Intel SSDSC2BA800G4 Bedienungsanleitung

Intel Solid-State-Laufwerk (SSD) SSDSC2BA800G4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Intel SSDSC2BA800G4 (12 Seiten) in der Kategorie Solid-State-Laufwerk (SSD). Dieser Bedienungsanleitung war für 38 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/12

Intel® Solid-State Drive

Installation Guide 1

Intel® Solid-State Drive

Installation Guide

Overview

Installing an Intel SSD consists of three main steps:

Before you Begin

•Download and save the Intel Data Migration Software to your current storage device:

http://www.intel.com/go/ssdinstallation

•Confirm you have the necessary hardware for installation:

Note: Contents vary based on package purchased.

This guide explains how to install an Intel® Solid-State Drive

(Intel® SSD) in a SATA-based desktop or notebook computer.

The instructions include migrating your data from your current

storage device (such as a hard disk drive) to your new Intel SSD

using Intel® Data Migration Software.

1. Connect the Intel SSD to your computer.

2. Migrate your data from your current storage device to your new Intel SSD.

3. Swap the placement of your current storage device with your new Intel SSD.

Hardware item Required for

1. SATA-to-SATA interface cable Desktop computers

2. SATA power adapter Desktop computers without a SATA power cable

3. 3.5-inch mounting adapter and screws Desktop computers with 3.5-inch drive bay

4. USB-to-SATA cable Notebook computers

5. Drive sleeve Notebook computers (optional - for use with your old

storage device after the SSD is installed)

6. Phillips screwdriver Most computers

13 4 5 6

Intel® Solid-State Drive

2 Installation Guide

Intel® Solid-State Drive

SSD Handling Precautions

Observe the following before beginning the installation:

•Keep the SSD in the protective anti-static container until you are ready to install.

•Handle the SSD with care. Do not touch the gold connectors.

•To minimize static electricity, touch the computer case before handling the SSD.

•Do not remove the encasement or disassemble the SSD; these actions void the SSD warranty.

This step explains how to connect the Intel SSD to your computer in preparation for migrating

your data. Note that your current storage device remains installed until the final step of the

installation, “Swap Your Drives” on page 8.

Follow the steps for your platform:

—“Desktop Computers” (next section)

—“Notebook Computers” on page 4

Desktop Computers

1. If your desktop computer has a 3.5-inch drive bay, attach the Intel SSD to the mounting

adapter. (This helps the SSD fit securely in a drive bay.) If your desktop computer has a 2.5-

inch drive bay, you do not need to attach the mounting adapter. Go to step 2 in this section.

a. With the SSD right side up (Intel logo showing), place the Intel SSD on the mounting

adapter. Make sure the edge of the Intel SSD (with connectors) aligns with the edge of the

mounting adapter. See Figure 1.

b. Turn the SSD and mounting adapter over and insert one screw in each mounting hole on the

bottom of the mounting adapter. See Figure 1.

Figure 1. Place and attach Intel SSD on mounting adapter

2. Power off the computer. Keep the power cable connected.

3. Remove the computer case.

Refer to your computer documentation to determine how to safely remove the computer case.

1. Connect the Intel SSD to your Computer

Intel® Solid-State Drive

Installation Guide 3

Intel® Solid-State Drive

4. Connect one end of the SATA-to-SATA interface cable to a SATA interface connector or

SATA host adapter on your computer motherboard and connect the other end to the

Intel SSD. See Figure 2.

Note: The SATA cable connectors are keyed to ensure correct orientation and contain a

locking bracket for securing in place. Insert cables gently. Do not use excessive force.

5. Locate an available SATA power cable (connected to the internal computer power supply) and

connect it to the Intel SSD. See Figure 2.

Note: Most computers have an available SATA power cable. If your computer does not have a

SATA power cable and instead uses a 4-pin power connector, use a SATA power adapter.

(The SATA power adapter comes with certain packages or can be purchased separately.)

Figure 2. Connect SATA interface and power cables

6. Slide the connected Intel SSD with mounting adapter into an available 3.5-inch drive bay, or

secure the Intel SSD to the computer by inserting one screw in each of the side-mounting or

bottom-mounting holes.

7. Power on the computer and wait for the operating system to recognize the Intel SSD.

A message appears when the SSD is recognized.

The Intel SSD is now connected. Proceed to “Migrate Your Data” on page 5.

1. SATA-to-SATA interface cable: Connect to SATA interface connector on computer motherboard and to Intel SSD.

2. SATA power cable (or SATA power adapter): Connect from power supply to Intel SSD.

Produktspezifikationen

Marke:	Intel
Kategorie:	Solid-State-Laufwerk (SSD)
Modell:	SSDSC2BA800G4
Breite:	- mm
Tiefe:	- mm
Gewicht:	88 g
Produktfarbe:	Silber
Höhe:	7 mm
Betriebstemperatur:	0 - 70 °C
Unterstützte Sicherheitsalgorithmen:	256-bit AES
Warentarifnummer (HS):	84717070
Eingebaut:	Ja
Unterstützt Windows-Betriebssysteme:	Ja
Schnittstelle:	Serial ATA III
Mittlere Betriebsdauer zwischen Ausfällen (MTBF):	2000000 h
Prozessor Lithografie:	20 nm
Nachhaltigkeitszertifikate:	RoHS
SSD Speicherkapazität:	800 GB
SSD-Formfaktor:	2.5"
Datenübertragungsrate:	6 Gbit/s
Lesegeschwindigkeit:	550 MB/s
Energieverbrauch (idle):	0.6 W
Schreibgeschwindigkeit:	460 MB/s
Speichertyp:	MLC
Energieverbrauch (Betrieb):	5.9 W
Zufälliges Lesen (100% span):	85000 IOPS
Zufälliges Schreiben (100% span):	39000 IOPS
Vibrationen in Betrieb:	2.17 G
Vibrationen außer Betrieb:	3.13 G
Lese-Latenzzeit:	55 µs
Schreib-Latenzzeit:	66 µs
Marktsegment:	Server
Status:	Launched
Produktfamilie:	Rechenzentrum SSD
Startdatum:	2015-01-27T00:00:00
Produktcodename:	Haleyville
Produktreihe:	Intel DC S3710
Geboren am:	Q1'15
Produktbezeichnung:	Intel SSD DC S3710 Series (800GB, 2.5in SATA 6Gb/s, 20nm, MLC)
Lithographie:	20 nm
Verbesserte Stromausfall-Datenschutz Technologie:	Ja
SSD Temperaturüberwachung:	Ja
End-to-End Datenschutz:	Ja
Unkorrigierbare Bit Error-Rate (UBER):	< 1 per 10^17 bits read
SSD ARK ID:	84239
SSD-Nutzungs-Tag:	Rechenzentrum
Intel® High Endurance Technology (HET):	Ja
Laufwerkskapazität:	800 GB
URL Produktbeschreibung:	http://www.intel.com/content/www/us/en/solid-state-drives/ssd-dc-s3710-brief.html
SSD-Beständigkeitsbewertung:	16.9PB
SSD-Hardwareverschlüsselung:	AES 256 bit
SSD-Stromverbrauch (aktiv):	5.9W
SSD-Stromverbrauch (Leerlauf):	0.6W
SSD-Schock:	1000 G/0.5ms
SSD-Gewicht:	88 grams g
Leserate:	550 MB/s
Schreibrate:	460 MB/s