Jablotron GBS-210 Bedienungsanleitung

Jablotron Sicherheit GBS-210

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Jablotron GBS-210 (1 Seiten) in der Kategorie Sicherheit. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

GBS-210 „VIVO“ glass break detector 2/2 MGJ51009

GBS-210 “VIVO” glass break detector

The GBS-210 glass break detector detects the breaking of glass

windows. A dual technology detection method (air pressure and sound

analysis) is used. Used processing guarantees high sensitivity to the

breaking of all types of glass. The sensitivity can be adjusted to compensate

for various window sizes and mounting distances. The GBS-210

distinguishes itself with outstanding RF immunity. A built in LED indicator

allows for easy testing and it also provides an optional alarm memory feature.

Installation

Sensitivity adjustment

LED indicator

MEM/TEST jumper

The Vivo is designed for indoor applications. It should be mounted on a

flat wall. The unit must have an unobstructed view of the protected glass (in

the case of heavy curtains, mount the detector on the window frame behind

the curtains). Do not place the detector close to any apparatuses that can

generate air pressure changes, low frequency noise or vibrations.

1. Open the cover of the detector (press in the plastic tab on the

bottom with a screwdriver).

2. Remove the PCB by pressing the flexible tab.

3. Punch through the pre-formed holes for cables and screws.

4. Attach the rear housing section to the wall.

5. Return the PCB into the housing and connect wires to the

terminals.

6. Close the cover.

Note: To avoid damaging the microphone when closing the cover,

ensure that the front housing is properly aligned before snapping shut!

Terminals

+12V, GND power supply

TAMPER tamper output (normally closed)

RELAY alarm output (normally closed)

Jumpers

MEM/TEST jumper controls the red LED function in the following way:

TEST red LED confirms detector’s triggering

MEM red LED indicates an alarm memory (it can be erased by

temporarily switching off the power supply or disconnecting

the jumper).

If the jumper is removed, the red LED will remain off.

Testing and adjusting the detector

Place the MEM/TEST jumper to the TEST position (red LED will indicate

triggering).

 Strike carefully the glass with a cushioned instrument. Attention,

do not break the glass!

 The red LED will flash shortly after a strike if the air pressure

sensor sensitivity is suitably set.

 The sensitivity can be adjusted with the variable resistor.

Note: Too high sensitivity can be a source of false alarms.

 For complete testing of the detector it is recommended to use the

GBT-212 glass break simulator. The red LED will light for 2

seconds if glass breaking is detected.

GBS-210 “VIVO” working range diagram

Notes:

The memory function can be used to determine the source of an alarm in

the system. If several detectors are used in one zone, you can set the MEM/TEST

jumper into the MEM position. Then, if this detector triggers an alarm, the red LED

will remain on until the power supply is switched off or the MEM/TEST jumper is

disconnected. The detector operates as usual even while the memory of alarm is

indicated.

A glass break detector located at the entrance can trigger a false alarm

when opening the door (air pressure change combined with keys clinking on glass

or a door’s squeaking can simulate the glass break noise). Therefore it is

recommended to connect the glass break detector into the delay zone of a control

panel.

If there is any device in the protected area which can generate a loud noise

(air conditioning, heating or cooling systems etc.), ensure that this noise does not

trigger the glass break alarm. If it does, it is necessary to relocate the detector or

assure that these devices will not be on when the security system is armed.

Specification

Power supply: 12 V DC ± 25%

Power consumption (LED off): max.10 mA

Maximum consumption (LED on): max. 35 mA

Terminals size: 1 mm2

Alarm output: normally closed, max. 60V / 50 mA,

internal resistance max.16 Ohm

Tamper output: normally closed, max. 60 V / 50 mA,

internal resistance max.16 Ohm

Detection range: max. 9 m

Minimum glass dimensions: 0.6 x 0.6 m

Initialization: max. 60 s

Security level - EN 50131-1, CLC/TS 50 131-2-7-1 grade 2,

Environment - class II. – general indoor, (EN 50131-1)

Operating temperatures -10 to +40 °C

EMC EN50130-4,EN 55022

JABLOTRON ALARMS a.s. hereby declares that the GBS-210 is

in compliance with the essential requirements and other relevant

provisions of Directive 2004/108/EC. The original of the conformity

assessment can be found on the web site www.jablotron.com,

Technical Support section.

Note: Although this product does not contain any harmful materials

we suggest you return the product to the dealer or directly to the

manufacturer after use.

Produktspezifikationen

Marke:	Jablotron
Kategorie:	Sicherheit
Modell:	GBS-210

Brauchst du Hilfe?

Wenn Sie Hilfe mit Jablotron GBS-210 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sicherheit Jablotron

Jablotron EYE-02 Bedienungsanleitung

23 August 2024

Jablotron JA-60G Bedienungsanleitung

22 August 2024

Jablotron JA-60B Bedienungsanleitung

22 August 2024

Jablotron JA-63E Bedienungsanleitung

22 August 2024

Jablotron JA-80D Bedienungsanleitung

22 August 2024

Jablotron JA-50S Bedienungsanleitung

22 August 2024

Jablotron JA-63F Bedienungsanleitung

22 August 2024

Jablotron GBS-200 Bedienungsanleitung

20 August 2024

Jablotron JA-63F wireless keypad Bedienungsanleitung

18 August 2024

Jablotron CA-322 Accent Bedienungsanleitung

18 August 2024

Bedienungsanleitung Sicherheit

Neueste Bedienungsanleitung für -Kategorien-

NetworX NX-595E IP Communication Module Bedienungsanleitung

5 Oktober 2024

Unitron Smart Alert Systeem Bedienungsanleitung

24 September 2024

NetworX NX-408 Bedienungsanleitung

20 September 2024

Theben Luxa 102.150 - 1020961-2 Bedienungsanleitung

19 September 2024

Elro AB600P - MOTION DETECTOR Bedienungsanleitung

17 September 2024

Elro AG40KE Bedienungsanleitung

17 September 2024

Elro CS95DVR Bedienungsanleitung

16 September 2024

BTicino Classe100 X16E Beveiliging Bedienungsanleitung

16 September 2024

One2track Safety Angel Bedienungsanleitung

27 August 2024

Sygonix SY-3851632 Bedienungsanleitung

27 August 2024