Jablotron JA-60V Bedienungsanleitung

Jablotron Sicherheit JA-60V

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Jablotron JA-60V (2 Seiten) in der Kategorie Sicherheit. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

JA-60V Wireless outdoor PIR detector 1 MEB 52101

JA-60V Wireless outdoor P.I.R. motion detector

The JA-60V is an outdoor intruder detector designed to detect human

body movement in a protected area. Used PIR detector produced by Optex

has two double-layered detection patterns (upper and lower) both have to

be activated to trigger the alarm. This reduces false alarms, particularly

those caused by temperature changes, light reflection or small animals.

A tamper triggers an alarm if there is any attempt to tamper with the

detector.

The built-in transmitter is fully compatible with all JA-6X control panels.

Specifications

Power 3 V - 2 x AAA battery 1.5V

Battery life time about 1 year

Working frequency 433.92 MHz

RF Power

10 mV

Working range max. 100 m (open area)

Specification of the Optex VX 402R detector

Detection method Passive infrared

Coverage 12 m / 90° ; 14 segments

Mounting height 0.8 – 1.2 m

Detection speed 0.3 – 1.5 ms-1

Battery saving timer 5 or 120 seconds

LED indicator only in the test mode

Environmental class IV (EN 50131-1)

Operating temperature -20°C to +50°C

Waterproof IP54

Humidity 95%

Dimension 198 x 80 x 108 mm

Security grade 2 (EN 50131-1)

Can be operated according to ERC/REC 70-03

Hereby, Jablotron Ltd., declares that this JA-60V is in

compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.cz, section Technical support.

Contents of the set: detector JA-60V, pole mounting kit, screw kit, area

masking plates, 2 AAA batteries

Installation

Select the proper place for mounting the detector according to

following:

1. Install the detector perpendicular to the ground to make upper

detection area parallel to the ground

2. Installation height is 0.8 – 1.2 m

3. Mount the detector so that a majority of traffic flow is across the

detection pattern

4. Too much light such as strong sunlight directed exactly to the sensor

may cause unstable condition. It is highly recommended to avoid

such installation.

3.1.1. 3.

0.8

1.2 m

To open the detector:

1. Unscrew the lock screw and remove the top cover.

2. Unscrew the screws fastening the back box. Remove the back

box.

NOTE: never touch surface of the PIR sensor.

Fix the detector to desired place. Detector can be fixed directly on the

wall or by using supplied fix bracket on the pole (Ø 43 – 48 mm).

Optical Part

Cover

Lock Screw

Back Box

Pole Mounting

Bracket

Setting Switches

Enrollment of the detector to the receiver

The transmitter is placed below the optical part of the detector. Study

the installation manual of the receiver unit (control panel) first to learn how

enter the enrolling mode. When the receiver is switched to the enrolment

mode insert the two provided AAA batteries into the detector (polarity is

marked in the detector). The detector will generate an enrollment signal

after the batteries are installed.

INSTANT

DELAY

JA-60N transmitter

• Use DIP switch no. 1 to select the reaction of the system:

- instant (position ON)

- delay (position 1).

• Leave DIP switch no. 2 in position ON.

Adjustment

The upper detection area stays parallel to the ground. The lower area

moves as shown below depending on the position of the setting switch.

Detection length is therefore limited by the length of lower detection

area, since both upper and lower detection area have to be activated

at the same time to trigger the detector.

distance 0 - 12 m

distance 0 - 2 m

distance 0 - 5 m

distance 0 - 8 m

JA-60V Wireless outdoor PIR detector 2 MEB 52101

Detection length setting table:

Max. detection length

Position Standard See Note bellow

A 12 m 10.0 to 15.0 m

B 8 m 6.0 to 10.0 m

C 5 m 4.0 to 5.5 m

D 2 m 1.5 to 2.5m

NOTE: the maximum detection length may vary as above due to

environmental thermal condition.

Detection Area

Level A,B,C,D

No Detection

Tolerance

Active area angle is 90°. By holding the pyro-electric unit it can be turned

in to desired direction ( in 15° steps).

45 90

Area masking – by provided masking plates section of the detection area,

which is exposed to the reflection of the sunlight, car light etc. can be

masked.

Sensitivity of the PIR sensor can be set by “SENS” switch in three

steps:

L - low

M - middle

H - high

Other parameters can be set using a DIP switch:

LED indicator OFF LED indicator ON

120 s 5 s Battery saving timer

4x 2x Pulse count

LED indicator is to be used for testing of the PIR detector. During

normal operation period is recommended to switch it off to save the

battery.

Depending on the 120s/5s battery saving timer DIP switch the movement

sensor will be blocked for a period of 5 or 120 seconds after a movement is

detected to conserves battery energy.

Depending on the Pulse count DIP switch the detector (both upper &

lower detection area) must be triggered 2 or 4 times to transmit the

alarm signal.

Operation test

Turn the LED indicator on, set the “battery saving timer” to 5 seconds

and close the detector. Every 5 seconds any movement in the

detection area will be indicated by the LED indicator and the alarm

information will be sent to the control panel.

Operation

To increase batteries lifetime it is highly recommended to switch the

“battery saving timer” to 120 seconds and switch off the LED indicator

in normal operating mode. The movement sensor will be blocked for 5 or

120 seconds after a movement is detected. This means that if there is

constant movement in the detection area the detector will transmit

information about the movement only once every 5 or 120 seconds.

Battery testing and replacement

The detector automatically checks the condition of its batteries. If it is

necessary to replace the batteries, the detector will inform the control panel

about it. If a low battery is indicated the detector works as normal but,

batteries should be replaced as soon as possible (within a week).

Before replacing the batteries, the control panel must be switched into

mode, which allows detectors opening (User mode or Programming

mode).

Use only high quality alkaline AAA batteries for replacement.

Note: Dispose of batteries safely depending on the type of the batteries and

local regulation. Although this product does not contain any harmful materials

we suggest you to return the product to the dealer or directly to the producer

after usage.

Troubleshooting

Problem Probable cause Remedy

Lower detection area is

unnecessarily long Set the detection area

properly

Detector receives

reflection of the reflector,

sunlight, car light etc.

Remove the reflector,

mask the area exposed to

the reflection of light or

change position of the

detector

There is a heat source in

the area that can cause

fast temperature change

(stove, heater etc.)

Remove the source of

heat or change position of

the detector

Detector

makes false

alarms

There is any moving object

in the area (laundry on the

clothesline, plans etc.)

Remove the moving object

or change position of the

detector

Detection area is not set

properly Set the detection are

properly

Occasionally

no detection Sensitivity is set to low (L) Change sensitivity to

medium (M) or high (H)

Low battery Replace the battery

LED does not light Turn LED switch ON

Detector

fails to work LED indicator lights but no

reaction on the control

panel

The control panel is out of

range, check the battery,

try to replace detector or

control panel

198

108

Dimensions

Note: Although this product does not contain any harmful

materials we suggest you to return the product to the dealer

or directly to the producer after usage.

Internet: www.jablotron.cz

Tel.: 483 559 999

fax: 483 559 993

Pod Skalkou 3 3

466 01 Jablonec nad Nisou

123

Produktspezifikationen

Marke:	Jablotron
Kategorie:	Sicherheit
Modell:	JA-60V

Brauchst du Hilfe?

Wenn Sie Hilfe mit Jablotron JA-60V benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sicherheit Jablotron

Jablotron EYE-02 Bedienungsanleitung

23 August 2024

Jablotron JA-60G Bedienungsanleitung

22 August 2024

Jablotron JA-60B Bedienungsanleitung

22 August 2024

Jablotron JA-63E Bedienungsanleitung

22 August 2024

Jablotron JA-80D Bedienungsanleitung

22 August 2024

Jablotron JA-50S Bedienungsanleitung

22 August 2024

Jablotron JA-63F Bedienungsanleitung

22 August 2024

Jablotron GBS-200 Bedienungsanleitung

20 August 2024

Jablotron JA-63F wireless keypad Bedienungsanleitung

18 August 2024

Jablotron CA-322 Accent Bedienungsanleitung

18 August 2024

Bedienungsanleitung Sicherheit

Neueste Bedienungsanleitung für -Kategorien-

NetworX NX-595E IP Communication Module Bedienungsanleitung

5 Oktober 2024

Unitron Smart Alert Systeem Bedienungsanleitung

24 September 2024

NetworX NX-408 Bedienungsanleitung

20 September 2024

Theben Luxa 102.150 - 1020961-2 Bedienungsanleitung

19 September 2024

Elro AB600P - MOTION DETECTOR Bedienungsanleitung

17 September 2024

Elro AG40KE Bedienungsanleitung

17 September 2024

Elro CS95DVR Bedienungsanleitung

16 September 2024

BTicino Classe100 X16E Beveiliging Bedienungsanleitung

16 September 2024

One2track Safety Angel Bedienungsanleitung

27 August 2024

Sygonix SY-3851632 Bedienungsanleitung

27 August 2024