September 2024

Elro CS95DVR Bedienungsanleitung

16 September 2024

BTicino Classe100 X16E Beveiliging Bedienungsanleitung

16 September 2024

One2track Safety Angel Bedienungsanleitung

27 August 2024

Sygonix SY-3851632 Bedienungsanleitung

27 August 2024