Inovonics EchoStream EN1235S Bedienungsanleitung
Inovonics
Controller
EchoStream EN1235S
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Inovonics EchoStream EN1235S (2 Seiten) in der Kategorie Controller. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
© 2010 Inovonics - www.inovonics.com
EchoStream® EN1233S/D and EN1235S/D
Pendant Transmitter
Installation Instructions - 05596B
1 Overview
1.1 Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics
Wireless technical services:
• E-mail: support@inovonics.com
• Phone: (800) 782-2709
1.2 Pendant Transmitter Components
Figure 1 Pendant Transmitter components
2 Installation and Startup
2.1 Install/Replace the Battery
1. Pry the housing apart at either end and pull the two halves
apart.
2. If replacing a battery, remove the old battery.
3. Install the new battery.
4. Press the Reset button to initialize the transmitter.
2.2 Select the Frequency Band
EchoStream products are able to use a range of radio frequencies,
and must be configured for your geographic area. To configure the
transmitter:
1. Pry the housing apart at either end and pull the two halves
apart.
2. Place a selection jumper on the appropriate frequency band
selection pins.
• Leave the jumper off the pins to set the frequency range to
902-928 MHz for North America.
• Place the jumper on the bottom pins, marked NZ, to set the
frequency range to 921-928 MHz for New Zealand.
• Place the jumper on the top two pins, marked AU, to set the
frequency range to 915-928 MHz for Australia.
3. ResetPress the button to complete configuration.
Caution: When pressing the Reset button, make sure you don’t
also touch the frequency band selection pins. Touching the
frequency band selection pins while pressing the Reset button can
inadvertently set the pendant to the wrong frequency band.
2.3 Register the Pendant Transmitter
The pendant transmitter must be registered with the system in order
to be monitored and supervised. When supervised, the pendant
transmitter will send a check-in message to the serial receiver or
network coordinator every three minutes.
Each pendant has a unique factory-programmed identification
number. Refer to the control panel’s installation instructions for
details on registering a transmitter.
1. When prompted by the receiver to reset transmitter, press the
Reset button.
2. Replace the cover.
Caution: The pendant should be tested after registration to ensure
operation. To test the pendant, activate each of the conditions and
ensure an appropriate response.
3 Operation
3.1 Using The EN1233 Pendant Chain
Always use the chain included with the ES1233. Substituting
stronger cords or chains may result in injury to the wearer.
3.2 Converting the Pendant Transmitter Belt Clip
If you’d like to convert the pendant transmitter belt clip to a belt loop,
secure the bottom of the belt clip to the housing with a coarse
thread screw.
Figure 2 Use a coarse thread screw to secure the belt clip
3.3 Operate the Pendant Transmitter
To activate single button transmitters, press the button for at least
one second. To activate double button transmitters, press both
buttons simultaneously. Alarm signals are transmitted multiple times
and are indicated by the blinking transmission LED. When the
buttons are released, the transmitter sends an alarm restoral
signal.To test a transmitter, activate the alarm by pressing the
button(s).
4 Specifications
Typical battery life: 3-5 years
Battery type (BAT608): Panasonic CR2 or equivalent
Operating environment: 0 to 60°C (32 to 140°F), noncondensing
A BReset button Frequency band selection pins
CBattery
B
AC
Printing Instructions
1. Print Duplex
2. Align and orient back page to match front
page.
3. Cut on dashed line
4. Fold cutsheet in half along the 8.5" axis.
© 2010 Inovonics - www.inovonics.com
Note: Specifications and data are subject to change without notice.
5 Warranty and Disclaimer
Note: Changes or modifications to this unit not expressly approved
by Inovonics Wireless Corporation may void the installer's authority
to operate the equipment as well as the product warranty.
Inovonics Wireless Corporation ("Inovonics") warrants its products
("Product" or "Products") to conform to its own specifications and to
be free of defects in materials and workmanship under normal use
for a period of thirty-six (36) months from the date of manufacture.
Within the warranty period, Inovonics will repair or replace, at its
option, all or any part of the warranted Product. Inovonics will not be
responsible for dismantling and/or reinstallation charges. To
exercise the warranty, the User ("User", "Installer" or "Consumer")
must work directly through their authorized distributor who will be
given a Return Material Authorization ("RMA") number by
Inovonics. Details of shipment will be arranged directly through the
authorized distributor.
This warranty is void in cases of improper installation, misuse,
failure to follow installation and operating instructions, alteration,
accident or tampering, and repair by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other
warranties, obligations or liabilities, whether written, oral, express,
or implied. There is no warranty by Inovonics that Inovonics product
will be merchantable or fit for any particular purpose, nor is there
any other warranty, expressed or implied, except as such is
expressly set forth herein. In no event shall Inovonics be liable for
an incidental, consequential, indirect, special, or exemplary
damages, including but not limited to loss of profit, revenue, or
contract, loss of use, cost of down time, or interruption of business,
nor any claim made by distributor's customers or any other person
or entity.
This warranty will not be modified or extended. Inovonics does not
authorize any person to act on its behalf to modify or extend this
warranty.
This warranty will apply only to Inovonics Products. Inovonics will
not be liable for any direct, incidental, or consequential damage or
loss whatsoever, caused by the malfunction of Product due to
products, accessories, or attachments of other manufacturers,
including batteries, used in conjunction with Inovonics Products.
Note: E-mail support@inovonics.com for a copy of the CE
Declaration of Conformity.
Produktspezifikationen
Marke: | Inovonics |
Kategorie: | Controller |
Modell: | EchoStream EN1235S |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Inovonics EchoStream EN1235S benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Controller Inovonics
16 August 2024
Bedienungsanleitung Controller
- Controller Samsung
- Controller Asus
- Controller Belkin
- Controller Gembird
- Controller Hama
- Controller HP
- Controller HyperX
- Controller Logitech
- Controller Nacon
- Controller Niceboy
- Controller Saitek
- Controller Sony
- Controller SteelSeries
- Controller Sweex
- Controller T'nB
- Controller Trust
- Controller Canon
- Controller Velleman
- Controller Hori
- Controller König
- Controller Thomson
- Controller Schneider
- Controller Pyle
- Controller Mitsubishi
- Controller Bose
- Controller Denon
- Controller Pioneer
- Controller JBL
- Controller One For All
- Controller Vivanco
- Controller BeamZ
- Controller Tascam
- Controller Perel
- Controller Aruba
- Controller Lindy
- Controller Thrustmaster
- Controller TOA
- Controller MSI
- Controller Tripp Lite
- Controller Marshall
- Controller Razer
- Controller Honeywell
- Controller Marshall Electronics
- Controller SBS
- Controller Parrot
- Controller Reely
- Controller Zebra
- Controller Adj
- Controller Supermicro
- Controller Genesis
- Controller Behringer
- Controller Mackie
- Controller Numark
- Controller Eurolite
- Controller Monoprice
- Controller Monacor
- Controller Hunter
- Controller Esperanza
- Controller Lumens
- Controller Korg
- Controller DataVideo
- Controller Manfrotto
- Controller Tracer
- Controller Cisco
- Controller Boss
- Controller Synology
- Controller Kramer
- Controller Irritrol
- Controller Jumbo
- Controller Vaddio
- Controller RCA
- Controller Datalogic
- Controller HQ Power
- Controller Nintendo
- Controller Kicker
- Controller Speed-Link
- Controller DBX
- Controller Draper
- Controller Hikvision
- Controller Radial Engineering
- Controller Sven
- Controller PreSonus
- Controller ART
- Controller Senal
- Controller PDP
- Controller IK Multimedia
- Controller Krom
- Controller ASTRO Gaming
- Controller Gamesir
- Controller Fusion
- Controller GeoVision
- Controller Gossen Metrawatt
- Controller Icon
- Controller IHome
- Controller Media-tech
- Controller Naxa
- Controller Schaudt
- Controller SecurityMan
- Controller Steca
- Controller AMX
- Controller Universal Remote Control
- Controller Vizio
- Controller Siig
- Controller Intel
- Controller Zephyr
- Controller RGBlink
- Controller StarTech.com
- Controller Konix
- Controller Monster
- Controller Niles
- Controller Polsen
- Controller Atlantis Land
- Controller Atlas Sound
- Controller Magnus
- Controller LSI
- Controller ATen
- Controller KanexPro
- Controller Lab Gruppen
- Controller SmartAVI
- Controller Natec
- Controller EtiamPro
- Controller Chauvet
- Controller Premier Mounts
- Controller Juniper
- Controller Phoenix Contact
- Controller Music Hall
- Controller Audac
- Controller OSD Audio
- Controller BZBGear
- Controller DreamGEAR
- Controller Crestron
- Controller GOgroove
- Controller PowerA
- Controller Atlona
- Controller LYYT
- Controller Elite Screens
- Controller Bigben Interactive
- Controller Rolls
- Controller Sonifex
- Controller Leviton
- Controller Apricorn
- Controller 8BitDo
- Controller Alfatron
- Controller Highpoint
- Controller Steelplay
- Controller AViPAS
- Controller Auray
- Controller Vakoss
- Controller Areca
- Controller Savio
- Controller Heritage Audio
- Controller Ltech
- Controller CTA Digital
- Controller Canyon
- Controller MuxLab
- Controller Kanlux
- Controller EXSYS
- Controller Amer
- Controller ALC
- Controller LumenRadio
- Controller Moza
- Controller Axor
- Controller Valcom
- Controller AirTurn
- Controller Dangerous Music
- Controller Clarity
- Controller Softube
- Controller RiotPWR
- Controller IPEGA
- Controller Dadson
- Controller Blizzard Lighting
- Controller Heath Zenith
- Controller Re.corder
- Controller Mitzu
- Controller CoolerMaster
- Controller Dragonshock
- Controller MOGA
- Controller HuddleCamHD
- Controller PTZ Optics
- Controller Balam Rush
Neueste Bedienungsanleitung für -Kategorien-
5 Oktober 2024
4 Oktober 2024
3 Oktober 2024
1 Oktober 2024
Hori Force Feedback Truck Control System Bedienungsanleitung
1 Oktober 2024
30 September 2024
27 September 2024
Nacon Revolution Unlimited Pro Controller PS4 Bedienungsanleitung
27 September 2024
24 September 2024