IOptron HAZ46 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für IOptron HAZ46 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
1
iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com
Quick Start Guide
HAZ Strain Wave Gear Alt- GoTo Mount Az
Models: HAZ31, HAZ46 & HAZ71
PACKAGE CONTENTS1
Telescope mount HAZ
Hand controller (HC) Go2Nova® 9 with built-in WiFi 840
6P6C hand controller cable
USB 2.0 cable
AC adapter -240V, 12V 5A DC output (for indoor use only), or 12.6V baery charger 100
Carrying case
ONLINE RESOURCES www.iOptron.com ( )
Quick Start Guider and User’s Manual
Firmware upgrades (check online for the latest version)
Computer control
Oponal tripod/Tri-pier/ MiniPier/Leveling MiniPier
1 Contents and design may change from me to me without noce.
2
iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com
HAZ is operated under unbalanced condion and could be pped o if tripod is not secured.
1. Remove mount head from package.
2. Set up tripod: The mount can be aached to a tripod
or a pier/minipier -16 threaded post. with a 3/8”
Extend the tripod legs. Adjust the tripod height and
level it. Tighten tripod leg locking knob to secure the
tripod. Shown below is a carbon ber tripod #8061A
which can be used for mulple mounts. Remove
center post and alignment peg, if there is any
installed. Retreat tripod supporng tray locking knob
so the tripod center bolt can be push up through the
tripod head.
3. Aach mount head: Align the HAZ mount head base
hole to the tripod center rod. Tighten the center bolt
to secure the mount. Tighten the tray lock to secure
the tripod legs.
If you have a HAZ71 mount, you may use a MiniPier.
Level the mount by adjusng the tripod legs. Use the
build-in Bubble Level Indicator or an external leveler
for this purpose.
Center post
Tray locking
knob
Center bolt
locking knob
Center bolt
3
iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com
4. Convert dovetail saddle: The latest HAZ mount
equips with a Vixen/Losmandy dual saddle to accept
a Vixen or a Losmandy-D dovetail mounng bar.
To convert dovetail saddle for binocular mounng.
(1) Remove dovetail saddle from the adapng plate
by unscrew four socket screws;
(2) Aach the saddle onto the top of the adapng
plate, aligned the moung holes and ghten the
screws.
Make sure the the Bino is facing upward!
5. Aach telescope: There are two arrows on the
dovetail saddle. One is for telescope mounng
(dovetail saddle side-mounted) and the other is for
binocular (dovetail up-mounted). Slide the
telescope/binocular into the dovetail saddle. Make
sure that the objecve end is poinng to the
direcon as the arrow mark on the dovetail pointed
to.
Tighten dovetail saddle locking screw to secure the
telescope
To prevent the scope sliding out from the dovetail
saddle by accident, you may thread a screw on the
boom of the dovetail bar as a safety stopper.
Saddle
Adapting plate
Treaded holes for
Saddle screws


Produktspezifikationen

Marke: IOptron
Kategorie: Nicht kategorisiert
Modell: HAZ46

Brauchst du Hilfe?

Wenn Sie Hilfe mit IOptron HAZ46 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert IOptron

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-